* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (34 commits)
  USB: xhci: Stall handling bug fixes.
  USB: xhci: Support for 64-byte contexts
  USB: xhci: Always align output device contexts to 64 bytes.
  USB: xhci: Scratchpad buffer allocation
  USB: Fix parsing of SuperSpeed Endpoint Companion descriptor.
  USB: xhci: Fail gracefully if there's no SS ep companion descriptor.
  USB: xhci: Handle babble errors on transfers.
  USB: xhci: Setup HW retries correctly.
  USB: xhci: Check if the host controller died in IRQ handler.
  USB: xhci: Don't oops if the host doesn't halt.
  USB: xhci: Make debugging more verbose.
  USB: xhci: Correct Event Handler Busy flag usage.
  USB: xhci: Handle short control packets correctly.
  USB: xhci: Represent 64-bit addresses with one u64.
  USB: xhci: Use GFP_ATOMIC while holding spinlocks.
  USB: xhci: Deal with stalled endpoints.
  USB: xhci: Set TD size in transfer TRB.
  USB: xhci: fix less- and greater than confusion
  USB: usbtest: no need for USB_DEVICEFS
  USB: musb: fix CONFIGDATA register read issue
  ...

We really don't want to mark the pty as a low-latency device, because as
Alan points out, the ->write method can be called from an IRQ (ppp?),
and that means we can't use ->low_latency=1 as we take mutexes in the
low_latency case.

So rather than using low_latency to force the written data to be pushed
to the ldisc handling at 'write()' time, just make the reader side (or
the poll function) do the flush when it checks whether there is data to
be had.

This also fixes the problem with lost data in an emacs compile buffer
(bugzilla 13815), and we can thus revert the low_latency pty hack
(commit 3a542974: "pty: quickfix for the
pty ENXIO timing problems").
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[ Modified to do the tty_flush_to_ldisc() inside input_available_p() so
  that it triggers for both read and poll()  - Linus]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Correct the xHCI code to handle stalls on USB endpoints.  We need to move
the endpoint ring's dequeue pointer past the stalled transfer, or the HW
will try to restart the transfer the next time the doorbell is rung.

Don't attempt to clear a halt on an endpoint if we haven't seen a stalled
transfer for it.  The USB core will attempt to clear a halt on all
endpoints when it selects a new configuration.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (asus_atk0110) Fix upper limit readings
  hwmon: (smsc47m1) Differentiate between LPC47M233 and LPC47M292

Adds support for controllers that use 64-byte contexts.  The following context
data structures are affected by this: Device, Input, Input Control, Endpoint,
and Slot.  To accommodate the use of either 32 or 64-byte contexts, a Device or
Input context can only be accessed through functions which look-up and return
pointers to their contained contexts.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure the xHCI output device context is 64-byte aligned.  Previous
code was using the same structure for both the output device context and
the input control context.  Since the structure had 32 bytes of flags
before the device context, the output device context wouldn't be 64-byte
aligned.  Define a new structure to use for the output device context and
clean up the debugging for these two structures.

The copy of the device context in the input control context does *not*
need to be 64-byte aligned.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allocates and initializes the scratchpad buffer array (XHCI 4.20).  This is an
array of 64-bit DMA addresses to scratch pages that the controller may use
during operation.  The number of pages is specified in the "Max Scratchpad
Buffers" field of HCSPARAMS2.  The DMA address of this array is written into
slot 0 of the DCBAA.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_parse_ss_endpoint_companion() was supposed to allocate a structure to
hold the SuperSpeed Endpoint Companion descriptor, and either copy the
values the device returned, or fill in default values if the device
descriptor did not include the companion descriptor.

However, the previous code would miss the last endpoint in a configuration
with no descriptors after it.  Make usb_parse_endpoint() allocate the SS
endpoint companion descriptor and fill it with default values, even if
we've run out of buffer space in this configuration descriptor.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor
parsing code.  It fails in some corner cases, which means ep->ss_ep_comp may be
NULL.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Pass back a babble error when this error code is seen in the transfer event TRB.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xHCI host controller can be programmed to retry a transfer a certain number
of times per endpoint before it passes back an error condition to the host
controller driver.  The xHC will return an error code when the error count
transitions from 1 to 0.  Programming an error count of 3 means the xHC tries
the transfer 3 times, programming it with a 1 means it tries to transfer once,
and programming it with 0 means the HW tries the transfer infinitely.

We want isochronous transfers to only be tried once, so set the error count to
one.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add more debugging to the irq handler, slot context initialization, ring
operations, URB cancellation, and MMIO writes.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Event Handler Busy bit in the event ring dequeue pointer is write 1 to
clear.  Fix the interrupt service routine to clear that bit after the
event handler has run.

xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer
without changing any of the four reserved bits in the lower nibble.  The event
handler busy (EHB) bit is write one to clear, so the new value must always
contain a zero in that bit in order to preserve the EHB value.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When there is a short packet on a control transfer, the xHCI host controller
hardware will generate two events.  The first event will be for the data stage
TD with a completion code for a short packet.  The second event will be for the
status stage with a successful completion code.  Before this patch, the xHCI
driver would giveback the short control URB when it received the event for the
data stage TD.  Then it would become confused when it saw a status stage event
for the endpoint for an URB it had already finished processing.

Change the xHCI host controller driver to wait for the status stage event when
it receives a short transfer completion code for a data stage TD.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are several xHCI data structures that use two 32-bit fields to
represent a 64-bit address.  Since some architectures don't support 64-bit
PCI writes, the fields need to be written in two 32-bit writes.  The xHCI
specification says that if a platform is incapable of generating 64-bit
writes, software must write the low 32-bits first, then the high 32-bits.
Hardware that supports 64-bit addressing will wait for the high 32-bit
write before reading the revised value, and hardware that only supports
32-bit writes will ignore the high 32-bit write.

Previous xHCI code represented 64-bit addresses with two u32 values.  This
lead to buggy code that would write the 32-bits in the wrong order, or
forget to write the upper 32-bits.  Change the two u32s to one u64 and
create a function call to write all 64-bit addresses in the proper order.
This new function could be modified in the future if all platforms support
64-bit writes.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xHCI functions to queue an URB onto the hardware rings must be called
with the xhci spinlock held.  Those functions will allocate memory, and
take a gfp_t memory flags argument.  We must pass them the GFP_ATOMIC
flag, since we don't want the memory allocation to attempt to sleep while
waiting for more memory to become available.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When an endpoint on a device under an xHCI host controller stalls, the
host controller driver must let the hardware know that the USB core has
successfully cleared the halt condition.  The HCD submits a Reset Endpoint
Command, which will clear the toggle bit for USB 2.0 devices, and set the
sequence number to zero for USB 3.0 devices.

The xHCI urb_enqueue will accept new URBs while the endpoint is halted,
and will queue them to the hardware rings.  However, the endpoint doorbell
will not be rung until the Reset Endpoint Command completes.

Don't queue a reset endpoint command for root hubs.  khubd clears halt
conditions on the roothub during the initialization process, but the roothub
isn't a real device, so the xHCI host controller doesn't need to know about the
cleared halt.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The 0.95 xHCI specification requires software to set the "TD size" field
in each transaction request block (TRB).  This field gives the host
controller an indication of how much data is remaining in the TD
(including the buffer in the current TRB).  Set this field in bulk TRBs
and data stage TRBs for control transfers.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Without this change the loops won't start
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

THis patch (as1270) allows the usbtest module to be built even when
USB_DEVICEFS isn't configured.  Tests can be performed without
USB_DEVICEFS, using the /dev/bus/usb/*/* device files.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

INDEX register has to be set to '0' before reading
CONFIGDATA register which is only present in TI musb
platforms.

Currently the default register access mode is set to
FLAT_MODE thus INDEX register is not getting set
properly with musb_ep_select() which is just a nop
operation in FLAT_MODE.This invalid register read is
causing module reinset failure.

Fixing the issue by moving INDEX register write part to
musb_read_configdata() function itself.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG.
Make sure any reference to it is also under the same #ifdef.

Without this fix, the driver failes to compile when USB_OTG is defined
but USB_MUSB_OTG isn't.
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This function uses wrong bit mask to prevent clearing RXCSR status
bits when halting an endpoint -- which results in clearing SentStall
and RxPktRdy bits (that the code actually tries to avoid); must be
a result of cut-and-paste...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added support for the Alcatel X060S/X200 broadband modems to the option
driver. The device starts in cd-rom emulation mode (1bbb:f000) and
requires the use of the usb_modeswitch tool to switch it to modem mode
(1bbb:0000).
Signed-off-by: NJavier Martin <jmartinj@iname.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPeng Huang <shawn.p.huang@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've opened up the case, and the chips in the ATEN UC2324 are:

Moschip
MCS7840CV-AA
69507-6B1
0650
(USB to 4-port serial)

(logo with AF kerned together)  0748  
24BC02  
SINGLP
(unknown 8-pin chip)

(logo looks like 3 or Z in circle)
ZT3243LEEA    0752
B7A16420.T
(4 chips, so this will be RS232 line driver)
(Probably equivalent of Sipex SP3243)

So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840,
and should use the mos7840.c driver.  I expect you will remove the
aten2011.c driver from the staging area.

From the aten2011.c source code, the device ID for the UC2322 (2 port
serial) is 0x7820, just like the Moschip evaluation board.  This value
should be added to the device id table of mos7840.c.

Here's a patch that adds these devices to the driver.


From: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

BugLink: https://bugs.launchpad.net/bugs/365291Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.

These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Ming Zhao <zhao.ming9@zte.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed that USB initialization didn't setup correctly on my kirkwood
based board (OpenRD base) if I hadn't initialized USB in U-boot first.
The error message looks like this:

  ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  orion-ehci orion-ehci.0: Marvell Orion EHCI
  orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
  orion-ehci orion-ehci.0: can't setup
  orion-ehci orion-ehci.0: USB bus 1 deregistered
  orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110
  orion-ehci: probe of orion-ehci.0 failed with error -110

which is caused by ehci_halt() timing out in the handshake() call. I
noticed that U-boot does a reset before calling handshake(), so this
patch does the same thing for Linux. USB now works for me.
Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: NVille Sundberg <vsundber@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OMAP: OHCI: hc_driver's stop method should call ohci_stop

Without this, the ohci-omap driver will not cleanup the debugfs
nodes when the driver is unloaded. So the next insmod will fail,
if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected.
Reported-by: Nvikram pandita <vikram.pandita@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Requests to get max LUN, for certain USB storage devices, require a
longer timeout before a correct reply is returned. This happens for a
Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set
to 0, thus losing functionality, because of the timeout occurring too
quickly.

Raising the timeout value fixes the issue and might help other devices
to return a correct max LUN value as well.
Signed-off-by: NGiacomo Lozito <james@develia.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is needed for compilation without CONFIG_PM.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After commit f092c240 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:

drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'

So I removed it.
Signed-off-by: NCarlos R. Mafra <crmafra@aei.mpg.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c/tsl2550: Fix lux value in dark environment

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (22 commits)
  Btrfs: Fix async caching interaction with unmount
  Btrfs: change how we unpin extents
  Btrfs: Correct redundant test in add_inode_ref
  Btrfs: find smallest available device extent during chunk allocation
  Btrfs: clear all space_info->full after removing a block group
  Btrfs: make flushoncommit mount option correctly wait on ordered_extents
  Btrfs: Avoid delayed reference update looping
  Btrfs: Fix ordering of key field checks in btrfs_previous_item
  Btrfs: find_free_dev_extent doesn't handle holes at the start of the device
  Btrfs: Remove code duplication in comp_keys
  Btrfs: async block group caching
  Btrfs: use hybrid extents+bitmap rb tree for free space
  Btrfs: Fix crash on read failures at mount
  Btrfs: remove of redundant btrfs_header_level
  Btrfs: adjust NULL test
  Btrfs: Remove broken sanity check from btrfs_rmap_block()
  Btrfs: convert nested spin_lock_irqsave to spin_lock
  Btrfs: make sure all dirty blocks are written at commit time
  Btrfs: fix locking issue in btrfs_find_next_key
  Btrfs: fix double increment of path->slots[0] in btrfs_next_leaf
  ...

The size of receive buffer pointer was used to get size of
receive buffer instead of recvbuf_size itself, so only 4/8
bytes could be transfered.

This is a regression to 2.6.30 introduced by commit
8c90e11e ("mISDN: Use
kernel_{send,recv}msg instead of open coding")
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>