[POWERPC] Implement support for the GPIO LIB API

This implements support for the GPIO LIB API.  Two calls are still
unimplemented though: irq_to_gpio and gpio_to_irq.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Documentation/powerpc/booting-without-of.txt

@@ -88,6 +88,10 @@ Table of Contents
     3) OpenPIC Interrupt Controllers
     4) ISA Interrupt Controllers
 
+  VIII - Specifying GPIO information for devices
+    1) gpios property
+    2) gpio-controller nodes
+
   Appendix A - Sample SOC node for MPC8540
 
 
@@ -3431,6 +3435,54 @@ encodings listed below:
 	2 =  high to low edge sensitive type enabled
 	3 =  low to high edge sensitive type enabled
 
+VIII - Specifying GPIO information for devices
+==============================================
+
+1) gpios property
+-----------------
+
+Nodes that makes use of GPIOs should define them using `gpios' property,
+format of which is: <&gpio-controller1-phandle gpio1-specifier
+		     &gpio-controller2-phandle gpio2-specifier
+		     0 /* holes are permitted, means no GPIO 3 */
+		     &gpio-controller4-phandle gpio4-specifier
+		     ...>;
+
+Note that gpio-specifier length is controller dependent.
+
+gpio-specifier may encode: bank, pin position inside the bank,
+whether pin is open-drain and whether pin is logically inverted.
+
+Example of the node using GPIOs:
+
+	node {
+		gpios = <&qe_pio_e 18 0>;
+	};
+
+In this example gpio-specifier is "18 0" and encodes GPIO pin number,
+and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller.
+
+2) gpio-controller nodes
+------------------------
+
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+
+Example of two SOC GPIO banks defined as gpio-controller nodes:
+
+	qe_pio_a: gpio-controller@1400 {
+		#gpio-cells = <2>;
+		compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank";
+		reg = <0x1400 0x18>;
+		gpio-controller;
+	};
+
+	qe_pio_e: gpio-controller@1460 {
+		#gpio-cells = <2>;
+		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+	};
 
 Appendix A - Sample SOC node for MPC8540
 ========================================

arch/powerpc/Kconfig

@@ -81,6 +81,11 @@ config GENERIC_FIND_NEXT_BIT
 	bool
 	default y
 
+config GENERIC_GPIO
+	bool
+	help
+	  Generic GPIO API support
+
 config ARCH_NO_VIRT_TO_BUS
 	def_bool PPC64
 

include/asm-powerpc/gpio.h

+/*
+ * Generic GPIO API implementation for PowerPC.
+ *
+ * Copyright (c) 2007-2008  MontaVista Software, Inc.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __ASM_POWERPC_GPIO_H
+#define __ASM_POWERPC_GPIO_H
+
+#include <linux/errno.h>
+#include <asm-generic/gpio.h>
+
+#ifdef CONFIG_HAVE_GPIO_LIB
+
+/*
+ * We don't (yet) implement inlined/rapid versions for on-chip gpios.
+ * Just call gpiolib.
+ */
+static inline int gpio_get_value(unsigned int gpio)
+{
+	return __gpio_get_value(gpio);
+}
+
+static inline void gpio_set_value(unsigned int gpio, int value)
+{
+	__gpio_set_value(gpio, value);
+}
+
+static inline int gpio_cansleep(unsigned int gpio)
+{
+	return __gpio_cansleep(gpio);
+}
+
+/*
+ * Not implemented, yet.
+ */
+static inline int gpio_to_irq(unsigned int gpio)
+{
+	return -ENOSYS;
+}
+
+static inline int irq_to_gpio(unsigned int irq)
+{
+	return -EINVAL;
+}
+
+#endif /* CONFIG_HAVE_GPIO_LIB */
+
+#endif /* __ASM_POWERPC_GPIO_H */