IF freq	for DVB-T 7 MHz	and 8 MHz was set slightly wrong. Due to that it
didn't worked at all (?) for 7 MHz channels and most likely performance
was dropped for 8 MHz channels.

That bug was pointed by few people during last two months. Thank you.

Trivial fix. Compile tested only due to lack of proper HW and signal.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: Romolo Manfredini <romoloman@hotmail.com>
Cc: Alireza Moini <alireza.moini@silverbrookresearch.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The radio-gemtek-pci driver is for the same hardware as the radio-maxiradio
driver which uses the same GemTek PR103 and tea5757 combination and the two
drivers are identical. I chose the maxiradio over the gemtek-pci driver since
the maxiradio has support for mono/stereo detection.

Tested with my gemtek-pci card.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the standard USA/Europe frequency range of 87-108 MHz instead of the
arbitrary 50-150 MHz.

Copied from the radio-gemtek-pci driver which supports the same hardware.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

vpif_display now uses .unlocked_ioctl instead of .ioctl.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now uses .unlocked_ioctl instead of .ioctl.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NMurali Karicheri <mkaricheri@gmail.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added functions to set and get custom DV timings.
Signed-off-by: NMats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- Added functions to set/get/query/enum DV presets for vpif_caputre and
  vpif_display.
- The format specification table is extended with all the DV formats
  supported by TVP7002.
Signed-off-by: NMats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- The ch_params tables in vpif_capture.c and vpif_display.c are moved to a common
  table in vpif.c. Then it is easier to maintain the table.
- The field "fps" is removed from the struct vpif_channel_config_params because it
  is not used.
Signed-off-by: NMats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by : Murali Karicheri <mkaricheri@gmail.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The following functions are added to the drivers:
    - vpif_g_chip_ident
    - vpif_dbg_g_register
    - vpif_dbg_s_register
    - vpif_log_status
Signed-off-by: NMats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Implement core-assisted locking in cpia2.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert saa7146 to use core-assisted locking.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since tda9875 is part of tvaudio this field no longer makes sense. Remove it.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In commit 411674fd the tda9875 support was
added to tvaudio. This means that tda9875 is no longer used since mid-2009.

If there are out-of-tree users of this driver, then they can switch to tvaudio
instead.

The original commit message read as follows:

    This change allows bttv to use tvaudio for this device. Since this device
    has the same i2c address as the tda9874 we need to support both in the same
    tvaudio driver. This makes it possible for tvaudio to detect which chip is
    used. Originally the tda9875 was only available in the dedicated tda9875
    driver, but that makes life very hard for bttv since loading tvaudio might
    misdetect a tda9875 as a tda9874.

So there were good reasons for moving the tda9875 code into tvaudio.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (lm93) Add support for LM94

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: Validate cpu early in perf_event_alloc()
  perf: Find_get_context: fix the per-cpu-counter check
  perf: Fix contexted inheritance

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Clear irqstack thread_info
  x86: Make relocatable kernel work with new binutils

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
  MIPS: Malta: enable Cirrus FB console
  MIPS: add CONFIG_VIRTUALIZATION for virtio support
  MIPS: Implement __read_mostly
  MIPS: ath79: add common WMAC device for AR913X based boards
  MIPS: ath79: Add initial support for the Atheros AP81 reference board
  MIPS: ath79: add common SPI controller device
  SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
  MIPS: ath79: add common GPIO buttons device
  MIPS: ath79: add common watchdog device
  MIPS: ath79: add common GPIO LEDs device
  MIPS: ath79: add initial support for the Atheros PB44 reference board
  MIPS: ath79: utilize the MIPS multi-machine support
  MIPS: ath79: add GPIOLIB support
  MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
  MIPS: jump label: Add MIPS support.
  MIPS: Use WARN() in uasm for better diagnostics.
  MIPS: Optimize TLB handlers for Octeon CPUs
  MIPS: Add LDX and LWX instructions to uasm.
  MIPS: Use BBIT instructions in TLB handlers
  MIPS: Declare uasm bbit0 and bbit1 functions.
  ...

This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

Starting from perf_event_alloc()->perf_init_event(), the kernel
assumes that event->cpu is either -1 or the valid CPU number.

Change perf_event_alloc() to validate this argument early. This
also means we can remove the similar check in
find_get_context().
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: gregkh@suse.de
Cc: stable@kernel.org
LKML-Reference: <20110118161032.GC693@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

If task == NULL, find_get_context() should always check that cpu
is correct.

Afaics, the bug was introduced by 38a81da2 "perf events: Clean
up pid passing", but even before that commit "&& cpu != -1" was
not exactly right, -ESRCH from find_task_by_vpid() is not
accurate.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: gregkh@suse.de
Cc: stable@kernel.org
LKML-Reference: <20110118161008.GB693@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

While most users of a physical Malta board are using the serial port
as the console, a lot of QEMU users would prefer to interact with a
graphical console. Enable the Cirrus FB support in the Malta default
configuration to make that possible. Note that the default console will
still be the serial port, users have to pass "console=tty0" to the
kernel to use the Cirrus FB.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2001/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add CONFIG_VIRTUALIZATION to the MIPS architecture and include the
the virtio code there. Used to enable the virtio drivers under QEMU.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2002/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Just do what everyone else is doing by placing __read_mostly things in
the .data.read_mostly section.

mips_io_port_base can not be read-only (const) and writable
(__read_mostly) at the same time.  One of them has to go, so I chose
to eliminate the __read_mostly.  It will still get stuck in a portion
of memory that is not adjacent to things that are written, and thus
not be on a dirty cache line, for whatever that is worth.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1702/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add common platform_device and helper code to make the registration
of the built-in wireless MAC easier on the Atheros AR9130/AR9132
based boards. Also register the WMAC device on the AR81 board.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>,
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1962/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1952/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Several boards are using the built-in SPI controller of the
AR71XX/AR724X/AR913X SoCs. This patch adds common platform_device
and helper code to register it. Additionally, the patch registers
the SPI bus on the PB44 board.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1956/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Almost all boards have one or more push buttons connected to GPIO lines.
This patch adds common code to register a platform_device for them.

The patch also adds support for the buttons on the PB44 board.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1954/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All supported SoCs have a built-in hardware watchdog driver. This patch
registers a platform_device for that to make it usable.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1955/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Almost all boards have one or more LEDs connected to GPIO lines. This
patch adds common code to register a platform_device for them.

The patch also adds support for the LEDs on the PB44 board.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1953/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1950/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1949/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch implements generic GPIO routines for the built-in
GPIO controllers of the Atheros AR71XX/AR724X/AR913X SoCs.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1948/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds initial support for various Atheros SoCs based on the
MIPS 24Kc core. The following models are supported at the moment:

  - AR7130
  - AR7141
  - AR7161
  - AR9130
  - AR9132
  - AR7240
  - AR7241
  - AR7242

The current patch contains minimal support only, but the resulting
kernel can boot into user-space with using of an initramfs image on
various boards which are using these SoCs. Support for more built-in
devices and individual boards will be implemented in further patches.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1947/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In order not to be left behind, we add jump label support for MIPS.

Tested on 64-bit big endian (Octeon), and 32-bit little endian
(malta/qemu).
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/1923/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On the off chance that uasm ever warns about overflow, there is no way
to know what the offending instruction is.

Change the printks to WARNs, so we can get a nice stack trace.  It has
the added benefit of being much more noticeable than the short single
line warning message, so is less likely to be ignored.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1905/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Octeon can use scratch registers in the TLB handlers.  Octeon II can
use LDX instructions.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1904/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Needed by Octeon II optimized TLB handlers.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Pachwork: https://patchwork.linux-mips.org/patch/1903/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>