The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.12 and up
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The smiapp driver is the owner of the sub-devices exposed by the smiapp
driver. This prevents unloading the module whilst it's in use.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The sensor may be powered by either one of its sub-devices being accessed
from the user space (an open file handle) or by its s_power() op being
called with non-zero on argument. The driver counts the users and if any
reason to keep the device powered exists it will be powered.

However, a faulty condition was used in recognising the need to power off
the sensor, leading it to be powered off every time any of its uses went
away.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add device-tree support for mt9m111 camera sensor.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The basic API of rc-core used to be:

	dev = rc_allocate_device();
	dev->x = a;
	dev->y = b;
	dev->z = c;
	rc_register_device();

which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:

	dev = rc_allocate_device();
	dev->x = a;
	rc_set_allowed_protocols(dev, RC_BIT_X);
	dev->z = c;
	rc_register_device();

There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).

[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.

This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.

[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.

Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

X-Patchwork-Delegate: mchehab@redhat.com
Replace the custom I2C read/write implementation with SMBUS functions to
simplify the driver.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

X-Patchwork-Delegate: mchehab@redhat.com
The driver mistakenly prints the ROM version instead of the device ID to
the kernel log when detecting the chip. Fix it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The SMIA++ sensors are progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This switches all register accesses to use regmap. It allows to
use the regmap cache, tracing, and debug register dump facilities,
and removes the need to open code read-modify-writes.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for registering the sensor subdevice using the v4l2-async API.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

as are mt9v024 and mt9v034. With minimal changes it is possible
to support mt9v02[24] with the same driver.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The read mode register bits 8 and 9 are set and marked as reserved.
Don't clear them.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Since (min_row_time - crop->width) can be negative, we have to do a signed
comparison here. Otherwise max_t casts the negative value to unsigned int
and sets min_hblank to that invalid value.

Cc: stable@vger.kernel.org
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This driver moved over to v4l2_async_unregister_subdev()
but still retained a call to v4l2_unregister_subdev(). Remove.
Signed-off-by: NIan Molton <ian.molton@codethink.co.uk>
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Commit 0ba2aeb6 increased the internal control ranges
to 64 bit, but that caused problems in drivers that use the minimum/maximum/step/default_value
control values in a division or modulus operations since not all architectures support
those natively.

Luckily, in almost all cases it is possible to just cast to 32 bits (the control value
is known to be 32 bits, so it is safe to cast). Only in v4l2-ctrls.c was it necessary to
use do_div in one function.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.

The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values
for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase
the internal representation to 64 bits in preparation.

Because of these changes the msi3101 driver has been modified slightly
to fix a formatting issue (%d becomes %lld), vivi had to be modified
as well to cope with the new 64-bit min/max values and the PIXEL_RATE
control in a few sensor drivers required proper min/max/def values.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Update the recommended writes to those mentioned in the Rev 1.5 version of the
ADV7611 Register Settings Recommendations document released by Analog Devices.
The document does not mention why the recommended settings have been updated,
but presumably those are more fine tuned settings that can enhance performance
in some cases.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The I2C address of the sensor device was in the middle of the sub-device
name and not in the end as it should have been. The smiapp sub-device names
will change from e.g. "vs6555 1-0010 pixel array" to "vs6555 pixel array
1-0010".
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The include/media/s5p_fimc.h header has been removed in commit
49b2f4c5 ("exynos4-is: Remove support
for non-dt platforms"). This broke compilation of the m5mols driver.

Include the include/media/exynos-fimc.h header instead, which contains
the S5P_FIMC_TX_END_NOTIFY definition required by the driver.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The HPD GPIO is used as an output but its direction is never set. Fix
it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for the hsync-active, vsync-active and pclk-sample
properties to the DT bindings and control BT.656 mode implicitly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Parse the device tree node to populate platform data. Only the ADV7611
is currently support with DT.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

And set input routing when initializing the device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for optional GPIO-controlled HPD pins in addition to the
ADV7604-specific hotplug notifier.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This helps locating duplicates and inserting new headers.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The *_and_or() functions take an 'and' bitmask to be ANDed with the
register value before ORing it with th 'or' bitmask. As the functions
are used to mask and set bits selectively, this requires the caller to
invert the 'and' bitmask and is thus error prone. Replace those
functions with a *_clr_set() variant that takes a mask of bits to be
cleared instead of a mask of bits to be kept.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This one line function is called in a single location. Inline it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>