For Exynos5250 platforms, add CPU operating points and CPU regulator
supply properties for migrating from Exynos specific cpufreq driver
to using generic cpufreq driver.

Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
[b.zolnierkie: split Exynos5250 support from the original patch]
[b.zolnierkie: added CPU regulator supply property for Spring boards]
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Tested-by: NJavier Martinez Canillas <javier@dowhile0.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

There's no need for a simple-bus, place the smsc,usb3503a directly into
the root node. That's what we're going to do on exynos5250-spring.
Reported-by: NTomasz Figa <t.figa@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The GPIO flag 2 has no constant assigned, so this was probably
active-low.
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Use the new style of referencing inherited nodes, use symbolic names,
tidy indentation and reorder includes.

Goal is the alignment of all exynos5250 based device trees for
comparison.
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

drivers/usb/phy/phy-samsung-usb2 driver got replaced by
drivers/phy/phy-samsung-usb2 one.  Remove the leftover hook
from Arndale dts file.

Cc: Mark Brown <broonie@linaro.org>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: NVivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NTushar Behera <trblinux@gmail.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Key code macros improve readability on exnos4210-origen,
exynos4412-origen and exynos5250-arndale boards.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
[kgene.kim@samsung.com: squashed similar two patches]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

LDO4 regulator was getting disabled preventing the system from
going into low power states. Keep it always on to fix it.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add generic compatible strings to the respective board DT files.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds dt entry for ahci sata controller and its
corresponding phy controller.phy node has been added w.r.t
new generic phy framework.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files. For
now enable it for all board files to maintain the enabled status
exisitng prior to this patch.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Apparently, if G3D regulator is powered off, the SoC cannot enter low
power modes and just hangs. This patch fixes this by keeping the
regulator always on when the system is running, as suggested by Exynos 4
User's Manual in case of Exynos4210/4x12 SoCs (Exynos5250 UM does not
have such note, but observed behavior seems to confirm that it is true
for this SoC as well).

This fixes an issue preventing Arndale board from entering sleep mode
observed since commit

346f372f clk: exynos5250: Add CLK_IGNORE_UNUSED flag for pmu clock

that landed in kernel 3.10, which has fixed the clock driver to make the
SoC actually try to enter the sleep mode.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@vger.kernel.org>        [v3.10+]
Tested-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Ensure that unused I2C controllers are not activated, causing problems due
to inappropriate pinmuxing or similar, by marking the controllers as
disabled by default and requiring boards to explicitly enable those that
are in use.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Rather than requiring each board to explicitly disable the SPI controllers
it is not using instead require boards to enable those that they are using.
This is less work overall since normally at most one of the controllers is
in use and avoids issues caused by inappropriate pinmuxing.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The minimum recommended ARM voltage for Exynos5250 at 200MHz
on Arndale board is 0.9125V. Update accordingly.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch rename's the device tree mmc node's from "dwmmc" to "mmc".
According to ePAPR chapter 2.2.2 generic node name recommendation,
it has been opted change from dwmmc to mmc.Also this patch remove the
instance index from the node name.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As fifo-depth property in dw_mmc device tree node is SOC
specific, move this property to exynos5250 SOC specific
file.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: squashed fifo-depth patch for cros5250-common]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

According to ePAPR, chapter 2.3.4, the status property has
defined that it should be set to "disabled" when "the device
is not presently operational, but it might become operational
in the future".

So this patch disable dwmmc node by "status = disabled" in SOC
dts file and enable dwmmc node by "status = okay" in board specific
dts file.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Though the default value is 1, add it explicitly to avoid
unnecessary boot warnings and for consistency.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Updated I2C nodes for HDMI-DDC and HDMI-PHY for Arndale board.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Rather than requiring each board to explicitly disable the I2S controllers
it is not using instead require boards to enable those that they are using.

This is required for audio operation on Arndale, one of the unused I2S
controllers is pinmuxed with the LDO enable GPIOs for the WM1811A.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

For consistency and correctness, since this is a bus, even if not
physical, it is worth to add 'reg' property and unit-address to subnodes.
The 'reg' property would merely be an index. Also for consistency, use
"regulator" as node name as used most commonly across other dts files.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Moves the RTC DT node's "status" property from exynos5250 board
(arndale & snow) dts files to exynos5250.dtsi, since the bindings
in exynos5250.dtsi depicts the RTC h/w completely.
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Fixes the RTC DT node name for Exynos5250 as per the DT node naming
convention.
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

While the Linux driver stack is capable of figuring this out for itself
document the fact that we really do use the internal PHY even with the
directly wired hub on the board to save anyone else having to work this
out for themselves.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The Arndale has a SMSC USB3503 connected in hardware only mode like a PHY,
support it using the usb-nop-xceiv binding.

Note that due to a regrettable decision to use a regulator to represent
the reset signal this uses a fixed voltage regulator to do that, there
is a plan to use the reset controller binding once that is merged so it
does not seem worthwhile to fix the usb-nop-xceiv driver at this point.
Signed-off-by: NMark Brown <broonie@linaro.org>
Tested-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Moves the properties of DP controller to exynos5.dtsi which are common
across exynos5 SoCs like Exynos5250 and Exynos5420.

The PHY DP Node is based on Jingoo Han's <jg1.han@samsung.com> patch
at https://patchwork.linuxtv.org/patch/19189/Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Moves the properties of FIMD DT node which are common across Exynos5 based
SoCs like Exynos5250 and Exynos5420 to exynos5.dtsi
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The default audio module for the Arndale has a WM1811A on it. Add this to
the device tree bindings.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As part of this add nodes for the main wall supply as well as bucks 7
and 8 which are used to drop that down for several of the LDOs.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Fixed voltage regulators (and other similar free standing things) are
supposed to go on a simple-bus for DT correctness reasons.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The out of tree code configures a pullup on the line indicating that it
is an active low interrupt.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Replace /include/ (dtc) with #include (C pre-processor) for all
Samsung DT files
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The issues reported in commit 522ccdb6 ("ARM: dts: Disable the RTC
by default on exynos5") are no longer reproduced on EXYNOS5250 based
Arndale board. Hence re-enabling RTC support for Arndale board.

This is helpful for testing S2R on Arndale board.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds display timing node for a DP panel to Arndale Board DTS file
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add DT node for DP controller to exynos5250 based Arndale Board
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Added HDMI hot plug and regulator nodes to Arndale DT file.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Added MFC codec node to Arndale DT file.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Added vmmc regulator node to Arndale DT file.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Added S5M8767 PMIC DT nodes for Arndale board. Only the used
LDO's/BUCK are defined here. Also the nodes describe the default/reset
state LDO's and no power mangement tuning is implemented. The usage
desription can be found in s5m8767 device tree binding documentation.
Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>