As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file.  Move the
AR8035 support into the main imx6qdl-microsom file.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The regulators node is redundant, and serves no useful function.
Remove it from i.MX6 SolidRun platforms.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

UDOO board has a possibility to disable most of imx6 SoC power supplies via
"EN_5V" signal, which is connected to "NANDF_D4" pad.

This reduces current consumption after shutdown from ~350 mA to ~40 mA and
prevents a SoC watchdog from starting it again on its own after the
watchdog timeout expires (previously it was not possible to shut down the
SoC permanently if its watchdog was ever enabled since it was still ticking
after the shutdown).

Unfortunately, this does not extinguish the "Power" LED (as it is powered
from an always-on voltage regulator).

To power the SoC up again press the power button (SW2, the one with a long
shaft).
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

As explained in Documentation/devicetree/bindings/net/fsl-fec.txt the
phy-reset-gpios is active high only if the 'phy-reset-active-high' is
present.

As 'phy-reset-active-high' is not used here, fix the device tree
description by passing GPIO_ACTIVE_LOW flag.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Tested-by: NPatrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

On imx6qdl-sabreauto the HDMI DDC bus is connected to I2C2, so
pass the 'ddc-i2c-bus' property accordingly.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for PCIe support.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Currently the imx pci driver fails to probe on i.MX6SX.

Fix the PCI representation so that the driver can be probed and
PCI devices can be detected.

Tested on a im6sx-sdb board:

00:00.0 Class 0604: 16c3:abcd
01:00.0 Class 0280: 8086:08b1
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.

This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Commit a22950c8 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Ls1021a esdhc had been enabled in uboot,
but it had not been enabled it in kernel,
So set the esdhc's status to "okay".
Signed-off-by: Nyinbo.zhu <yinbo.zhu@nxp.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The two Ethernet switches have an AT24C512 each. This is a 64K device,
not 512 bytes as currently listed in the device tree.
Reported-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.

Fixes the following warning in i.MX dts files:

Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This renames the audio device to "Front" in order to match the RDU2
naming, which makes it easier for a unified userspace to deal with
both boards.

Also rename the phandle for the headphone amplifier to more closely
resemble the RDU2 DTS.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Reviewed-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

There are 0 ohm resistors that allow selecting the EDID I2C port to
be I2C1 or I2C2.

On revd1 the 0 ohm resistors are populated in such a way that the I2C2
is used as DDC I2C bus, so fix it accordingly.
Reported-by: NLuís Mendes <luis.p.mendes@gmail.com>
Suggested-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx7s/imx7d has the ptp interrupt newly added as well.

For imx7, "int0" is the interrupt for queue 0 and ENET_MII
"int1" is for queue 1
"int2" is for queue 2

For imx6sx, "int0" handles all 3 queues and ENET_MII

And of course, the "pps" interrupt is for the PTP_CLOCK_PPS interrupts
This will help document what each interrupt does.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This is needed for the bootloader to patch in the correct MAC address.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The following build warning is seen with W=1:

Warning (unit_address_vs_reg): Node /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has a unit name, but no reg property

Fix this warning by adding reg property from such node and, consequently,
includes a mdio node into the fec node, with the 'address-cells' and
'size-cells' to avoid these other following warnings:

Warning (reg_format): "reg" property in /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Signed-off-by: NMarco Franchi <marco.franchi@nxp.com>
Tested-by: NLothar Waßmann <LW@karo-electronics.de>
Acked-by: NLothar Waßmann <LW@karo-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add QSPI node support, and this function is disabled by default
This setting could be overwritten in board-level definitions
Signed-off-by: NSZ Lin <sz.lin@moxa.com>
Acked-by: NLi Yang <leoyang.li@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.

Fixes the following warning in nspire dts files:

Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

We have phy-cells for usb_phy0, but it's missing for usb_phy1 and we get:

Warning (phys_property): Missing property '#phy-cells' in node
/ocp/l4ls@48000000/control@140000/usb-phy@1b00 or bad phandle
(referred from /ocp/usb@47400000/usb@47401800:phys[0])
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like the interrupt property is missing the controller and level
information causing:

Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: NTony Lindgren <tony@atomide.com>

"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.

Fixes the following warning in Marvell dts files:

Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

commit 200a575b ("ARM: dts: meson: organize devices in their corresponding busses")
organized all peripherals in busses so that the base register offset of
the bus doesn't have to be included in all child-nodes anymore.
The GPIO interrupt controller however specifies the register offset
without subtracting the "cbus" base address. This leads to a problem
where of_iomap inside the irq-meson-gpio driver fails because it
actually tries to map 0x182209880 (cbus base = 0xc1100000 + 0xc1109880
for the GPIO interrupt controller). Fix this by using 0x9880 as register
offset.

Fixes: 7d32bc03 ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Nodes are sorted by their register start address. Move gpio_intc to the
correct position.
No functional changes intended.

Fixes: 7d32bc03 ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This reverts commit 5b725054.

The rtc block on i.MX53 is a completely different hardware than the
one found on i.MX25.

Cc: <stable@vger.kernel.org> #4.14
Reported-by: NNoel Vellemans <Noel.Vellemans@visionbms.com>
Suggested-by: NJuergen Borleis <jbe@pengutronix.de>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

at24mac602 should be at the I2C address 0x50, so that it matches the
'reg' property.

Fixes: d4cd1581 ("ARM: dts: vf610-zii-dev: Add .dts file for rev. C")
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes the following warnings:

arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000

arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The pin assignment for the wl127x interrupt was incorrect.  I am
not sure how this every worked.  This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.

Fixes: ab8dd3ae ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working.  This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.

Fixes: 44e47164 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.

This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.

Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.

Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.

Fixes: 7136d457 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Booting a kernel results in the kernel warning us about the following
PPI interrupts configuration:
[    0.105127] smp: Bringing up secondary CPUs ...
[    0.110545] GIC: PPI11 is secure or misconfigured
[    0.110551] GIC: PPI13 is secure or misconfigured

Fix this by using the appropriate edge configuration for PPI11 and
PPI13, this is similar to what was fixed for Northstar (BCM5301X) in
commit 0e34079c ("ARM: dts: BCM5301X: Correct GIC_PPI interrupt
flags").

Fixes: 7b2e987d ("ARM: NSP: add minimal Northstar Plus device tree")
Fixes: 1a9d53ca ("ARM: dts: NSP: Add TWD Support to DT")
Acked-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.

Fixes: 70725d6e ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c376 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

With the latest dtc, we get many warnings about the missing
'#reset-cells' property in these controllers, e.g.:

arch/arm/boot/dts/r8a7790-lager.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /can@e6e80000:resets[0])
arch/arm/boot/dts/r8a7792-blanche.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/dma-controller@e6700000:resets[0])
arch/arm/boot/dts/r8a7792-wheat.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/ethernet@e6800000:resets[0])
arch/arm/boot/dts/r8a7793-gose.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /gpio@e6050000:resets[0])
arch/arm/boot/dts/r8a7794-alt.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /i2c@e6500000:resets[0])
arch/arm/boot/dts/r8a7794-silk.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /interrupt-controller@e61c0000:resets[0])

This adds it for the three r8a779x chips that were lacking it. The
binding mandates this as <1>, so this is the value I use.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[geert: Add fix for r8a7793.dtsi]
Fixes: 34fbd2b1 ("ARM: dts: r8a7790: Add reset control properties")
Fixes: 6e11a322 ("ARM: dts: r8a7792: Add reset control properties")
Fixes: 84fb19e1 ("ARM: dts: r8a7793: Add reset control properties")
Fixes: 615beb75 ("ARM: dts: r8a7794: Add reset control properties")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch fixes the DTC warnings about missing property #phy-cells.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NEric Anholt <eric@anholt.net>

Add remote-wakeup-connected for omap OHCI as that's needed by
ohci-platform driver.

Cc: devicetree@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

"ti,am335x-usb-phy" is using the phy binding, but is missing #phy-cells
property. Fixes the following warning in TI dts files:

Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>