Pull powerpc fixes from Michael Ellerman:
 "Fixes for recently merged code:
   - a fix for the _PAGE_DEVMAP support, which was breaking KVM on
     Power9 radix
   - avoid a (harmless) lockdep warning in the early SMP code
   - return failure for some uses of dma_set_mask() rather than falling
     back to 32-bits
   - fix stack setup in watchdog soft_nmi_common() to use emergency
     stack
   - fix of_irq_to_resource() error check in of_fsl_spi_probe()

  Two fixes going to stable:
   - fix saving of Transactional Memory SPRs in core dump
   - fix __check_irq_replay missing decrementer interrupt

  And two misc:
   - fix 64-bit boot wrapper build with non-biarch compiler
   - work around a POWER9 PMU hang after state-loss idle

  Thanks to: Alistair Popple, Aneesh Kumar K.V, Cyril Bur, Gustavo
  Romero, Jose Ricardo Ziviani, Laurent Vivier, Nicholas Piggin, Oliver
  O'Halloran, Sergei Shtylyov, Suraj Jitindar Singh, Thomas Gleixner"

* tag 'powerpc-4.13-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64: Fix __check_irq_replay missing decrementer interrupt
  powerpc/perf: POWER9 PMU stops after idle workaround
  powerpc/83xx/mpc832x_rdb: fix of_irq_to_resource() error check
  powerpc/64s: Fix stack setup in watchdog soft_nmi_common()
  powerpc/powernv/pci: Return failure for some uses of dma_set_mask()
  powerpc/boot: Fix 64-bit boot wrapper build with non-biarch compiler
  powerpc/smp: Call smp_ops->setup_cpu() directly on the boot CPU
  powerpc/tm: Fix saving of TM SPRs in core dump
  powerpc/mm: Fix pmd/pte_devmap() on non-leaf entries

If the decrementer wraps again and de-asserts the decrementer
exception while hard-disabled, __check_irq_replay() has a test to
notice the wrap when interrupts are re-enabled.

The decrementer check must be done when clearing the PACA_IRQ_HARD_DIS
flag, not when the PACA_IRQ_DEC flag is tested. Previously this worked
because the decrementer interrupt was always the first one checked
after clearing the hard disable flag, but HMI check was moved ahead of
that, which introduced this bug.

This can cause a missed decrementer interrupt if we soft-disable
interrupts then take an HMI which is recorded in irq_happened, then
hard-disable interrupts for > 4s to wrap the decrementer.

Fixes: e0e0d6b7 ("powerpc/64: Replay hypervisor maintenance interrupt first")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

POWER9 DD2 PMU can stop after a state-loss idle in some conditions.

A solution is to set then clear MMCRA[60] after wake from state-loss
idle. MMCRA[60] is a non-architected bit, see the user manual for
details.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Acked-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Reviewed-by: NVaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Pull VFIO fixes from Alex Williamson:

 - SPAPR/EEH config build fix (Murilo Opsfelder Araujo)

 - Fix possible device lock deadlock (Alex Williamson)

 - Correctly size integrated endpoint PCIe capabilities (Alex
   Williamson)

* tag 'vfio-v4.13-rc4' of git://github.com/awilliam/linux-vfio:
  vfio/pci: Fix handling of RC integrated endpoint PCIe capability size
  vfio/pci: Use pci_try_reset_function() on initial open
  include/linux/vfio.h: Guard powerpc-specific functions with CONFIG_VFIO_SPAPR_EEH

Merge misc fixes from Andrew Morton:
 "15 fixes"

[ This does not merge the "fortify: use WARN instead of BUG for now"
  patch, which needs a bit of extra work to build cleanly with all
  configurations. Arnd is on it.   - Linus ]

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  ocfs2: don't clear SGID when inheriting ACLs
  mm: allow page_cache_get_speculative in interrupt context
  userfaultfd: non-cooperative: flush event_wqh at release time
  ipc: add missing container_of()s for randstruct
  cpuset: fix a deadlock due to incomplete patching of cpusets_enabled()
  userfaultfd_zeropage: return -ENOSPC in case mm has gone
  mm: take memory hotplug lock within numa_zonelist_order_handler()
  mm/page_io.c: fix oops during block io poll in swapin path
  zram: do not free pool->size_class
  kthread: fix documentation build warning
  kasan: avoid -Wmaybe-uninitialized warning
  userfaultfd: non-cooperative: notify about unmap of destination during mremap
  mm, mprotect: flush TLB if potentially racing with a parallel reclaim leaving stale TLB entries
  pid: kill pidhash_size in pidhash_init()
  mm/hugetlb.c: __get_user_pages ignores certain follow_hugetlb_page errors

Pull ACPI fixes from Rafael Wysocki:
 "These fix two issues in the ACPI SoC drivers (Intel LPSS and AMD APD),
  a crash in the PCC mailbox initialization code and a WDAT watchdog
  initialization failure.

  Specifics:

   - Fix a device ID of Hisilicon Hip07/08 in the ACPI APD (AMD SoC)
     driver (Hanjun Guo).

   - Fix list corruption (introduced during the 4.11 cycle) in the ACPI
     LPSS (Intel SoC) driver (Hans de Goede).

   - Fix PCC mailbox handling code crash during initialization when PCCT
     is not present and PCC channel 0 is requested (Hoan Tran).

   - Fix a WDAT watchdog initialization issue causing platform device
     creation to fail due to partially overlapping address ranges in
     resources (Ryan Kennedy)"

* tag 'acpi-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: APD: Fix HID for Hisilicon Hip07/08
  mailbox: pcc: Fix crash when request PCC channel 0
  ACPI / watchdog: Fix init failure with overlapping register regions
  ACPI / LPSS: Only call pwm_add_table() for the first PWM controller

Pull power management fixes from Rafael Wysocki:
 "These fix two cpufreq issues, one introduced recently and one related
  to recent changes, fix cpufreq documentation, fix up recently added
  code in the Thunderbolt driver and update runtime PM framework
  documentation.

  Specifics:

   - Fix the handling of the scaling_cur_freq cpufreq policy attribute
     on x86 systems with the MPERF/APERF registers present to make it
     behave more as expected after recent changes (Rafael Wysocki).

   - Drop a leftover callback from the intel_pstate driver which also
     prevents the cpuinfo_cur_freq cpufreq policy attribute from being
     incorrectly exposed when intel_pstate works in the active mode
     (Rafael Wysocki).

   - Add a missing piece describing the cpuinfo_cur_freq policy
     attribute to cpufreq documentation (Rafael Wysocki).

   - Fix up a recently added part of the Thunderbolt driver to avoid
     aborting system suspends if its mailbox commands time out (Rafael
     Wysocki).

   - Update device runtime PM framework documentation to reflect the
     current behavior of the code (Johan Hovold)"

* tag 'pm-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  thunderbolt: icm: Ignore mailbox errors in icm_suspend()
  cpufreq: x86: Make scaling_cur_freq behave more as expected
  PM / runtime: Document new pm_runtime_set_suspended() constraint
  cpufreq: docs: Add missing cpuinfo_cur_freq description
  cpufreq: intel_pstate: Drop ->get from intel_pstate structure

* acpi-soc:
  ACPI: APD: Fix HID for Hisilicon Hip07/08
  ACPI / LPSS: Only call pwm_add_table() for the first PWM controller

* acpi-wdat:
  ACPI / watchdog: Fix init failure with overlapping register regions

* acpi-cppc:
  mailbox: pcc: Fix crash when request PCC channel 0

* pm-core:
  PM / runtime: Document new pm_runtime_set_suspended() constraint

* pm-misc:
  thunderbolt: icm: Ignore mailbox errors in icm_suspend()

* pm-cpufreq-x86:
  cpufreq: x86: Make scaling_cur_freq behave more as expected

* pm-cpufreq-docs:
  cpufreq: docs: Add missing cpuinfo_cur_freq description

* intel_pstate:
  cpufreq: intel_pstate: Drop ->get from intel_pstate structure

Pull NFS client fixes from Anna Schumaker:
 "Two fixes from Trond this time, now that he's back from his vacation.
  The first is a stable fix for the EXCHANGE_ID issue on the mailing
  list, and the other fixes a double-free situation that he found at the
  same time.

  Stable fix:
   - Fix EXCHANGE_ID corrupt verifier issue

  Other fix:
   - Fix double frees in nfs4_test_session_trunk()"

* tag 'nfs-for-4.13-4' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFSv4: Fix double frees in nfs4_test_session_trunk()
  NFSv4: Fix EXCHANGE_ID corrupt verifier issue

This fixes a potential buffer overflow in isdn_net.c caused by an
unbounded strcpy.

[ ISDN seems to be effectively unmaintained, and the I4L driver in
  particular is long deprecated, but in case somebody uses this..
    - Linus ]
Signed-off-by: NJiten Thakkar <jitenmt@gmail.com>
Signed-off-by: NAnnie Cherkaev <annie.cherk@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0').  However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.

Fix the problem by moving posix_acl_update_mode() out of ocfs2_set_acl()
into ocfs2_iop_set_acl().  That way the function will not be called when
inheriting ACLs which is what we want as it prevents SGID bit clearing
and the mode has been properly set by posix_acl_create() anyway.  Also
posix_acl_chmod() that is calling ocfs2_set_acl() takes care of updating
mode itself.

Fixes: 07393101 ("posix_acl: Clear SGID bit when setting file permissions")
Link: http://lkml.kernel.org/r/20170801141252.19675-3-jack@suse.czSigned-off-by: NJan Kara <jack@suse.cz>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kernel panic when calling the IRQ-safe __get_user_pages_fast in NMI
handler.

The bug was introduced by commit 2947ba05 ("x86/mm/gup: Switch GUP
to the generic get_user_page_fast() implementation").

The original x86 __get_user_page_fast used plain get_page() or
page_ref_add().  However, the generic __get_user_page_fast uses
page_cache_get_speculative(), which has VM_BUG_ON(in_interrupt()).

There is no reason to prevent page_cache_get_speculative from using in
interrupt context.  According to the author, putting a BUG_ON there is
just because the code is not verifying correctness of interrupt races.
I did some tests in interrupt context.  There is no issue found.

Removing VM_BUG_ON(in_interrupt()) for page_cache_get_speculative().

Link: http://lkml.kernel.org/r/1501609146-59730-1-git-send-email-kan.liang@intel.com
Fixes: 2947ba05 ("x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation")
Signed-off-by: NKan Liang <kan.liang@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ying Huang <ying.huang@intel.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There may still be threads waiting on event_wqh at the time the
userfault file descriptor is closed.  Flush the events wait-queue to
prevent waiting threads from hanging.

Link: http://lkml.kernel.org/r/1501398127-30419-1-git-send-email-rppt@linux.vnet.ibm.com
Fixes: 9cd75c3c ("userfaultfd: non-cooperative: add ability to report
non-PF events from uffd descriptor")
Signed-off-by: NMike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When building with the randstruct gcc plugin, the layout of the IPC
structs will be randomized, which requires any sub-structure accesses to
use container_of().  The proc display handlers were missing the needed
container_of()s since the iterator is passing in the top-level struct
kern_ipc_perm.

This would lead to crashes when running the "lsipc" program after the
system had IPC registered (e.g. after starting up Gnome):

  general protection fault: 0000 [#1] PREEMPT SMP
  ...
  RIP: 0010:shm_add_rss_swap.isra.1+0x13/0xa0
  ...
  Call Trace:
    sysvipc_shm_proc_show+0x5e/0x150
    sysvipc_proc_show+0x1a/0x30
    seq_read+0x2e9/0x3f0
  ...

Link: http://lkml.kernel.org/r/20170730205950.GA55841@beast
Fixes: 3859a271 ("randstruct: Mark various structs for randomization")
Signed-off-by: NKees Cook <keescook@chromium.org>
Reported-by: NDominik Brodowski <linux@dominikbrodowski.net>
Acked-by: NDavidlohr Bueso <dave@stgolabs.net>
Acked-by: NManfred Spraul <manfred@colorfullife.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In codepaths that use the begin/retry interface for reading
mems_allowed_seq with irqs disabled, there exists a race condition that
stalls the patch process after only modifying a subset of the
static_branch call sites.

This problem manifested itself as a deadlock in the slub allocator,
inside get_any_partial.  The loop reads mems_allowed_seq value (via
read_mems_allowed_begin), performs the defrag operation, and then
verifies the consistency of mem_allowed via the read_mems_allowed_retry
and the cookie returned by xxx_begin.

The issue here is that both begin and retry first check if cpusets are
enabled via cpusets_enabled() static branch.  This branch can be
rewritted dynamically (via cpuset_inc) if a new cpuset is created.  The
x86 jump label code fully synchronizes across all CPUs for every entry
it rewrites.  If it rewrites only one of the callsites (specifically the
one in read_mems_allowed_retry) and then waits for the
smp_call_function(do_sync_core) to complete while a CPU is inside the
begin/retry section with IRQs off and the mems_allowed value is changed,
we can hang.

This is because begin() will always return 0 (since it wasn't patched
yet) while retry() will test the 0 against the actual value of the seq
counter.

The fix is to use two different static keys: one for begin
(pre_enable_key) and one for retry (enable_key).  In cpuset_inc(), we
first bump the pre_enable key to ensure that cpuset_mems_allowed_begin()
always return a valid seqcount if are enabling cpusets.  Similarly, when
disabling cpusets via cpuset_dec(), we first ensure that callers of
cpuset_mems_allowed_retry() will start ignoring the seqcount value
before we let cpuset_mems_allowed_begin() return 0.

The relevant stack traces of the two stuck threads:

  CPU: 1 PID: 1415 Comm: mkdir Tainted: G L  4.9.36-00104-g540c51286237 #4
  Hardware name: Default string Default string/Hardware, BIOS 4.29.1-20170526215256 05/26/2017
  task: ffff8817f9c28000 task.stack: ffffc9000ffa4000
  RIP: smp_call_function_many+0x1f9/0x260
  Call Trace:
    smp_call_function+0x3b/0x70
    on_each_cpu+0x2f/0x90
    text_poke_bp+0x87/0xd0
    arch_jump_label_transform+0x93/0x100
    __jump_label_update+0x77/0x90
    jump_label_update+0xaa/0xc0
    static_key_slow_inc+0x9e/0xb0
    cpuset_css_online+0x70/0x2e0
    online_css+0x2c/0xa0
    cgroup_apply_control_enable+0x27f/0x3d0
    cgroup_mkdir+0x2b7/0x420
    kernfs_iop_mkdir+0x5a/0x80
    vfs_mkdir+0xf6/0x1a0
    SyS_mkdir+0xb7/0xe0
    entry_SYSCALL_64_fastpath+0x18/0xad

  ...

  CPU: 2 PID: 1 Comm: init Tainted: G L  4.9.36-00104-g540c51286237 #4
  Hardware name: Default string Default string/Hardware, BIOS 4.29.1-20170526215256 05/26/2017
  task: ffff8818087c0000 task.stack: ffffc90000030000
  RIP: int3+0x39/0x70
  Call Trace:
    <#DB> ? ___slab_alloc+0x28b/0x5a0
    <EOE> ? copy_process.part.40+0xf7/0x1de0
    __slab_alloc.isra.80+0x54/0x90
    copy_process.part.40+0xf7/0x1de0
    copy_process.part.40+0xf7/0x1de0
    kmem_cache_alloc_node+0x8a/0x280
    copy_process.part.40+0xf7/0x1de0
    _do_fork+0xe7/0x6c0
    _raw_spin_unlock_irq+0x2d/0x60
    trace_hardirqs_on_caller+0x136/0x1d0
    entry_SYSCALL_64_fastpath+0x5/0xad
    do_syscall_64+0x27/0x350
    SyS_clone+0x19/0x20
    do_syscall_64+0x60/0x350
    entry_SYSCALL64_slow_path+0x25/0x25

Link: http://lkml.kernel.org/r/20170731040113.14197-1-dmitriyz@waymo.com
Fixes: 46e700ab ("mm, page_alloc: remove unnecessary taking of a seqlock when cpusets are disabled")
Signed-off-by: NDima Zavin <dmitriyz@waymo.com>
Reported-by: NCliff Spradlin <cspradlin@waymo.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christopher Lameter <cl@linux.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the non-cooperative userfaultfd case, the process exit may race with
outstanding mcopy_atomic called by the uffd monitor.  Returning -ENOSPC
instead of -EINVAL when mm is already gone will allow uffd monitor to
distinguish this case from other error conditions.

Unfortunately I overlooked userfaultfd_zeropage when updating
userfaultd_copy().

Link: http://lkml.kernel.org/r/1501136819-21857-1-git-send-email-rppt@linux.vnet.ibm.com
Fixes: 96333187 ("userfaultfd_copy: return -ENOSPC in case mm has gone")
Signed-off-by: NMike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Andre Wild reported the following warning:

  WARNING: CPU: 2 PID: 1205 at kernel/cpu.c:240 lockdep_assert_cpus_held+0x4c/0x60
  Modules linked in:
  CPU: 2 PID: 1205 Comm: bash Not tainted 4.13.0-rc2-00022-gfd2b2c57 #10
  Hardware name: IBM 2964 N96 702 (z/VM 6.4.0)
  task: 00000000701d8100 task.stack: 0000000073594000
  Krnl PSW : 0704f00180000000 0000000000145e24 (lockdep_assert_cpus_held+0x4c/0x60)
  ...
  Call Trace:
   lockdep_assert_cpus_held+0x42/0x60)
   stop_machine_cpuslocked+0x62/0xf0
   build_all_zonelists+0x92/0x150
   numa_zonelist_order_handler+0x102/0x150
   proc_sys_call_handler.isra.12+0xda/0x118
   proc_sys_write+0x34/0x48
   __vfs_write+0x3c/0x178
   vfs_write+0xbc/0x1a0
   SyS_write+0x66/0xc0
   system_call+0xc4/0x2b0
   locks held by bash/1205:
   #0:  (sb_writers#4){.+.+.+}, at: vfs_write+0xa6/0x1a0
   #1:  (zl_order_mutex){+.+...}, at: numa_zonelist_order_handler+0x44/0x150
   #2:  (zonelists_mutex){+.+...}, at: numa_zonelist_order_handler+0xf4/0x150
  Last Breaking-Event-Address:
    lockdep_assert_cpus_held+0x48/0x60

This can be easily triggered with e.g.

    echo n > /proc/sys/vm/numa_zonelist_order

In commit 3f906ba2 ("mm/memory-hotplug: switch locking to a percpu
rwsem") memory hotplug locking was changed to fix a potential deadlock.

This also switched the stop_machine() invocation within
build_all_zonelists() to stop_machine_cpuslocked() which now expects
that online cpus are locked when being called.

This assumption is not true if build_all_zonelists() is being called
from numa_zonelist_order_handler().

In order to fix this simply add a mem_hotplug_begin()/mem_hotplug_done()
pair to numa_zonelist_order_handler().

Link: http://lkml.kernel.org/r/20170726111738.38768-1-heiko.carstens@de.ibm.com
Fixes: 3f906ba2 ("mm/memory-hotplug: switch locking to a percpu rwsem")
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: NAndre Wild <wild@linux.vnet.ibm.com>
Acked-by: NMichal Hocko <mhocko@suse.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a thread is OOM-killed during swap_readpage() operation, an oops
occurs because end_swap_bio_read() is calling wake_up_process() based on
an assumption that the thread which called swap_readpage() is still
alive.

  Out of memory: Kill process 525 (polkitd) score 0 or sacrifice child
  Killed process 525 (polkitd) total-vm:528128kB, anon-rss:0kB, file-rss:4kB, shmem-rss:0kB
  oom_reaper: reaped process 525 (polkitd), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
  general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
  Modules linked in: nf_conntrack_netbios_ns nf_conntrack_broadcast ip6t_rpfilter ipt_REJECT nf_reject_ipv4 ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter coretemp ppdev pcspkr vmw_balloon sg shpchp vmw_vmci parport_pc parport i2c_piix4 ip_tables xfs libcrc32c sd_mod sr_mod cdrom ata_generic pata_acpi vmwgfx ahci libahci drm_kms_helper ata_piix syscopyarea sysfillrect sysimgblt fb_sys_fops mptspi scsi_transport_spi ttm e1000 mptscsih drm mptbase i2c_core libata serio_raw
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.0-rc2-next-20170725 #129
  Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/31/2013
  task: ffffffffb7c16500 task.stack: ffffffffb7c00000
  RIP: 0010:__lock_acquire+0x151/0x12f0
  Call Trace:
   <IRQ>
   lock_acquire+0x59/0x80
   _raw_spin_lock_irqsave+0x3b/0x4f
   try_to_wake_up+0x3b/0x410
   wake_up_process+0x10/0x20
   end_swap_bio_read+0x6f/0xf0
   bio_endio+0x92/0xb0
   blk_update_request+0x88/0x270
   scsi_end_request+0x32/0x1c0
   scsi_io_completion+0x209/0x680
   scsi_finish_command+0xd4/0x120
   scsi_softirq_done+0x120/0x140
   __blk_mq_complete_request_remote+0xe/0x10
   flush_smp_call_function_queue+0x51/0x120
   generic_smp_call_function_single_interrupt+0xe/0x20
   smp_trace_call_function_single_interrupt+0x22/0x30
   smp_call_function_single_interrupt+0x9/0x10
   call_function_single_interrupt+0xa7/0xb0
   </IRQ>
  RIP: 0010:native_safe_halt+0x6/0x10
   default_idle+0xe/0x20
   arch_cpu_idle+0xa/0x10
   default_idle_call+0x1e/0x30
   do_idle+0x187/0x200
   cpu_startup_entry+0x6e/0x70
   rest_init+0xd0/0xe0
   start_kernel+0x456/0x477
   x86_64_start_reservations+0x24/0x26
   x86_64_start_kernel+0xf7/0x11a
   secondary_startup_64+0xa5/0xa5
  Code: c3 49 81 3f 20 9e 0b b8 41 bc 00 00 00 00 44 0f 45 e2 83 fe 01 0f 87 62 ff ff ff 89 f0 49 8b 44 c7 08 48 85 c0 0f 84 52 ff ff ff <f0> ff 80 98 01 00 00 8b 3d 5a 49 c4 01 45 8b b3 18 0c 00 00 85
  RIP: __lock_acquire+0x151/0x12f0 RSP: ffffa01f39e03c50
  ---[ end trace 6c441db499169b1e ]---
  Kernel panic - not syncing: Fatal exception in interrupt
  Kernel Offset: 0x36000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
  ---[ end Kernel panic - not syncing: Fatal exception in interrupt

Fix it by holding a reference to the thread.

[akpm@linux-foundation.org: add comment]
Fixes: 23955622 ("swap: add block io poll in swapin path")
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: NShaohua Li <shli@fb.com>
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mike reported kernel goes oops with ltp:zram03 testcase.

  zram: Added device: zram0
  zram0: detected capacity change from 0 to 107374182400
  BUG: unable to handle kernel paging request at 0000306d61727a77
  IP: zs_map_object+0xb9/0x260
  PGD 0
  P4D 0
  Oops: 0000 [#1] SMP
  Dumping ftrace buffer:
     (ftrace buffer empty)
  Modules linked in: zram(E) xfs(E) libcrc32c(E) btrfs(E) xor(E) raid6_pq(E) loop(E) ebtable_filter(E) ebtables(E) ip6table_filter(E) ip6_tables(E) iptable_filter(E) ip_tables(E) x_tables(E) af_packet(E) br_netfilter(E) bridge(E) stp(E) llc(E) iscsi_ibft(E) iscsi_boot_sysfs(E) nls_iso8859_1(E) nls_cp437(E) vfat(E) fat(E) intel_powerclamp(E) coretemp(E) cdc_ether(E) kvm_intel(E) usbnet(E) mii(E) kvm(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) crc32c_intel(E) iTCO_wdt(E) ghash_clmulni_intel(E) bnx2(E) iTCO_vendor_support(E) pcbc(E) ioatdma(E) ipmi_ssif(E) aesni_intel(E) i5500_temp(E) i2c_i801(E) aes_x86_64(E) lpc_ich(E) shpchp(E) mfd_core(E) crypto_simd(E) i7core_edac(E) dca(E) glue_helper(E) cryptd(E) ipmi_si(E) button(E) acpi_cpufreq(E) ipmi_devintf(E) pcspkr(E) ipmi_msghandler(E)
   nfsd(E) auth_rpcgss(E) nfs_acl(E) lockd(E) grace(E) sunrpc(E) ext4(E) crc16(E) mbcache(E) jbd2(E) sd_mod(E) ata_generic(E) i2c_algo_bit(E) ata_piix(E) drm_kms_helper(E) ahci(E) syscopyarea(E) sysfillrect(E) libahci(E) sysimgblt(E) fb_sys_fops(E) uhci_hcd(E) ehci_pci(E) ttm(E) ehci_hcd(E) libata(E) drm(E) megaraid_sas(E) usbcore(E) sg(E) dm_multipath(E) dm_mod(E) scsi_dh_rdac(E) scsi_dh_emc(E) scsi_dh_alua(E) scsi_mod(E) efivarfs(E) autofs4(E) [last unloaded: zram]
  CPU: 6 PID: 12356 Comm: swapon Tainted: G            E   4.13.0.g87b2c3fc-default #194
  Hardware name: IBM System x3550 M3 -[7944K3G]-/69Y5698     , BIOS -[D6E150AUS-1.10]- 12/15/2010
  task: ffff880158d2c4c0 task.stack: ffffc90001680000
  RIP: 0010:zs_map_object+0xb9/0x260
  Call Trace:
   zram_bvec_rw.isra.26+0xe8/0x780 [zram]
   zram_rw_page+0x6e/0xa0 [zram]
   bdev_read_page+0x81/0xb0
   do_mpage_readpage+0x51a/0x710
   mpage_readpages+0x122/0x1a0
   blkdev_readpages+0x1d/0x20
   __do_page_cache_readahead+0x1b2/0x270
   ondemand_readahead+0x180/0x2c0
   page_cache_sync_readahead+0x31/0x50
   generic_file_read_iter+0x7e7/0xaf0
   blkdev_read_iter+0x37/0x40
   __vfs_read+0xce/0x140
   vfs_read+0x9e/0x150
   SyS_read+0x46/0xa0
   entry_SYSCALL_64_fastpath+0x1a/0xa5
  Code: 81 e6 00 c0 3f 00 81 fe 00 00 16 00 0f 85 9f 01 00 00 0f b7 13 65 ff 05 5e 07 dc 7e 66 c1 ea 02 81 e2 ff 01 00 00 49 8b 54 d4 08 <8b> 4a 48 41 0f af ce 81 e1 ff 0f 00 00 41 89 c9 48 c7 c3 a0 70
  RIP: zs_map_object+0xb9/0x260 RSP: ffffc90001683988
  CR2: 0000306d61727a77

He bisected the problem is [1].

After commit cf8e0fed ("mm/zsmalloc: simplify zs_max_alloc_size
handling"), zram doesn't use double pointer for pool->size_class any
more in zs_create_pool so counter function zs_destroy_pool don't need to
free it, either.

Otherwise, it does kfree wrong address and then, kernel goes Oops.

Link: http://lkml.kernel.org/r/20170725062650.GA12134@bbox
Fixes: cf8e0fed ("mm/zsmalloc: simplify zs_max_alloc_size handling")
Signed-off-by: NMinchan Kim <minchan@kernel.org>
Reported-by: NMike Galbraith <efault@gmx.de>
Tested-by: NMike Galbraith <efault@gmx.de>
Reviewed-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The kerneldoc comment for kthread_create() had an incorrect argument
name, leading to a warning in the docs build.

Correct it, and make one more small step toward a warning-free build.

Link: http://lkml.kernel.org/r/20170724135916.7f486c6f@lwn.netSigned-off-by: NJonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

gcc-7 produces this warning:

  mm/kasan/report.c: In function 'kasan_report':
  mm/kasan/report.c:351:3: error: 'info.first_bad_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
     print_shadow_for_address(info->first_bad_addr);
     ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  mm/kasan/report.c:360:27: note: 'info.first_bad_addr' was declared here

The code seems fine as we only print info.first_bad_addr when there is a
shadow, and we always initialize it in that case, but this is relatively
hard for gcc to figure out after the latest rework.

Adding an intialization to the most likely value together with the other
struct members shuts up that warning.

Fixes: b235b9808664 ("kasan: unify report headers")
Link: https://patchwork.kernel.org/patch/9641417/
Link: http://lkml.kernel.org/r/20170725152739.4176967-1-arnd@arndb.deSigned-off-by: NArnd Bergmann <arnd@arndb.de>
Suggested-by: NAlexander Potapenko <glider@google.com>
Suggested-by: NAndrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: NAndrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When mremap is called with MREMAP_FIXED it unmaps memory at the
destination address without notifying userfaultfd monitor.

If the destination were registered with userfaultfd, the monitor has no
way to distinguish between the old and new ranges and to properly relate
the page faults that would occur in the destination region.

Fixes: 897ab3e0 ("userfaultfd: non-cooperative: add event for memory unmaps")
Link: http://lkml.kernel.org/r/1500276876-3350-1-git-send-email-rppt@linux.vnet.ibm.comSigned-off-by: NMike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: NPavel Emelyanov <xemul@virtuozzo.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Nadav Amit identified a theoritical race between page reclaim and
mprotect due to TLB flushes being batched outside of the PTL being held.

He described the race as follows:

        CPU0                            CPU1
        ----                            ----
                                        user accesses memory using RW PTE
                                        [PTE now cached in TLB]
        try_to_unmap_one()
        ==> ptep_get_and_clear()
        ==> set_tlb_ubc_flush_pending()
                                        mprotect(addr, PROT_READ)
                                        ==> change_pte_range()
                                        ==> [ PTE non-present - no flush ]

                                        user writes using cached RW PTE
        ...

        try_to_unmap_flush()

The same type of race exists for reads when protecting for PROT_NONE and
also exists for operations that can leave an old TLB entry behind such
as munmap, mremap and madvise.

For some operations like mprotect, it's not necessarily a data integrity
issue but it is a correctness issue as there is a window where an
mprotect that limits access still allows access.  For munmap, it's
potentially a data integrity issue although the race is massive as an
munmap, mmap and return to userspace must all complete between the
window when reclaim drops the PTL and flushes the TLB.  However, it's
theoritically possible so handle this issue by flushing the mm if
reclaim is potentially currently batching TLB flushes.

Other instances where a flush is required for a present pte should be ok
as either the page lock is held preventing parallel reclaim or a page
reference count is elevated preventing a parallel free leading to
corruption.  In the case of page_mkclean there isn't an obvious path
that userspace could take advantage of without using the operations that
are guarded by this patch.  Other users such as gup as a race with
reclaim looks just at PTEs.  huge page variants should be ok as they
don't race with reclaim.  mincore only looks at PTEs.  userfault also
should be ok as if a parallel reclaim takes place, it will either fault
the page back in or read some of the data before the flush occurs
triggering a fault.

Note that a variant of this patch was acked by Andy Lutomirski but this
was for the x86 parts on top of his PCID work which didn't make the 4.13
merge window as expected.  His ack is dropped from this version and
there will be a follow-on patch on top of PCID that will include his
ack.

[akpm@linux-foundation.org: tweak comments]
[akpm@linux-foundation.org: fix spello]
Link: http://lkml.kernel.org/r/20170717155523.emckq2esjro6hf3z@suse.deReported-by: NNadav Amit <nadav.amit@gmail.com>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: <stable@vger.kernel.org>	[v4.4+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After commit 3d375d78 ("mm: update callers to use HASH_ZERO flag"),
drop unused pidhash_size in pidhash_init().

Link: http://lkml.kernel.org/r/1500389267-49222-1-git-send-email-wangkefeng.wang@huawei.comSigned-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: NPavel Tatashin <Pasha.Tatashin@Oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 9a291a7c ("mm/hugetlb: report -EHWPOISON not -EFAULT when
FOLL_HWPOISON is specified") causes __get_user_pages to ignore certain
errors from follow_hugetlb_page.  After such error, __get_user_pages
subsequently calls faultin_page on the same VMA and start address that
follow_hugetlb_page failed on instead of returning the error immediately
as it should.

In follow_hugetlb_page, when hugetlb_fault returns a value covered under
VM_FAULT_ERROR, follow_hugetlb_page returns it without setting nr_pages
to 0 as __get_user_pages expects in this case, which causes the
following to happen in __get_user_pages: the "while (nr_pages)" check
succeeds, we skip the "if (!vma..." check because we got a VMA the last
time around, we find no page with follow_page_mask, and we call
faultin_page, which calls hugetlb_fault for the second time.

This issue also slightly changes how __get_user_pages works.  Before, it
only returned error if it had made no progress (i = 0).  But now,
follow_hugetlb_page can clobber "i" with an error code since its new
return path doesn't check for progress.  So if "i" is nonzero before a
failing call to follow_hugetlb_page, that indication of progress is lost
and __get_user_pages can return error even if some pages were
successfully pinned.

To fix this, change follow_hugetlb_page so that it updates nr_pages,
allowing __get_user_pages to fail immediately and restoring the "error
only if no progress" behavior to __get_user_pages.

Tested that __get_user_pages returns when expected on error from
hugetlb_fault in follow_hugetlb_page.

Fixes: 9a291a7c ("mm/hugetlb: report -EHWPOISON not -EFAULT when FOLL_HWPOISON is specified")
Link: http://lkml.kernel.org/r/1500406795-58462-1-git-send-email-daniel.m.jordan@oracle.comSigned-off-by: NDaniel Jordan <daniel.m.jordan@oracle.com>
Acked-by: NPunit Agrawal <punit.agrawal@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: James Morse <james.morse@arm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: <stable@vger.kernel.org>	[4.12.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull x86 platform driver fixes from Darren Hart:
 "Fix two bugs under error or abnormal usage conditions. Correct a
  config dependency:

  dell-wmi:
   - Fix driver interface version query

  wmi:
   - Fix error handling in acpi_wmi_init()

  peaq-wmi:
   - select INPUT_POLLDEV"

* tag 'platform-drivers-x86-v4.13-3' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: dell-wmi: Fix driver interface version query
  platform/x86: wmi: Fix error handling in acpi_wmi_init()
  platform/x86: peaq-wmi: select INPUT_POLLDEV

Pull SCSI fixes from James Bottomley:
 "These seven patches are mostly minor build, Kconfig and error leg
  fixes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qedi: Fix return code in qedi_ep_connect()
  scsi: lpfc: fix linking against modular NVMe support
  scsi: scsi_transport_fc: return -EBUSY for deleted vport
  scsi: libcxgbi: add check for valid cxgbi_task_data
  scsi: aic7xxx: fix firmware build with O=path
  scsi: megaraid_sas: fix memleak in megasas_alloc_cmdlist_fusion
  scsi: qedi: Add ISCSI_BOOT_SYSFS to Kconfig

rpc_clnt_add_xprt() expects the callback function to be synchronous, and
expects to release the transport and switch references itself.

Fixes: 04fa2c6b ("NFS pnfs data server multipath session trunking")
Signed-off-by: NTrond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>

of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Freescale MPC832x RDB board
code still only regards 0 as a failure indication -- fix it up.

Fixes: 7a4228bb ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NScott Wood <oss@buserror.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When I converted dell-wmi to the new bus infrastructure, I left the
call to dell_wmi_check_descriptor_buffer() in dell_wmi_init().  This
could cause two problems:

 - An error message when loading the driver on a system without
   dell-wmi.  We'd try to read the event descriptor even if the WMI
   GUID wasn't there.

 - A possible race if dell-wmi was loaded manually before wmi was
   fully initialized.

Fix it by moving the call to the probe function where it belongs.

Fixes: bff589be ("platform/x86: dell-wmi: Convert to the WMI bus infrastructure")
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Reviewed-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDarren Hart (VMware) <dvhart@infradead.org>

The verifier is allocated on the stack, but the EXCHANGE_ID RPC call was
changed to be asynchronous by commit 8d89bd70. If we interrrupt
the call to rpc_wait_for_completion_task(), we can therefore end up
transmitting random stack contents in lieu of the verifier.

Fixes: 8d89bd70 ("NFS setup async exchange_id")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: NTrond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>

Pull parsic fixes from Helge Deller:

 - Our cache flushing code ran into a BUG in case context is not
   current. Fix it by flushing the whole cache in such rare situations
   (by Dave Anglin).

 - Fix a "sleeping function called from invalid context BUG" in our
   pdc_stable driver by rearranging our locks (by James Bottomley)

 - The thread and irq stacks require more than 16 KB since kernel 4.11.
   Increase both to 32 KB.

 - Define CONFIG_CPU_BIG_ENDIAN unconditionally on parisc to avoid wrong
   behaviour in qrwlock functions (by Babu Moger).

* 'parisc-4.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Define CONFIG_CPU_BIG_ENDIAN
  parisc: pdc_stable: Fix locking when creating sysfs links
  parisc: Increase thread and stack size to 32kb
  parisc: Handle vma's whose context is not current in flush_cache_range

Pull networking fixes from David Miller:

 1) Handle notifier registry failures properly in tun/tap driver, from
    Tonghao Zhang.

 2) Fix bpf verifier handling of subtraction bounds and add a testcase
    for this, from Edward Cree.

 3) Increase reset timeout in ftgmac100 driver, from Ben Herrenschmidt.

 4) Fix use after free in prd_retire_rx_blk_timer_exired() in AF_PACKET,
    from Cong Wang.

 5) Fix SElinux regression due to recent UDP optimizations, from Paolo
    Abeni.

 6) We accidently increment IPSTATS_MIB_FRAGFAILS in the ipv6 code
    paths, fix from Stefano Brivio.

 7) Fix some mem leaks in dccp, from Xin Long.

 8) Adjust MDIO_BUS kconfig deps to avoid build errors, from Arnd
    Bergmann.

 9) Mac address length check and buffer size fixes from Cong Wang.

10) Don't leak sockets in ipv6 udp early demux, from Paolo Abeni.

11) Fix return value when copy_from_user() fails in
    bpf_prog_get_info_by_fd(), from Daniel Borkmann.

12) Handle PHY_HALTED properly in phy library state machine, from
    Florian Fainelli.

13) Fix OOPS in fib_sync_down_dev(), from Ido Schimmel.

14) Fix truesize calculation in virtio_net which led to performance
    regressions, from Michael S Tsirkin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  samples/bpf: fix bpf tunnel cleanup
  udp6: fix jumbogram reception
  ppp: Fix a scheduling-while-atomic bug in del_chan
  Revert "net: bcmgenet: Remove init parameter from bcmgenet_mii_config"
  virtio_net: fix truesize for mergeable buffers
  mv643xx_eth: fix of_irq_to_resource() error check
  MAINTAINERS: Add more files to the PHY LIBRARY section
  ipv4: fib: Fix NULL pointer deref during fib_sync_down_dev()
  net: phy: Correctly process PHY_HALTED in phy_stop_machine()
  sunhme: fix up GREG_STAT and GREG_IMASK register offsets
  bpf: fix bpf_prog_get_info_by_fd to dump correct xlated_prog_len
  tcp: avoid bogus gcc-7 array-bounds warning
  net: tc35815: fix spelling mistake: "Intterrupt" -> "Interrupt"
  bpf: don't indicate success when copy_from_user fails
  udp6: fix socket leak on early demux
  net: thunderx: Fix BGX transmit stall due to underflow
  Revert "vhost: cache used event for better performance"
  team: use a larger struct for mac address
  net: check dev->addr_len for dev_set_mac_address()
  phy: bcm-ns-usb3: fix MDIO_BUS dependency
  ...

test_tunnel_bpf.sh fails to remove the vxlan11 tunnel device, causing the
next geneve tunnelling test case fails.  In addition, the geneve reserved bit
in tcbpf2_kern.c should be zero, according to the RFC.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 67a51780 ("ipv6: udp: leverage scratch area
helpers") udp6_recvmsg() read the skb len from the scratch area,
to avoid a cache miss.
But the UDP6 rx path support RFC 2675 UDPv6 jumbograms, and their
length exceeds the 16 bits available in the scratch area. As a side
effect the length returned by recvmsg() is:
<ingress datagram len> % (1<<16)

This commit addresses the issue allocating one more bit in the
IP6CB flags field and setting it for incoming jumbograms.
Such field is still in the first cacheline, so at recvmsg()
time we can check it and fallback to access skb->len if
required, without a measurable overhead.

Fixes: 67a51780 ("ipv6: udp: leverage scratch area helpers")
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PPTP set the pptp_sock_destruct as the sock's sk_destruct, it would
trigger this bug when __sk_free is invoked in atomic context, because of
the call path pptp_sock_destruct->del_chan->synchronize_rcu.

Now move the synchronize_rcu to pptp_release from del_chan. This is the
only one case which would free the sock and need the synchronize_rcu.

The following is the panic I met with kernel 3.3.8, but this issue should
exist in current kernel too according to the codes.

BUG: scheduling while atomic
__schedule_bug+0x5e/0x64
__schedule+0x55/0x580
? ppp_unregister_channel+0x1cd5/0x1de0 [ppp_generic]
? dev_hard_start_xmit+0x423/0x530
? sch_direct_xmit+0x73/0x170
__cond_resched+0x16/0x30
_cond_resched+0x22/0x30
wait_for_common+0x18/0x110
? call_rcu_bh+0x10/0x10
wait_for_completion+0x12/0x20
wait_rcu_gp+0x34/0x40
? wait_rcu_gp+0x40/0x40
synchronize_sched+0x1e/0x20
0xf8417298
0xf8417484
? sock_queue_rcv_skb+0x109/0x130
__sk_free+0x16/0x110
? udp_queue_rcv_skb+0x1f2/0x290
sk_free+0x16/0x20
__udp4_lib_rcv+0x3b8/0x650
Signed-off-by: NGao Feng <gfree.wind@vip.163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 28b45910 ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.

Fixes: 28b45910 ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Seth Forshee noticed a performance degradation with some workloads.
This turns out to be due to packet drops.  Euan Kemp noticed that this
is because we drop all packets where length exceeds the truesize, but
for some packets we add in extra memory without updating the truesize.
This in turn was kept around unchanged from ab7db917 ("virtio-net:
auto-tune mergeable rx buffer size for improved performance").  That
commit had an internal reason not to account for the extra space: not
enough bits to do it.  No longer true so let's account for the allocated
length exactly.

Many thanks to Seth Forshee for the report and bisecting and Euan Kemp
for debugging the issue.

Fixes: 680557cf ("virtio_net: rework mergeable buffer handling")
Reported-by: NEuan Kemp <euan.kemp@coreos.com>
Tested-by: NEuan Kemp <euan.kemp@coreos.com>
Reported-by: NSeth Forshee <seth.forshee@canonical.com>
Tested-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>