- 16 7月, 2014 1 次提交
-
-
由 Edward Cree 提交于
Added a counter rx_noskb_drop for failure to allocate an skb. Summed the per-channel rx_nodesc_trunc counters earlier so that they can be included in rx_dropped. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 4月, 2014 1 次提交
-
-
由 Edward Cree 提交于
When an MCDI command times out (whether or not we find it completed when we poll), call efx_mcdi_abandon(), which tells all subsequent MCDI calls to fail-fast, and queues up an FLR. Because an FLR doesn't lead to receiving any reboot even from the MC (unlike most other types of reset), we have to call efx_ef10_reset_mc_allocations. In efx_start_all(), if a reset (of any kind) is pending, we bail out. Without this, attempts to reconfigure (e.g. change mtu) can cause driver/mc state inconsistency if the first MCDI call triggers an FLR. For similar reasons, on EF10, in efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number of active queues to zero before calling efx_stop_all(). And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT), set active_queues and flushes pending & outstanding to zero. efx_mcdi_mode_{poll,event}() should not take us out of fail-fast mode. Instead, this is done by efx_mcdi_reset() after the FLR completes. The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really fit into the hierarchy of reset 'scopes' whereby efx_reset() decides some resets subsume others. Thus, it uses separate logic. Also, fixed up some inconsistency around RESET_TYPE_MC_BIST, which was in the wrong place in that hierarchy. Signed-off-by: NShradha Shah <sshah@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 12月, 2013 4 次提交
-
-
由 Andrew Rybchenko 提交于
The EF10 implementation already does this, and it makes more logical sense to group the RSS hash key and indirection table together. Rename the operation to rx_push_rss_config. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Daniel Pieczko 提交于
I added efx_ptp_get_mode() to avoid moving the definition for efx_ptp_data, since the current PTP mode is needed for siena.c:siena_set_ptp_hwtstamp. [bwh: Also move the rx_filters mask, and add kernel-doc] Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
We need a dedicated channel on Siena to ensure we can match up the separate RX and timestamp events for each PTP packet. We won't do this for EF10 as timestamps are delivered inline. Pass a channel index of 0 to MC_CMD_PTP_OP_ENABLE when there is no dedicated channel. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Jon Cooper 提交于
We don't directly control RX ingress on Siena or any later controllers, and so we cannot prevent packets from entering the RX datapath while the RX queues are not set up. This results in the hardware incrementing RX_NODESC_DROP_CNT, but it's not an error and we should not include it in error stats. When bringing an interface up or down, pull (or wait for) stats and count the number of packets that were dropped while the interface was down. Subtract this from the reported RX dropped count. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 30 8月, 2013 3 次提交
-
-
由 Ben Hutchings 提交于
Update the dates for files that have been added to in 2012-2013. Drop the 'Solarstorm' brand name that's still lingering here. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
This should be done during MCDI initialisation for any NIC. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 28 8月, 2013 4 次提交
-
-
由 Jon Cooper 提交于
EF10 uses an entirely different RX prefix format from Falcon-arch. Extend struct efx_nic_type to describe this. [bwh: Also replace the magic numbers used for the Falcon-arch RX prefix] Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Laurence Evans 提交于
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Various hardware statistics that are available for Siena are unavailable or meaningless for Falcon. Huntington adds further to the NIC-type-specific statistics, as it has different MAC blocks from Falcon/Siena. All NIC types still provide most statistics by DMA, and use little-endian byte order. Therefore: 1. Add some general utility functions for reporting hardware statistics, efx_nic_describe_stats() and efx_nic_update_stats(). 2. Add an efx_nic_type::describe_stats operation to get the number and names of statistics, implemented using efx_nic_describe_stats() 3. Change efx_nic_type::update_stats to store the core statistics (struct rtnl_link_stats64) or full statistics (array of u64) in a caller-provided buffer. Use efx_nic_update_stats() to aid in the implementation. 4. Rename struct efx_ethtool_stat to struct efx_sw_stat_desc and EFX_ETHTOOL_NUM_STATS to EFX_ETHTOOL_SW_STAT_COUNT. 5. Remove efx_nic::mac_stats and struct efx_mac_stats. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Merge the per-NIC-type MTD probe selection and struct efx_mtd_ops into struct efx_nic_type. Move the implementations into the appropriate source files. Several NVRAM functions are now only called from MTD operations which are now implemented in the same file (falcon.c or mcdi.c). There is no need for them to be extern, or to be defined at all if CONFIG_SFC_MTD is not enabled, so move them into the #ifdef CONFIG_SFC_MTD sections in those files. Most of the SPI-related definitions are also only used in falcon.c, so move them there. Put the remainder of spi.h into nic.h (which previously included it). Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 23 8月, 2013 2 次提交
-
-
由 Ben Hutchings 提交于
On Falcon we implement MAC filtering requested by the stack using the MAC wrapper's single unicast filter and multicast hash filter. Siena is very similar, though MAC configuration is mediated by the MC. Since MCDI operations may sleep, reconfiguration is deferred from ndo_set_rx_mode to a work item. However, it still updates the private variables describing the filter state synchronously. Contrary to comments, the later use of these variables is not protected using the address lock, resulting in race conditions. Move the state update to a new function efx_farch_filter_sync_rx_mode() and make the Falcon-arch MAC configuration functions call that, so that its use is consistently serialised by the mac_lock. Invert and rename the promiscuous flag to the more accurate unicast_filter, and comment that both this and multicast_hash are not used on EF10. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Aside from accelerated RFS, there is almost nothing that can be shared between the filter table implementations for the Falcon architecture and EF10. Move the few shared functions into efx.c and rx.c and the rest into farch.c. Introduce efx_nic_type operations for the implementation and inline wrapper functions that call these. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 22 8月, 2013 11 次提交
-
-
由 Ben Hutchings 提交于
EF10 functions don't have a fixed BAR size, and the minimum is not large enough for all the queues we might want to allocate. We have to find out the BAR size at run-time, and therefore phys_addr_channels and mem_map_size cannot be defined per-NIC-type. Change efx_nic_type::mem_map_size to a function pointer which is called to find the wanted memory map size (before probe). Replace efx_nic_type::phys_addr_channels with efx_nic::max_channels, to be initialised by the probe function. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
MCDI v2 adds a second header dword with wider command and length fields. It also defines extra error codes. Change the fallback error number for unknown MCDI error codes from EIO to EPROTO. EIO is treated as indicating the MCDI transport has failed and we need to reset the function, which is rather drastic. v2 error codes and lengths don't fit into completion events, so for a v2-capable transport, always read the response header rather then using the event fields. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Add efx_nic_type operations for the many efx_nic functions that need to be implemented different on EF10. For now, change most of the existing efx_nic_*() functions into inline wrappers. As a later step, we may be able to improve branch prediction for operations used on the fast path by copying the pointers into each queue/channel structure. Move the Falcon/Siena implementations to new file farch.c and rename the functions and static data to use a prefix of 'efx_farch_'. Move efx_may_push_tx_desc() to nic.h, as the EF10 TX code will also use it. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Currently efx_stop_datapath() will try to flush our DMA queues (if DMA is enabled), then finalise software and hardware state for each queue. However, for EF10 we must ask the MC to finalise each queue, which implicitly starts flushing it, and then wait for the flush events. We therefore need to delegate more of this to the NIC type. Combine all the hardware operations into a new NIC-type operation efx_nic_type::fini_dmaq, and call this before tearing down the software state and buffers for all the DMA queues. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
The EF10 architecture has a very different register layout from previous controllers, so we'll use separate files for the two sets of register definitions. Use 'farch' as an abbreviation for Falcon-architecture. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Most call sites for efx_nic_alloc_buffer() are part of the probe or reconfiguration paths and can allocate with GFP_KERNEL. A few others should use GFP_NOIO (I think). Only one is in atomic context and must use the current GFP_ATOMIC. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Move the lowest layer (transport) of the current MCDI code to per-NIC-type operations. Introduce a new structure and efx_nic member for MCDI-specific data. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
This should probably be done during MCDI initialisation for any NIC. Change efx_mcdi_init() to return an error code. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Collect together MCDI port functions from mcdi.c, mcdi_mac.c, mcdi_phy.c and siena.c. Rename the 'siena' functions accordingly. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
EF10 does not include a multicast hash filter, so this function is specific to Siena. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
These implementations should work for EF10 too. Rename them accordingly. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 12 6月, 2013 1 次提交
-
-
由 Ben Hutchings 提交于
We should not use net_device::dev_id to indicate the port number, as this affects the way the local part of IPv6 addresses is normally generated. This field was intended for use where multiple devices may share a single assigned MAC address and need to have different IPv6 addresses. Siena's two ports each have their own MAC addresses. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 3月, 2013 2 次提交
-
-
由 Ben Hutchings 提交于
Enable RX DMA scattering iff an RX buffer large enough for the current MTU will not fit into a single page and the NIC supports DMA scattering for kernel-mode RX queues. On Falcon and Siena, the RX_USR_BUF_SIZE field is used as the DMA limit for both all RX queues with scatter enabled. Set it to 1824, matching what Onload uses now. Maintain a statistic for frames truncated due to lack of descriptors (rx_nodesc_trunc). This is distinct from rx_frm_trunc which may be incremented when scattering is disabled and implies an over-length frame. Whenever an MTU change causes scattering to be turned on or off, update filters that point to the PF queues, but leave others unchanged, as VF drivers assume scattering is off. Add n_frags parameters to various functions, and make them iterate: - efx_rx_packet() - efx_recycle_rx_buffers() - efx_rx_mk_skb() - efx_rx_deliver() Make efx_handle_rx_event() responsible for updating efx_rx_queue::removed_count. Change the RX pipeline state to a starting ring index and number of fragments, and make __efx_rx_packet() responsible for clearing it. Based on earlier versions by David Riddoch and Jon Cooper. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Alexandre Rames 提交于
The Linux side of EEH is triggered by MMIO reads, but this driver's data path does not issue any MMIO reads (except in legacy interrupt mode). Therefore add a monitor function to poll EEH periodically. When preparing to reset the device based on our own error detection, also poll EEH and defer to its recovery mechanism if appropriate. [bwh: Use a separate condition for the initial link poll; fix some style errors] Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 01 12月, 2012 2 次提交
-
-
由 Ben Hutchings 提交于
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Receiving pause frames can block TX queue flushes. Earlier changes work around this by reconfiguring the MAC during flushes for VFs, but during flushes for the PF we would only change the fc_disable counter. Unless the MAC is reconfigured for some other reason during the flush (which I would not expect to happen) this had no effect at all. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 19 9月, 2012 1 次提交
-
-
由 Stuart Hodgson 提交于
Add PTP IEEE-1588 support and make accesible via the PHC subsystem. This work is based on prior code by Andrew Jackson Signed-off-by: NStuart Hodgson <smhodgson@solarflare.com> [bwh: - Add byte order conversion in efx_ptp_send_times() - Simplify conversion of PPS event times - Add the built-in vs module check to CONFIG_SFC_PTP dependencies] Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 17 7月, 2012 2 次提交
-
-
由 Ben Hutchings 提交于
Some interface statistics are computed in such a way that they can sometimes decrease (and even underflow). Since the computed value will never be greater than the true value, we fix this by only storing the computed value when it increases. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Currently VF queues and drivers may remain active during this test. This could cause memory corruption or spurious test failures. Therefore we reset the port/function before running these tests on Siena. On Falcon this doesn't work: we have to do some additional initialisation before some blocks will work again. So refactor the reset/register-test sequence into an efx_nic_type method so efx_selftest() doesn't have to consider such quirks. In the process, fix another minor bug: Siena does not have an 'invisible' reset and the self-test currently fails to push the PHY configuration after resetting. Passing RESET_TYPE_ALL to efx_reset_{down,up}() fixes this. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 07 3月, 2012 1 次提交
-
-
由 Ben Hutchings 提交于
This function is now used in only one place, where it always returns true. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 16 2月, 2012 2 次提交
-
-
由 Ben Hutchings 提交于
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs), each with an RX queue, a TX queue, an event queue and a mailbox register. These may be assigned to up to 127 SR-IOV virtual functions per port, with up to 64 VIs per VF. We allocate an extra channel (IRQ and event queue only) to receive requests from VF drivers. There is a per-port limit of 4 concurrent RX queue flushes, and queue flushes may be initiated by the MC in response to a Function Level Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all flush requests via the MC. The RSS indirection table is shared with VFs, so the number of RX queues used in the PF is limited to the number of VIs per VF. This is almost entirely the work of Steve Hodgson, formerly shodgson@solarflare.com. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
Each port has a block of 64-bit SRAM that is divided between buffer table and descriptor cache regions at initialisation time. Currently we use a fixed allocation, but it needs to be changed to support larger numbers of queues. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
- 27 1月, 2012 3 次提交
-
-
由 Ben Hutchings 提交于
The SFC9000-family controllers have firmware to manage all board peripherals including temperature, heat sink continuity and voltage sensors. The firmware reports sensor alarms, which we log, and will shut down the board if necessary. Some users may want to monitor their boards more closely, so add an hwmon driver that exposes all sensors reported by the firmware. Move efx_mcdi_sensor_event() into the new file so it can share the array of sensor labels with the hwmon driver. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Ben Hutchings 提交于
We currently assume that the timer quantum for Siena is 5 us, the same as for Falcon. This is not correct; timer ticks are generated on a rota which takes a minimum of 768 cycles (each event delivery or other timer change will delay it by 3 cycles). The timer quantum should be 6.144 or 3.072 us depending on whether turbo mode is active. Replace EFX_IRQ_MOD_RESOLUTION with a timer_quantum_ns field in struct efx_nic, initialised by the efx_nic_type::probe function. While we're at it, replace EFX_IRQ_MOD_MAX with a timer_period_max field in struct efx_nic_type. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-
由 Matthew Slattery 提交于
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
-