提交 d4b9b578 编写于 作者: H H Hartley Sweeten 提交者: Grant Likely

spi/spi-ep93xx.c: use dma_transfer_direction instead of dma_data_direction

A new enum indicating the dma channel direction was introduced by:

commit 49920bc6
    dmaengine: add new enum dma_transfer_direction

The following commit changed spi-ep93xx to use the new enum:

commit a485df4b
    spi, serial: move to dma_transfer_direction

In doing so a sparse warning was introduced:

warning: mixing different enum types
   int enum dma_data_direction  versus
   int enum dma_transfer_direction

This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.

Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
上级 dbabe0d6
......@@ -545,13 +545,12 @@ static void ep93xx_spi_pio_transfer(struct ep93xx_spi *espi)
* in case of failure.
*/
static struct dma_async_tx_descriptor *
ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_transfer_direction dir)
{
struct spi_transfer *t = espi->current_msg->state;
struct dma_async_tx_descriptor *txd;
enum dma_slave_buswidth buswidth;
struct dma_slave_config conf;
enum dma_transfer_direction slave_dirn;
struct scatterlist *sg;
struct sg_table *sgt;
struct dma_chan *chan;
......@@ -567,14 +566,13 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
memset(&conf, 0, sizeof(conf));
conf.direction = dir;
if (dir == DMA_FROM_DEVICE) {
if (dir == DMA_DEV_TO_MEM) {
chan = espi->dma_rx;
buf = t->rx_buf;
sgt = &espi->rx_sgt;
conf.src_addr = espi->sspdr_phys;
conf.src_addr_width = buswidth;
slave_dirn = DMA_DEV_TO_MEM;
} else {
chan = espi->dma_tx;
buf = t->tx_buf;
......@@ -582,7 +580,6 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
conf.dst_addr = espi->sspdr_phys;
conf.dst_addr_width = buswidth;
slave_dirn = DMA_MEM_TO_DEV;
}
ret = dmaengine_slave_config(chan, &conf);
......@@ -633,8 +630,7 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
if (!nents)
return ERR_PTR(-ENOMEM);
txd = dmaengine_prep_slave_sg(chan, sgt->sgl, nents,
slave_dirn, DMA_CTRL_ACK);
txd = dmaengine_prep_slave_sg(chan, sgt->sgl, nents, dir, DMA_CTRL_ACK);
if (!txd) {
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
return ERR_PTR(-ENOMEM);
......@@ -651,12 +647,12 @@ ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
* unmapped.
*/
static void ep93xx_spi_dma_finish(struct ep93xx_spi *espi,
enum dma_data_direction dir)
enum dma_transfer_direction dir)
{
struct dma_chan *chan;
struct sg_table *sgt;
if (dir == DMA_FROM_DEVICE) {
if (dir == DMA_DEV_TO_MEM) {
chan = espi->dma_rx;
sgt = &espi->rx_sgt;
} else {
......@@ -677,16 +673,16 @@ static void ep93xx_spi_dma_transfer(struct ep93xx_spi *espi)
struct spi_message *msg = espi->current_msg;
struct dma_async_tx_descriptor *rxd, *txd;
rxd = ep93xx_spi_dma_prepare(espi, DMA_FROM_DEVICE);
rxd = ep93xx_spi_dma_prepare(espi, DMA_DEV_TO_MEM);
if (IS_ERR(rxd)) {
dev_err(&espi->pdev->dev, "DMA RX failed: %ld\n", PTR_ERR(rxd));
msg->status = PTR_ERR(rxd);
return;
}
txd = ep93xx_spi_dma_prepare(espi, DMA_TO_DEVICE);
txd = ep93xx_spi_dma_prepare(espi, DMA_MEM_TO_DEV);
if (IS_ERR(txd)) {
ep93xx_spi_dma_finish(espi, DMA_FROM_DEVICE);
ep93xx_spi_dma_finish(espi, DMA_DEV_TO_MEM);
dev_err(&espi->pdev->dev, "DMA TX failed: %ld\n", PTR_ERR(rxd));
msg->status = PTR_ERR(txd);
return;
......@@ -705,8 +701,8 @@ static void ep93xx_spi_dma_transfer(struct ep93xx_spi *espi)
wait_for_completion(&espi->wait);
ep93xx_spi_dma_finish(espi, DMA_TO_DEVICE);
ep93xx_spi_dma_finish(espi, DMA_FROM_DEVICE);
ep93xx_spi_dma_finish(espi, DMA_MEM_TO_DEV);
ep93xx_spi_dma_finish(espi, DMA_DEV_TO_MEM);
}
/**
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册