Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

With sync-after dependencies, given "lucky" timing of pause/unpause
events, and the end of an empty (0 bits set) resync was sometimes not
detected on the SyncTarget, leading to a "stalled" SyncSource state.

Fixed this by expecting not only "Inconsistent -> UpToDate" but also
"Consistent -> UpToDate" transitions for the peer disk state
to end a resync.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If we get into the C_BROKEN_PIPE cstate once, the state engine set the
thi->t_state of the receiver thread to restarting.  But with the while loop
in drbdd_init() a new connection gets established. After the call into
drbdd() returns immediately since the thi->t_state is not RUNNING.  The
restart of drbd_init() then resets thi->t_state to RUNNING.

I.e. after entering C_BROKEN_PIPE once, the next successful established
connection gets wasted.

The two parts of the fix:
  * Do not cause the thread to restart if we detect the issue
    with the sockets while we are in C_WF_CONNECTION.

  * Make sure that all actions that would have set us to C_BROKEN_PIPE
    happen before the state change to C_WF_REPORT_PARAMS.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Cherry picked form 8.4
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

...when the peer has inconsistent data. In that case we failed to
clear the susp_nod flag. When the local disk was attached again
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Now, the new edition of the clause only fires if a diskless
peer gets promoted.

This is a fixup for "drbd: Delayed creation of current-UUID".
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Bitmap IO may happend in the context of an application write,
in the generic block IO path.  We need to use GFP_NOIO.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

When the disk-timeout is active, and it expires for a single request,
we consider the local disk as D_FAILED. Note: With this change,
I made both timeout based state transitions HARD state transitions.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The last bunch of commits prepared the 'detach from tar pit' feature.
With that we can be for long time in disk state FAILED. We need
to accept new IO requests during that time.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The new function drbd_md_get_buffer() aborts waiting for the buffer
in case the disk failes in the meantime.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Regression introduced with 8.3.11 commit:
drbd: Take a more conservative approach when deciding max_bio_size

Never ever tell an older drbd, that we support more than 32KiB
in a single data request (packet).
Never believe an older drbd, that is supports more than 32KiB
in a single data request (packet)
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The reason for this change is that, with when doing
'drbdadm invalidate' on a disconnected resource caused
an "implicitly set pdsk from UpToDate to DUnknown" message,
which was missleading.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Fix warnings of the following nature in the drbd header:

In file included from drivers/block/drbd/drbd_bitmap.c:32:
drivers/block/drbd/drbd_int.h: In function 'drbd_get_syncer_progress':
drivers/block/drbd/drbd_int.h:2234: warning: comparison is always false due to limited range of data

where mdev->rs_total (an unsigned long) is being compared to 1ULL << 32, which
is always false on a 32-bit machine.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>

It is not "to small", but "too small".
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

For large resync rates, seq_printf_with_thousands_grouping()
accidentally only produced Y,000,00Y, instead of the real numbers.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Clearing bit 5 of CACHE_MODE_0 is necessary to prevent GPU hangs in
OpenGL programs such as Google MapsGL, Google Earth, and gzdoom when
using separate stencil buffers.  Without it, the GPU tries to use the
LRA eviction policy, which isn't supported.  This was supposed to be off
by default, but seems to be on for many machines.

This cannot be done in gen6_init_clock_gating with most of the other
workaround bits; the render ring needs to exist.  Otherwise, the
register write gets dropped on the floor (one printk will show it
changed, but a second printk immediately following shows the value
reverts to the old one).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47535
Cc: stable@vger.kernel.org
Cc: Rob Castle <futuredub@gmail.com>
Cc: Eric Appleman <erappleman@gmail.com>
Cc: aaron667@gmx.net
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Makes Nutmeg DP to VGA bridges work for me.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=42490

Noticed by Jerome Glisse (after weeks of debugging).
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch ensures that the last bit of a transfer gets correctly
flushed out of the register.
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This condition is used to determine 8 bits or 16 and 32 bits transfer.
Obviously it is reversed.
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Since the member was dropped from the common Blackfin header, we need
to stop using it in the SPORT driver too.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

No other SPI controller has this field, and SPI clients should be setting
this up in their own drivers.  So drop it from the Blackfin controller to
keep people from using it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Each transfer may have its own bits per word.
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This controller is only for blackfin 5xx soc, so rename it to BFIN5XX
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Currently, if we request for frequency greater than maximum possible, spi driver
returns error.

For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...

It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...

For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: NVinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.

To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
  size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
  bad idea leading to quick interrupt handler re-entrancy
Tested-by: NTanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

A new enum indicating the dma channel direction was introduced by:

commit 49920bc6
    dmaengine: add new enum dma_transfer_direction

The following commit changed spi-ep93xx to use the new enum:

commit a485df4b
    spi, serial: move to dma_transfer_direction

In doing so a sparse warning was introduced:

warning: mixing different enum types
   int enum dma_data_direction  versus
   int enum dma_transfer_direction

This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.

Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>