- 27 2月, 2010 2 次提交
-
-
由 Manuel Lauss 提交于
remove board_init_irq(): On all in-kernel boards it is sufficient to initialize board interrupts in an arch_initcall by using the default linux irq functions. Some small irqmap.c files have been folded into board_setup files. Run-tested on DB1200; compile-tested on all other affected boards. Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Manuel Lauss 提交于
All Alchemy development boards have external CPLDs with a few registers in them. They all share an identical register layout with only a few minor differences (except the PB1000) in bit functions and base addresses. This patch - adds a primitive facility to initialize and use these external registers, - replaces all occurrences of bcsr->xxx accesses with calls to the new functions (the pb1200 cascade irq handling code is special). - collects BCSR register information scattered throughout the board headers in a central place. Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 17 6月, 2009 1 次提交
-
-
由 Manuel Lauss 提交于
Replace a few open-coded GPIO register accesses with gpio calls. Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 11 1月, 2009 4 次提交
-
-
由 Manuel Lauss 提交于
This patch attempts to modernize core Alchemy interrupt handling code. - add irq_chips for irq controllers instead of irq type, - add a set_type() hook to change irq trigger type during runtime, - add a set_wake() hook to control GPIO0..7 based wakeup, - use linux' IRQF_TRIGGER_ constants instead of homebrew ones, - enable GENERIC_HARDIRQS_NO__DO_IRQ. - simplify plat_irq_dispatch - merge au1xxx_irqmap into irq.c file, the only place where its contents are referenced. - board_init_irq() is now mandatory for every board; use it to register the remaining (gpio-based) interrupt sources; update all boards accordingly. Run-tested on Db1200 and other Au1200 based platforms. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
-
由 Manuel Lauss 提交于
Not every alchemy-based board might want these options forced on it, and most of this stuff seems to be intended for devboard code anyway. Remove commandline mangling code out of common chip code and instead add relevant sections to all in-tree boards to not change existing behaviour. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Manuel Lauss 提交于
Share some code and merge small files: - Extract the prom init code from all devboard files (they only differ in memory configuration). - Merge the irq configuration into board setup code. - Merge smaller files into board setup code. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org> delete mode 100644 arch/mips/alchemy/devboards/db1x00/init.c delete mode 100644 arch/mips/alchemy/devboards/pb1000/init.c delete mode 100644 arch/mips/alchemy/devboards/pb1000/irqmap.c delete mode 100644 arch/mips/alchemy/devboards/pb1100/init.c delete mode 100644 arch/mips/alchemy/devboards/pb1100/irqmap.c delete mode 100644 arch/mips/alchemy/devboards/pb1200/init.c delete mode 100644 arch/mips/alchemy/devboards/pb1500/init.c delete mode 100644 arch/mips/alchemy/devboards/pb1500/irqmap.c delete mode 100644 arch/mips/alchemy/devboards/pb1550/init.c delete mode 100644 arch/mips/alchemy/devboards/pb1550/irqmap.c create mode 100644 arch/mips/alchemy/devboards/prom.c
-
由 Manuel Lauss 提交于
This should ease sharing of common devboard code. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 11 10月, 2008 1 次提交
-
-
由 Ralf Baechle 提交于
It's more than the au1000 these days. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 12 5月, 2008 1 次提交
-
-
由 Sergei Shtylyov 提交于
Fix several errors and warnings given by checkpatch.pl: - use of C99 // comments; - printk() without KERN_* facility level; - unnecessary braces for single-statement block; - using simple_strtol() where strict_strtol() could be used. In addition to these changes, also do the following: - replace numeric literals/expressions with the matching macros; - insert spaces between operator and its operands; - properly indent the code and the array initializers; - remove useless #if dirctive from board_setup(); - remove needless parentheses; - remove unneeded type casts; - remove excess new lines; - make hexadecimal literals all lower case; - remove space after the type cast's closing parenthesis; - insert missing space before closing brace in the array initializers; - replace spaces after the macro name with tabs in the #define directives, also sometimes insert space there for better looks; - fix typos/errors, capitalize acronyms, etc. in the comments; - update MontaVista copyright; - remove Pete Popov's old email address... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 29 4月, 2008 1 次提交
-
-
由 Sergei Shtylyov 提交于
Go thru the Alchemy code and hunt down every unneeded #include, #define, and extern (some of which refer to already long dead functions). Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 12 10月, 2007 1 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 09 10月, 2007 1 次提交
-
-
由 Florian Fainelli 提交于
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO pin not being pulled high, and thus the USB switch not being powered at all. This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which started in 2005 (before 2.6.12-rc2), then probably because things were working anyway for most people got forgotten. [Ralf: Paolo's original patch didn't fix the module case, Florian's patch only fixed MTX1 etc. so this is a combined patch plus some cleanups.] Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn Crispin <blogic@openwrt.org> Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 27 6月, 2007 1 次提交
-
-
由 Yoichi Yuasa 提交于
au_readl() is correct here. Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 10 10月, 2006 1 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-