- 17 4月, 2008 27 次提交
-
-
由 Kumar Gala 提交于
When we moved to arch/powerpc we actively tried to avoid using the ppc_md.setup_io_mappings(). Currently no board ports use it so let's remove it to avoid any new boards using it. Also, remove early_serial_map() since we don't even have a call out for it in arch/powerpc. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Michael Ellerman 提交于
There is logic in platforms/peries/lpars.c which checks if the user has specified a console on the command line, and refrains from adding a preferred console entry for the hvc/hvsi console if they have. This trips up if you use "netconsole=foo" on the command line, and has the result that you get _only_ the netconsole, because the hvc device is never added as a preferred console. Worse still if you get the netconsole configuration wrong somehow, you end up with no console at all. As it turns out we don't need to worry about checking the command line. If the user has specified "console=foo", then foo will be set as the preferred console when the command line is parsed in start_kernel(), much later than the pseries code, and so the latter setting will take effect. Signed-off-by: NMichael Ellerman <michael@ellerman.id.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Michael Ellerman 提交于
Move the prototype for find_udbg_vterm() into pseries.h, removing it from setup.c. Signed-off-by: NMichael Ellerman <michael@ellerman.id.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Manish Ahuja 提交于
This changes the way we calculate how much space to reserve for the pHyp dump. Currently we reserve 256MB only. With this change, the code first checks to see if an amount has been specified on the boot command line with the "phyp_dump_reserve_size" option, and if so, uses that much. Otherwise it computes 5% of total ram and rounds it down to a multiple of 256MB, and uses the larger of that or 256MB. This is for large systems with a lot of memory (10GB or more). The aim is to have more space available for the kernel on reboot on machines with more resources. Although the dump will be collected pretty fast and the memory released really early on allowing the machine to have the full memory available, this alleviates any issues that can be caused by having way too little memory on very very large systems during those few minutes. Signed-off-by: NManish Ahuja <mahuja@us.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
* Removed defines KERNEL_PGD_PTRS & USER_PGD_PTRS since they aren't used anywhere * Changed pmd_page macro to use pfn_to_page so we get proper behavior if ARCH_PFN_OFFSET is set as well if we use a different memory model on ppc32. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
Now that we properly set the physical address in the program header of the vmlinux ELF we can extract it to properly set the load and entry point for u-boot uImages. Before we always hard coded the load & entry point to 0. However there are situations that the kernel may be built with a non-zero physical address. We use objdump to extract the PHDR. We assume that there is only one PHDR in the vmlinux of type LOAD. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
We can set LOAD_OFFSET and use the AT attribute on sections and the linker will properly set the physical address of the LOAD program header for us. This allows us to know how the PHYSICAL_START the user configured a kernel with by just looking at the resulting vmlinux ELF. This is pretty much stolen from how x86 does things in their linker scripts. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
Moved phys_addr_t out of mmu-*.h and into asm/types.h so we can use it in places that before would have caused recursive includes. For example to use phys_addr_t in <asm/page.h> we would have included <asm/mmu.h> which would have possibly included <asm/mmu-hash64.h> which includes <asm/page.h>. Wheeee recursive include. CONFIG_PHYS_64BIT is a bit counterintuitive in light of ppc64 systems and thus the config option is only used for ppc32 systems with >32-bit physical addresses (44x, 85xx, 745x, etc.). Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
* PAGE_OFFSET is not always the start of code, use _stext instead. * grab PAGE_SIZE and KERNELBASE from asm/page.h like ppc64 does. Makes the code a bit more common and provide a single place to manipulate the defines for things like kdump. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
We always use __initial_memory_limit as an address so rename it to be clear. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
Now that we have a proper variable that is the address of the top of low memory we can use it to limit the lmb allocations. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
* Determine the RPN we are running the kernel at runtime rather than using compile time constant for initial TLB * Cleanup adjust_total_lowmem() to respect memstart_addr and be a bit more clear on variables that are sizes vs addresses. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
total_lowmem represents the amount of low memory, not the physical address that low memory ends at. If the start of memory is at 0 it happens that total_lowmem can be used as both the size and the address that lowmem ends at (or more specifically one byte beyond the end). To make the code a bit more clear and deal with the case when the start of memory isn't at physical 0, we introduce lowmem_end_addr that represents one byte beyond the last physical address in the lowmem region. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
A number of users of PPC_MEMSTART (40x, ppc_mmu_32) can just always use 0 as we don't support booting these kernels at non-zero physical addresses since their exception vectors must be at 0 (or 0xfffx_xxxx). For the sub-arches that support relocatable interrupt vectors (book-e), it's reasonable to have memory start at a non-zero physical address. For those cases use the variable memstart_addr instead of the #define PPC_MEMSTART since the only uses of PPC_MEMSTART are for initialization and in the future we can set memstart_addr at runtime to have a relocatable kernel. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
There does not appear to be any reason that we shouldn't just have -Iarch/$(ARCH) on both ppc32 and ppc64 builds. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
Nothing appears to use BOOT_LOAD so remove it as a configurable option. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Adrian Bunk 提交于
This adds the missing MODULE_LICENSE("GPL"). Signed-off-by: NAdrian Bunk <bunk@kernel.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 David Woodhouse 提交于
Fedora 9 works on Efika without the separate 'device-tree supplement', thanks to the kernel's own fixups. With one exception -- because 'CHRP' still appears on the 'machine:' line in /proc/cpuinfo, the installer misdetects the platform and misconfigures yaboot, putting it into a PReP boot partition instead of in the /boot filesystem where the Efika's firmware could find it. The kernel's fixups for Efika already correct one instance of 'chrp', in the 'device_type' property. This fixes it in the 'CODEGEN,description' property too, since that's what's exposed to userspace in /proc/cpuinfo. Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Jochen Friedrich 提交于
This implements various helpers to support OF bindings for the i2c API. Signed-off-by: NJochen Friedrich <jochen@scram.de> Acked-by: NDavid S. Miller <davem@davemloft.net> Acked-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Anton Vorontsov 提交于
This implements support for the GPIO LIB API. Two calls are still unimplemented though: irq_to_gpio and gpio_to_irq. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Anton Vorontsov 提交于
This implements various helpers to support OF bindings for the GPIO LIB API. Previously this was PowerPC specific, but it seems this code isn't arch-dependent anyhow, so let's place it into of/. SPARC will not see this addition yet, real hardware seem to not use GPIOs at all. But this might change: http://www.leox.org/docs/faq_MLleon.html "16-bit I/O port" sounds promising. :-) Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
The iSeries veth driver uses an on-stack struct completion that it initializes using the COMPLETION_INITIALIZER instead of COMPLETION_INITIALIZER_ONSTACK macro, causing problems with lockdep. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
This fixes the handling of the preempt count when switching interrupt stacks so that HW interrupt properly get the softirq mask copied over from the previous stack. It also initializes the softirq stack preempt_count to 0 instead of SOFTIRQ_OFFSET, like x86, as __do_softirq() does the increment, and we hit some lockdep checks if we have it twice. That means we do run for a little while off the softirq stack with the preempt-count set to 0, which could be deadly if we try to take a softirq at that point, however we do so with interrupts disabled, so I think we are ok. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
Currently, we initialize the "current" pointer in the PACA (which is used by the "current" macro in the kernel) before calling setup_system(). That means that early_setup() is called with current still "NULL" which is -not- a good idea. It happens to work so far but breaks with lockdep when early code calls printk. This changes it so that all PACAs are statically initialized with __current pointing to the init task. For non-0 CPUs, this is fixed up before use. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Ishizaki Kou 提交于
This fixes a potential bug at drivers/char/hvc_beat.c. - hvc_put_term_char routine will decrement "rest" variable twice, and forget to advance "buf" pointer by "nlen" bytes. This bug was not hit previously because the output handler in drivers/char/hvc_console.c splits given output into 16 bytes at maximum. Reported-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Ishizaki Kou 提交于
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Paul Mackerras 提交于
-
- 16 4月, 2008 2 次提交
-
-
由 Jerone Young 提交于
This changes the cpu_idle loop for 44x platforms to utilize the Wait Enable feature of the CPU. This helps virtulization solutions know when the guest Linux kernel is in an idle state. A command line option called "idle" is also added to allow people to change the idle loop back to the original variation. This is done by setting "idle=spin" on the kernel command line. Signed-off-by: NJerone Young <jyoung5@us.ibm.com> Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
-
由 Josh Boyer 提交于
Add a multi-board PowerPC 40x defconfig file Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
-
- 15 4月, 2008 11 次提交
-
-
由 Josh Boyer 提交于
Board specific defconfigs are useful, however with the ability to do multi-board defconfigs they aren't needed in the top level configs directory. Move the 4xx board specific defconfigs to individual directories under arch/powerpc/configs. Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
-
由 Paul Mackerras 提交于
There is a potential bug in __lmb_alloc_base where we subtract `size' from the base address of a reserved region without checking whether the subtraction could wrap around and produce a very large unsigned value. In fact it probably isn't possible to hit the bug in practice since it would only occur in the situation where we can't satisfy the allocation request and there is a reserved region starting at 0. This fixes the potential bug by breaking out of the loop when we get to the point where the base of the reserved region is less than the size requested. This also restructures the loop to be a bit easier to follow. The same logic got copied into lmb_alloc_nid_unreserved, so this makes a similar change there. Here the bug is more likely to be hit because the outer loop (in lmb_alloc_nid) goes through the memory regions in increasing order rather than decreasing order as __lmb_alloc_base does, and we are therefore more likely to hit the case where we are testing against a reserved region with a base address of 0. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Paul Mackerras 提交于
This makes no semantic changes. It fixes the whitespace and formatting a bit, gets rid of a local DBG macro and uses the equivalent pr_debug instead, and restructures one while loop that had a function call and assignment in the condition to be a bit more readable. Some comments about functions being called with relocation disabled were also removed as they would just be confusing to most readers now that the code is in lib/. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 David S. Miller 提交于
A variant of lmb_alloc() that tries to allocate memory on a specified NUMA node 'nid' but falls back to normal lmb_alloc() if that fails. The caller provides a 'nid_range' function pointer which assists the allocator. It is given args 'start', 'end', and pointer to integer 'this_nid'. It places at 'this_nid' the NUMA node id that corresponds to 'start', and returns the end address within 'start' to 'end' at which memory assosciated with 'nid' ends. This callback allows a platform to use lmb_alloc_nid() in just about any context, even ones in which early_pfn_to_nid() might not be working yet. This function will be used by the NUMA setup code on sparc64, and also it can be used by powerpc, replacing it's hand crafted "careful_allocation()" function in arch/powerpc/mm/numa.c If x86 ever converts it's NUMA support over to using the LMB helpers, it can use this too as it has something entirely similar. Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Stephen Rothwell 提交于
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Stephen Rothwell 提交于
pmi.h does not diectly reference anything in of_device.h and of the two files that include asm/pmi.h, one includes of_device.h and the other includes of_platform.h (which includes of_device.h). Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Stephen Rothwell 提交于
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Stephen Rothwell 提交于
Now that we have the alpaca, the reg_save_ptr is no longer needed in the paca. Eradicate all global uses of it and make it static in the iSeries lpardata.c Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Stephen Rothwell 提交于
The iSeries HV only needs the first two fields of the paca statically initialised, so create an alternate paca that contains only those and switch to our real paca immediately after boot. This is in order to make the 1024 cpu patches easier since they will no longer have to statically initialise the pacas for iSeries. Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Dale Farnsworth 提交于
The prpmc2800 platform requires a zImage formatted file with an embedded dtb file. Rename the requested boot image file to dtbImage.prpmc2800. Signed-off-by: NDale Farnsworth <dale@farnsworth.org> Acked-by: NMark A. Greer <mgreer@mvista.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Dale Farnsworth 提交于
Add the device tree bindings for the Marvell mv64x60 series of system controller chips in booting-without-of.text. Signed-off-by: NDale Farnsworth <dale@farnsworth.org> Acked-by: NMark A. Greer <mgreer@mvista.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-