In function dsi_compute_interleave_lp(), the escape clock/LP clock time period
is calculated incorrectly. The escape clock/LP clock is calculated as:

LP Clock(Hz) = DSI_FCLK(Hz) / lp_clk_div

Since we are calculating the time period of LP clock, the LP clock divider
should be multiplied with the time period of DSI_FCLK.

Calculating incorrect value of txclkesc results in incorrect calculation of LP
interleaving parameters, it also creates a possibility of a divide by zero
error.
Reported-by: NSureshkumar Manimuthu <mail2msuresh@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.

This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSI supports interleaving of command mode packets during the HSA, HFP, HBP and
BLLP blanking intervals in a video mode stream. This is useful as a user may
want to read or change the configuration of a panel without stopping the video
stream.

On OMAP DSI, we can queue HS or LP command mode packets in the TX FIFO, and
the DSI HW takes care of interleaving this data during the one of the blanking
intervals. The DSI HW needs to be programmed with the maximum amount of data
that can be interleaved in a particular blanking period. A blanking period
cannot be used to send command mode data for it's complete duration, there is
some amount of time required for the DSI data and clock lanes to transition
to the desired LP or HS state.

Based on the state of the lanes at the beginning and end of the blanking period,
we have different scenarios, with each scenario having a different value of time
required to transition to HS or LP. Refer to the section 'Interleaving Mode' in
OMAP TRM for more info on the scenarios and the equations to calculate the time
required for HS or LP transitions.

We use the scenarios which takes the maximum time for HS or LP transition, this
gives us the minimum amount of time that can be used to interleave command mode
data. The amount of data that can be sent during this minimum time is calculated
for command mode packets both in LP and HS. These are written to the registers
DSI_VM_TIMING4 to DSI_VM_TIMING6.

The calculations don't take into account the time required of transmitting BTA
when doing a DSI read, or verifying if a DSI write went through correctly. Until
these latencies aren't considered, the behaviour of DSI is unpredictable when
a BTA is interleaved during a blanking period. Enhancement of these calculations
is a TODO item.

The calculations are derived from DSI parameter calculation tools written by
Sebastien Fagard <s-fagard@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move the platform-data based display device initialization into a
separate function, so that we may later add of-based initialization.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We currently use the id of the dsi platform device (dsidev->id) as the
DSI hardware module ID. This works because we assign the ID manually in
arch/arm/mach-omap2/display.c at boot time.

However, with device tree the platform device IDs are automatically
assigned to an arbitrary number, and we can't use it.

Instead of using dsidev->id during operation, this patch stores the
value of dsidev->id to a private field of the dsi driver at probe(). The
future device tree code can thus set the private field with some other
way.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that each output driver creates their own display devices, the
output drivers can also initialize those devices.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently the higher level omapdss platform driver gets the list of
displays in its platform data, and uses that list to create the
omap_dss_device for each display.

With DT, the logical way to do the above is to list the displays under
each individual output, i.e. we'd have "dpi" node, under which we would
have the display that uses DPI. In other words, each output driver
handles the displays that use that particular output.

To make the current code ready for DT, this patch modifies the output
drivers so that each of them creates the display devices which use that
output. However, instead of changing the platform data to suit this
method, each output driver is passed the full list of displays, and the
drivers pick the displays that are meant for them. This allows us to
keep the old platform data, and thus we avoid the need to change the
board files.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that we are using platform_driver_probe() we can add __inits and
__exits all around.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that the core.c doesn't fail if output driver's init fails, we can
change the uses of platform_driver_register to platform_driver_probe.
This will allow us to use __init in the following patches.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of having an ugly #ifdef mess in the core.c for creating debugfs
files, add a dss_debugfs_create_file() function that the dss drivers
can use to create the debugfs files.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that the omapdss_core device is the parent for all other dss
devices, we don't need to use the dss_runtime_get/put anymore. Instead,
enabling omapdss_core will happen automatically when a child device is
enabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

For unknown reasons we seem to have a return in each of the omapdss's
uninit functions, which is a void function.

Remove the returns.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:

- Remove struct omap_display_platform_data. It was used just as a
  wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
  dss hwmods do not need the platform data. This should also work better
  for DT, as we can create omapdss device programmatically in generic omap
  boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
  that the dss hwmod drivers can call.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DSI driver uses dsi_get_dsidev_id() to get the ID number for the DSI
instance. However, there were a few places where dsidev->id was used
instead of the function. Fix those places to use the function.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Replace the function dispc_mgr_set_timings() with dss_mgr_set_timings() in the
interface drivers. The latter function ensures that the timing related DISPC
registers are configured according to the shadow register programming model.

Remove the call to dispc_mgr_go() in dpi_set_timings() as the manager's go bit
is set by dss_mgr_set_timings().
Signed-off-by: NArchit Taneja <archit@ti.com>

Fake VSYNC support is a hack and has some bugs in it. It isn't used by any user
of DSS. Remove Fake VSYNC support. For DSI command mode and RFBI panels, a user
of DSS should wait for the completion of a frame by using the panel driver's
sync op.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.

This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.

The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:

{
	0,	// pin num for clock lane +
	1,	// pin num for clock lane -
	2,	// pin num for data1 lane +
	3,	// pin num for data1 lane -
	...
}

The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Currently, a LCD manager's timings is set by dispc_mgr_set_lcd_timings() and TV
manager's timings is set by dispc_set_digit_size(). Use a common function called
dispc_mgr_set_timings() which sets timings for both type of managers.

We finally want the interface drivers to use an overlay manager function to
configure it's timings, having a common DISPC function would make things
cleaner.

For LCD managers, dispc_mgr_set_timings() sets LCD size and blanking values, for
TV manager, it sets only the TV size since blanking values don't exist for TV.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

For some OMAP versions the TRM says that the pixel clock from DISPC can
be used as an input clock for DSI PLL, instead of the default, which is
sysclk.  For some OMAP versions the bits affecting this are marked as
reserved.  This feature has never been tested, so it's unknown if the HW
even works, and has never been used.

To clean things up, this patch removes the functionality. This should
not affect any board.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.

This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.

Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.

This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>

The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move fifo threshold calculation into dispc.c, as the thresholds are
really dispc internal thing.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

The clock names of DSI_PLL_HSDIV_DISPC and DSI_PLL_HSDIV_DSI was made
dynamic based on the current value of DISPC and DSI FCLK sources. This
doesn't need to be done since we are just interested in the clock names,
and not the current clock sources for DISPC and DSI FCLKs.

Use only the generic and omap specific names for the DSI PLL's HSDIV
clocks.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that dss_mgr_enable returns an error value, check it in all the
places dss_mgr_enable is used, and bail out properly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.

However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.

This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omap_overlay_manager struct contains enable() and disable() functions.
However, these are only meant to be used from inside omapdss, and thus
it's bad to expose the functions.

This patch adds dss_mgr_enable() and dss_mgr_disable() functions to
apply.c, which handle enabling and disabling the output.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dss_start_update() takes currently the dss device as a parameter. Change
the parameter to ovl manager, as that is what the dss_start_update()
actually needs. Change the name of the function to
dss_mgr_start_update() to reflect the change.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
  be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex

Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.

This patch removes the partial update from the dsi.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
  be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex

Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.

This patch removes the partial update from the manager.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

ULPS cannot be entered if the DDR clk is enabled. Thus disable the DDR
clk before entering ULPS.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We sometimes get timeout when disabling the DSI interface with video
mode. It looks like the disable will stall until the current frame has
been finished, and this can take multiple milliseconds.

wait_for_bit_change() currently uses a busyloop to wait for a bit to
change. This is used in multiple places. The problem is, we don't have
clear understanding how long particular operations can take, so the
function needs to support longer waits.

Improve wait_for_bit_change() to first busy loop for 100 times to see if
the bit changes almost right away. If the bit hasn't changed, move to a
loop with a sleep of 1ms, and poll for 500ms.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current code always enters ULPS for 3 lanes. This is not right, as
there could be only 2 lanes used, and on OMAP4 we have 5 lanes.

Fix the code to put all used lanes into ULPS.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

There's no longer need for the dsi_get_num_lanes_used function, so it
can be removed. The lane check in dsi_init_display() can be removed as
the validity of the config will be verified when parsing it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_cio_enable_lane_override(). The function
parameters are also slightly changed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_cio_wait_tx_clk_esc_reset(). This also
extends the function to support 5 lanes on OMAP4, instead of 3 lanes.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_get_lane_mask().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_set_lane_config().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Parse the lane configuration from the device data into internal lane
config format. This will be used in the following patches to clean up
the lane handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>