The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.12 and up
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Fix build errors in radio-miropcm20.c due to missing header file:

drivers/media/radio/radio-miropcm20.c: In function 'rds_waitread':
drivers/media/radio/radio-miropcm20.c:90:3: error: implicit declaration of function 'inb' [-Werror=implicit-function-declaration]
drivers/media/radio/radio-miropcm20.c: In function 'rds_rawwrite':
drivers/media/radio/radio-miropcm20.c:106:3: error: implicit declaration of function 'outb' [-Werror=implicit-function-declaration]
Reported-by: NJim Davis <jim.epost@gmail.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

It's also invalid when plane_no is equal to vb->num_planes
Signed-off-by: NZhaowei Yuan <zhaowei.yuan@samsung.com>
Cc: stable@vger.kernel.org      # for v3.7 and up
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Commit bd994ddb (vb2: Fix stream start and
buffer completion race) broke the buffer state check in vb2_buffer_done.

So accept all three possible states there since I can no longer tell the
difference between vb2_buffer_done called from start_streaming or from
elsewhere.

Instead add a WARN_ON at the end of start_streaming that will check whether
any buffers were added to the done list, since that implies that the wrong
state was used as well.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org      # for v3.15 and up
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Recently WARN_ON() calls have been added to warn if the driver is not
properly returning buffers to vb2 in start_streaming (if it fails) or
stop_streaming(). Add comments before those WARN_ON calls that refer
to the videobuf2-core.h header that explains what drivers are supposed
to do in these situations. That should help point developers in the
right direction if they see these warnings.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NPawel Osciak <pawel@osciak.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

sg_alloc_table_from_pages() only allocates a sg_table, so it should just use
GFP_KERNEL, not gfp_flags. If gfp_flags contains __GFP_DMA32 then mm/sl[au]b.c
will call BUG_ON:

[  358.027515] ------------[ cut here ]------------
[  358.027546] kernel BUG at mm/slub.c:1416!
[  358.027558] invalid opcode: 0000 [#1] PREEMPT SMP
[  358.027576] Modules linked in: mt2131 s5h1409 tda8290 tuner cx25840 cx23885 btcx_risc altera_ci tda18271 altera_stapl videobuf2_dvb tveeprom cx2341x videobuf2_dma_sg dvb_core rc_core videobuf2_memops videobuf2_core nouveau zr36067 videocodec v4l2_common videodev media x86_pkg_temp_thermal cfbfillrect cfbimgblt cfbcopyarea ttm drm_kms_helper processor button isci
[  358.027712] CPU: 19 PID: 3654 Comm: cat Not tainted 3.16.0-rc6-telek #167
[  358.027723] Hardware name: ASUSTeK COMPUTER INC. Z9PE-D8 WS/Z9PE-D8 WS, BIOS 5404 02/10/2014
[  358.027741] task: ffff880897c7d960 ti: ffff88089b4d4000 task.ti: ffff88089b4d4000
[  358.027753] RIP: 0010:[<ffffffff81196040>]  [<ffffffff81196040>] new_slab+0x280/0x320
[  358.027776] RSP: 0018:ffff88089b4d7ae8  EFLAGS: 00010002
[  358.027787] RAX: ffff880897c7d960 RBX: 0000000000000000 RCX: ffff88089b4d7b50
[  358.027798] RDX: 00000000ffffffff RSI: 0000000000000004 RDI: ffff88089f803b00
[  358.027809] RBP: ffff88089b4d7bb8 R08: 0000000000000000 R09: 0000000100400040
[  358.027821] R10: 0000160000000000 R11: ffff88109bc02c40 R12: 0000000000000001
[  358.027832] R13: ffff88089f8000c0 R14: ffff88089f803b00 R15: ffff8810bfcf4be0
[  358.027845] FS:  00007f83fe5c0700(0000) GS:ffff8810bfce0000(0000) knlGS:0000000000000000
[  358.027858] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  358.027868] CR2: 0000000001dfd568 CR3: 0000001097d5a000 CR4: 00000000000407e0
[  358.027878] Stack:
[  358.027885]  ffffffff81198860 ffff8810bfcf4be0 ffff880897c7d960 0000000000001b00
[  358.027905]  ffff880897c7d960 0000000000000000 ffff8810bfcf4bf0 0000000000000000
[  358.027924]  0000000000000000 0000000100000100 ffffffff813ef84a 00000004ffffffff
[  358.027944] Call Trace:
[  358.027956]  [<ffffffff81198860>] ? __slab_alloc+0x400/0x4e0
[  358.027973]  [<ffffffff813ef84a>] ? sg_kmalloc+0x1a/0x30
[  358.027985]  [<ffffffff81198f17>] __kmalloc+0x127/0x150
[  358.027997]  [<ffffffff813ef84a>] ? sg_kmalloc+0x1a/0x30
[  358.028009]  [<ffffffff813ef84a>] sg_kmalloc+0x1a/0x30
[  358.028023]  [<ffffffff813eff84>] __sg_alloc_table+0x74/0x180
[  358.028035]  [<ffffffff813ef830>] ? sg_kfree+0x20/0x20
[  358.028048]  [<ffffffff813f00af>] sg_alloc_table+0x1f/0x60
[  358.028061]  [<ffffffff813f0174>] sg_alloc_table_from_pages+0x84/0x1f0
[  358.028077]  [<ffffffffa007c3f9>] vb2_dma_sg_alloc+0x159/0x230 [videobuf2_dma_sg]
[  358.028095]  [<ffffffffa003d55a>] __vb2_queue_alloc+0x10a/0x680 [videobuf2_core]
[  358.028113]  [<ffffffffa003e110>] __reqbufs.isra.14+0x220/0x3e0 [videobuf2_core]
[  358.028130]  [<ffffffffa003e79d>] __vb2_init_fileio+0xbd/0x380 [videobuf2_core]
[  358.028147]  [<ffffffffa003f563>] __vb2_perform_fileio+0x5b3/0x6e0 [videobuf2_core]
[  358.028164]  [<ffffffffa003f871>] vb2_fop_read+0xb1/0x100 [videobuf2_core]
[  358.028184]  [<ffffffffa06dd2e5>] v4l2_read+0x65/0xb0 [videodev]
[  358.028198]  [<ffffffff811a243f>] vfs_read+0x8f/0x170
[  358.028210]  [<ffffffff811a30a1>] SyS_read+0x41/0xb0
[  358.028224]  [<ffffffff818f02e9>] system_call_fastpath+0x16/0x1b
[  358.028234] Code: 66 90 e9 dc fd ff ff 0f 1f 40 00 41 8b 4d 68 e9 d5 fe ff ff 0f 1f 80 00 00 00 00 f0 41 80 4d 00 40 e9 03 ff ff ff 0f 1f 44 00 00 <0f> 0b 66 0f 1f 44 00 00 44 89 c6 4c 89 45 d0 e8 0c 82 ff ff 48
[  358.028415] RIP  [<ffffffff81196040>] new_slab+0x280/0x320
[  358.028432]  RSP <ffff88089b4d7ae8>
[  358.032208] ---[ end trace 6443240199c706e4 ]---
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.13 and up
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

add the following IDs
USB_PID_PCTV_78E (0x025a) for PCTV 78e
USB_PID_PCTV_79E (0x0262) for PCTV 79e

For these it9135 devices.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

IT9135 RF tuner clock is coming from demodulator. We need enable it
early in demod init, before any tuner I/O. Currently it is enabled
by tuner driver itself, but it is too late and performance will be
reduced as some registers are not updated correctly. Clock is
disabled automatically when demod is put onto sleep.

Cc: <stable@vger.kernel.org> # v3.15+
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That register is needed to program very first in order to operate
correctly.

[crope@iki.fi: returned sequence back, removed sleep, moved reg
write earlier to prevent populating tuner ops in case of failure]

Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: NBimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Update IT9135 BX tuner config 60 and 61 inittabs.

[crope@iki.fi: removed two reg writes from driver init itself]
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: NBimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We should not select SPI bus when sub-driver auto-select is
selected. That option is meant for auto-selecting all possible
ancillary drivers used for selected board driver. Ancillary
drivers should define needed dependencies itself.

I2C and I2C_MUX are still selected here for a reason described on
commit 347f7a37

Reverts commit e4462ffcReported-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This was caused by an uninitialized setup.config field.

Based on a suggestion from Devin Heitmueller.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Reported-by: NScott Robinson <scott.robinson55@gmail.com>
Tested-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.10 and up
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The smiapp driver is the owner of the sub-devices exposed by the smiapp
driver. This prevents unloading the module whilst it's in use.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The sensor may be powered by either one of its sub-devices being accessed
from the user space (an open file handle) or by its s_power() op being
called with non-zero on argument. The driver counts the users and if any
reason to keep the device powered exists it will be powered.

However, a faulty condition was used in recognising the need to power off
the sensor, leading it to be powered off every time any of its uses went
away.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Remove the now unnecessary memset too.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sometimes dev->tuner_type is compared to UNSET, sometimes to TUNER_ABSENT,
but these defines have different values.

Standardize to TUNER_ABSENT.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

make reset control optional for i.MX27

The patch "[media] coda: add reset control support" introduced a build failure
if CONFIG_RESET_CONTROLLER is disabled:

    drivers/media/platform/coda.c:3734:2: error: implicit declaration of
     function 'devm_reset_control_get'

Since not all SoCs containing CODA VPUs do have a system reset controller,
use devm_reset_control_get_optional to make it optional.
Reported-by: NShawn Guo <shawn.guo@linaro.org>
Reported-by: NOlof's autobuilder <build@lixom.net>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes the following sparse warnings:

drivers/media/radio/radio-miropcm20.c:193:33: warning:
 Using plain integer as NULL pointer
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch add the DT support for Atmel ISI driver.
It use the same v4l2 DT interface that defined in video-interfaces.txt.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Now the platform data is initialized by allocation of isi
structure. In the future, we use pdata to store the dt parameters.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for devicetree probe for the rcar-vin
driver.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
[g.liakhovetski@gmx.de fix a typo, sort headers alphabetically]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add device-tree support to pxa_camera host driver.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
[g.liakhovetski@gmx.de: added of_node_put()]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add device-tree support for mt9m111 camera sensor.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add initial support for OF based soc-camera devices that may be used
by any of the soc-camera drivers. The driver itself will need converting
to use OF.

These changes allow the soc-camera driver to do the connecting of any
async capable v4l2 device to the soc-camera driver. This has currently
been tested on the Renesas Lager board.

It currently only supports one input device per driver as this seems
to be the standard connection for these devices.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
[g.liakhovetski@gmx.de add check for multiple subdevices]
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Tested-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Since we have get vdev by calling video_devdata() at the beginning of
s5p_mfc_open(), we should just use vdev instead of calling video_devdata()
again in the following code.
Signed-off-by: NZhaowei Yuan <zhaowei.yuan@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Take into account limitations specific to the Exynos3250 SoC,
regarding setting the chroma subsampling control's value.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

JPEG codec on Exynos3250 SoC produces broken raw image if a JPEG
image is decoded to YUV420 format and downscaled by a factor
greater than 2. Prevent this by asserting downscale ratio to 2.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Assure proper crop_rect initialization in case the user space
doesn't call S_SELECTION ioctl.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

V4L2_SEL_TGT_COMPOSE_DEFAULT switch case should select whole
available area of the image and V4L2_SEL_TGT_COMPOSE
should apply user settings.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The jpeg_bound_align_image function needs to know the context
in which it is called, as it needs to align image dimensions in
a slight different manner for Exynos3250, which crops pixels for
specific values in case the format is RGB.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When parsing JPEG header s5p_jpeg_parse_hdr function
should return immediately in case there was an error
while reading a byte.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds support for jpeg codec on Exynos3250 SoC to
the s5p-jpeg driver. Supported raw formats are: YUYV, YVYU, UYVY,
VYUY, RGB565, RGB565X, RGB32, NV12, NV21. The support includes
also scaling and cropping features.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

On a normal condition, no errors should happen at xc5000
firmware upload is done. So, print at the dmesg if something
bad happens.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Currently, firmware retry logic keeps reading from FS every
time during the retry logic. This is not needed. Instead,
only release the firmware read after success.

While here, make the non-debug messages less verbose, as it
only matters to the user if the firmware was successfully
loaded, or if some error happened.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

With the current code, if something bad happens during the
firmware init process, the device will keep trying forever,
and removing it would cause an OOPS.

Instead, try only a limited amount of time. If not, fails.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

HVR-950Q uses an I2C remote controller at address 0x47 (7-bits
notation). Add support for it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The IR dprintk message that prints a RC5 decoding failure
is not much helpful, as it doesn't tell on what bit the
error occurred.

Add such information, in order to make the debug message
more useful.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

On some hardware (au0828/au8522), the hardware is broken with
regards to the initial pulse detection. So, the driver needs to
produce a fake start pulse. That limits the acceptable protocols,
as it is not possible to produce a fake pulse that would cover
all supported protocols.

So, allow the driver to explicitly set the allowed protocols.

If the driver doesn't specify, keep the old behavior.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Commits 21dc61d3 and 7a1dd50b reduced the board I2C
speed to 20 MHz by default, due to a I2C stretch issue:
while xc5000 uses i2c stretch when a command is sent to it,
au0828 doesn't support this feature.

However, this is needed only for Xceive tuners. The other
I2C devices can work at the max speed.

So, revert the workarounds at board level, handling it at
I2C level, only when talking with xc5000.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>