Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In pxa3xx_nand_sensing() instead of simply using info->is_ready
after issuing a command, the correct way of checking is to wait
for the device to be ready through the chip's waitfunc().
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The expected behavior of the waitfunc() NAND chip call is to wait
for the device to be READY (this is a standard chip line).
However, the current implementation does almost nothing, which opens
the possibility of issuing a command to a non-ready device.

Fix this by adding a new completion to wait for the ready event to arrive.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add a comment clarifying the use of pxa3xx_set_datasize() which is only
applicable on data read/write commands (i.e. commands with a data cycle,
such as READID, READ0, STATUS, etc.)
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

There's no need to privately store the device page size as it's
available in mtd structure field mtd->writesize.
Also, this removes the hardcoded page size value, leaving the
auto-detected value only.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Introduce a fifo_size field to represent the size of the controller's
FIFO buffer, and use it to distinguish that size from the amount
of data bytes to be read from the FIFO.

This is important to support devices with pages larger than the
controller's internal FIFO, that need to read the pages in FIFO-sized
chunks.

In particular, the current code is at least confusing, for it mixes
all the different sizes involved: FIFO size, page size and data size.

This commit starts the cleaning by removing the info->page_size field
that is not currently used. The host->page_size field should also
be removed and use always mtd->writesize instead. Follow up commits
will clean this up.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Whenever possible, it's always better to use the generic chip->cmdfunc
instead of the internal pxa3xx_nand_cmdfunc().
In this particular case, this will allow to have multiple cmdfunc()
implementations for different SoC variants.
Reviewed-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In order to customize early settings depending on the detected SoC variant,
move the detection to be before the nand_chip struct filling.

In a follow-up patch, this change is needed to detect the variant *before*
the call to alloc_nand_resource(), which allows to set a different cmdfunc()
for each variant.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

As per the ecc.read_page() prototype, we must return the maximum number
of bitflips that were corrected on any one region covering an ecc step.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The current driver doesn't support sub-page writing, so report
that to the NAND core.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Given there's no public specification to this date, and in order
to capture some important details and singularities about the
controller let's document them once and for good.

Cc: linux-doc@vger.kernel.org
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In commit:

  commit 62e8b851
  Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
  Date:   Fri Oct 4 15:30:38 2013 -0300

  mtd: nand: pxa3xx: Allocate data buffer on detected flash size

the way the buffer is allocated was changed: the first READ_ID is issued
with a small kmalloc'ed buffer. Only once the flash page size is detected
the DMA buffers are allocated, and info->use_dma is set.

Currently, if the device detection fails, the driver checks the 'use_dma'
module parameter and tries to release unallocated DMA resources.

Fix this by checking the proper indicator of the DMA allocation, which
is 'info->use_dma'.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This partially reverts c0f3b864.

The "armada370-nand" compatible support is not complete, and it was mistake
to add it. Revert it and postpone the support until the infrastructure is
in place.

Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This commit replaces the currently hardcoded buffer size, by a
dynamic detection scheme. First a small 256 bytes buffer is allocated
so the device can be detected (using READID and friends commands).

After detection, this buffer is released and a new buffer is allocated
to acommodate the page size plus out-of-band size.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Instead of setting info->dma each time a command is prepared,
we can move it after the DMA buffers are allocated.

This is more clear and it's the proper place to enable this, given
DMA cannot be turned on and off during runtime.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In a recent commit:

  commit f455578d
  Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
  Date:   Mon Aug 12 14:14:53 2013 -0300

  mtd: nand: pxa3xx: Remove hardcoded mtd name

  There's no advantage in using a hardcoded name for the mtd device.
  Instead use the provided by the platform_device.

The MTD name was changed to use the one provided by the platform_device.
However, this can be problematic as some users want to set partitions
using the kernel parameter 'mtdparts', where the name is needed.

Therefore, to avoid regressions in users relying in 'mtdparts' we revert
the change and use the previous one 'pxa3xx_nand-0'.

While at it, let's put a big comment and prevent this change from happening
ever again.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

There's no need to enclose this code within idef CONFIG_OF,
because the OF framework provides no-op stubs if CONFIG_OF=n.

Cc: devicetree@vger.kernel.org
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

When use_dma=0 there's no point in requesting resources for dma,
since they won't be used anyway. Therefore we remove that requirement,
therefore allowing devices without dma to pass the driver probe.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Now that we have added ARCH_HAS_DMA conditional the function
enable_int() may be unused. Declare it as __maybe_unused,
in order to remove the following warning, when the function is not used:

drivers/mtd/nand//pxa3xx_nand.c:343:24: warning: 'enable_int' defined
but not used [-Wunused-function]
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds a macro ARCH_HAS_DMA to compile-out arch specific
dma code, namely pxa_request_dma() and pxa_free_dma(). These symbols
are available only in pxa, which makes impossible to build the driver in
other platforms than ARCH_PXA.

In order to handle non-dma capable platforms, we implement a fallbacks that
allocate buffers as if 'use_dma=false', putting the dma related code
under the ARCH_HAS_DMA conditional.

Please note that the correct way to handle this is to migrate the
dma code to use of the mmp_pdma dmaengine driver. However, currently
this is not possible because the two dmaengine drivers can't work together.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This registers are not per-chip (aka host) but controller-wide,
so it's better to store them in the global 'info' structure.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the defined macros for NAND command instead of using a constant
internal structure. This commit is only a cleanup, there's no
functionality modification.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There's no advantage in using a hardcoded name for the mtd device.
Instead use the provided by the platform_device.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This is just a cosmetic change, to make the code more readable.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The ONFI command 'parameter page read' needs a non-standard length.
Therefore, we enable the 'length override' field in NDCB0 and set
a non-zero 'length count' in NDCB3.

Additionally, the 'spare enable' bit must be disabled for any command
that sets a non-zero 'length count' in NDCB3.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some newer controllers support a fourth command buffer. This additional
command buffer allows to set an arbitrary length count, using the
NDCB3.NDLENCNT field, to perform non-standard length operations
such as the ONFI parameter page read.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some commands (such as the ONFI parameter page read) need to
clear the 'spare enable' bit. This commit allows to set/clear
depending on the prepared command, instead of having it always
set.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

When ECC is not selected, the ECC enable bit must be cleared
in the NAND control register. Same applies to DMA.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This driver supports NFCv1 (as found in PXA SoC) and NFCv2 (as found in
Armada 370/XP SoC). As both controller has a few differences, a way of
distinguishing between the two is needed.

This commit introduces a new compatible string 'marvell,armada370-nand'
and assigns a compatible data of type enum pxa3xx_nand_variant to allow
such distinction.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This command is required to identify ONFI-compliant devices.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This allows to support READID ONFI command which sends 0x20
as address together with the 0x90 READID command.

This is required to detect ONFI compliant devices.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This module's device table is incorrectly declared using
i2c_pxa_dt_ids, instead of pxa3xx_nand_dt_ids.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch replaces cpu_is_pxa3xx() with of_machine_is_compatible()
which allows to build this driver for other platforms than ARCH_PXA.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Currently, the variable info->use_dma is never set and always
zero-valued which means the driver never does DMA transfers.
We fix this by simply setting info->use_dma to the module parameter,
also named 'use_dma'. Note that the module parameter has the same name,
but different semantics.

This fixes a regression introduced by the below commit
which removed the info->use_dma variable set.

  commit 4eb2da89
  Author: Lei Wen <leiwen@marvell.com>
  Date:   Mon Feb 28 10:32:13 2011 +0800

      mtd: pxa3xx_nand: unify prepare command

Before the above commit, the driver had use_dma=1 on all NAND commands
except on CMD_STATUS. This behavior is long lost and we are not
recovering in this patch, either.

This was spotted and verified by human inspection.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Reviewed-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Create a function to release the buffer and the dma channel, thus undoing
what pxa3xx_nand_init_buff() did. This commit makes the code more readable
and will allow to handle non-DMA capable platforms easier.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

clk_prepare_enable() can fail due to unknown reason.
Add a check for this and return the error code if it fails.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>