If kzalloc() fails exit with -ENOMEM.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

MS Windows mounts removable storage in "Removal optimized mode" by
default. All the writes to the media are synchronous which is achieved
by setting FUA (Force Unit Access) bit in SCSI WRITE(10,12) commands.
This prevents I/O requests aggregation in block layer dramatically
decreasing performance.

This patch brings an option to accept or ignore mentioned bit
 a) via specifying module parameter "nofua", or
 b) through sysfs entry
	/sys/devices/platform/_UDC_/gadget/gadget-lunX/nofua
	(_UDC_ is the name of the USB Device Controller driver)

Patch is based on the work that was done by Denis Karpov for Maemo 5
platform.
Signed-off-by: NAndy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Bring a strict way to get the 'ro' parameter from the user.

The patch followed by this one adds another boolean parameter. To be consistent
Michał Nazarewicz proposed to use simple_strtol() in both cases (correspondend
discussion in LKML [1]). Due to simple_strtol() doesn't return error in a good
way and we have a boolean parameter the strict_strtoul() is used.

[1] http://lkml.org/lkml/2010/7/14/169Signed-off-by: NAndy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Enable isochronous urb enqueue.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Isochronous endpoint needs a bigger size of transfer ring. Isochronous URB
consists of multiple packets, each packet needs a isoc td to carry, and
there will be multiple trbs inserted to the ring at one time. One segment
is too small for isochronous endpoints, and it will result in
room_on_ring() check failure and the URB is failed to enqueue.

Allocate bigger ring for isochronous endpoint. 8 segments should be enough.
This will be replaced with dynamic ring expansion in the future.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch implements isochronous urb enqueue and interrupt handler part.

When an isochronous urb is passed to xHCI driver, first check the transfer
ring to guarantee there is enough room for the whole urb. Then update the
start_frame and interval field of the urb. Always assume URB_ISO_ASAP
is set, and never use urb->start_frame as input.

The number of isoc TDs is equal to urb->number_of_packets. One isoc TD is
consumed every Interval. Each isoc TD consists of an Isoch TRB chained to
zero or more Normal TRBs.

Call prepare_transfer for each TD to do initialization; then calculate the
number of TRBs needed for each TD. If the data required by an isoc TD is
physically contiguous (not crosses a page boundary), then only one isoc TRB
is needed; otherwise one or more additional normal TRB shall be chained to
the isoc TRB by the host.

Set TRB_IOC to the last TRB of each isoc TD. Do not ring endpoint doorbell
to start xHC procession until all the TDs are inserted to the endpoint
transer ring.

In irq handler, update urb status and actual_length, increase
urb_priv->td_cnt. When all the TDs are completed(td_cnt is equal to
urb_priv->length), giveback the urb to usbcore.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add urb_priv data structure to xHCI driver. This structure allows multiple
xhci TDs to be linked to one urb, which is essential for isochronous
transfer. For non-isochronous urb, only one TD is needed for one urb;
for isochronous urb, the TD number for the urb is equal to
urb->number_of_packets.

The length field of urb_priv indicates the number of TDs in the urb.
The td_cnt field indicates the number of TDs already processed by xHC.
When td_cnt matches length, the urb can be given back to usbcore.

When an urb is dequeued or cancelled, add all the unprocessed TDs to the
endpoint's cancelled_td_list. When process a cancelled TD, increase
td_cnt field. When td_cnt equals urb_priv->length, giveback the
cancelled urb.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds mechanism to process Missed Service Error Event.
Sometimes the xHC is unable to process the isoc TDs in time, it will
generate Missed Service Error Event. In this case some TDs on the ring are
not processed and missed. When encounter a Missed Servce Error Event, set
the skip flag of the ep, and process the missed TDs until reach the next
processed TD, then clear the skip flag.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds new cases to trb_comp_code switch, and moves
the switch judgment ahead of fetching td.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove redundant print messages in the interrupt context.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the bulk and interrupt td processing part in
handle_tx_event() into a separate function process_bulk_intr_td().
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the ctrl td processing part in handle_tx_event()
into a separate function process_ctrl_td().
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the td universal processing part in handle_tx_event()
into a separate function finish_td().

if finish_td() returns 1, it indicates the urb can be given back.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch adds Huawei ETS 1220 product id into the list of supported
devices in 'option' usb serial driver.
Signed-off-by: NPavel Kazlou <p.i.kazlou@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Logitech Harmony 700 series needs an extra delay during
initialization.  This patch adds a USB quirk which enables such a delay
and adds the device to the quirks list.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Enlarging the buffer size via the MON_IOCT_RING_SIZE ioctl causes
general protection faults. It appears the culprit is an incorrect
argument to mon_free_buff: instead of passing the size of the current
buffer being freed, the size of the new buffer is passed.

Use the correct size argument to mon_free_buff when changing the size of
the buffer.
Signed-off-by: NSteven Robertson <steven@strobe.cc>
Acked-by: NPete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removed entry referencing g_eth_ffs.c file from Makefile.
The file never existed and the line was a leftover from a
developing process.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1409) removes some dead code from the ehci-hcd
scheduler.  Thanks to the previous patch in this series, stream->depth
is no longer used.  And stream->start and stream->rescheduled
apparently have not been used for quite a while, except in some
statistics-reporting code that never gets invoked.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1408) rearranges the scheduling code in ehci-hcd, partly
to improve its structure, but mainly to change the way it works.
Whether or not a transfer exceeds the hardware schedule length will
now be determined by looking at the last frame the transfer would use,
instead of the first available frame following the end of the transfer.

The benefit of this change is that it allows the driver to accept
valid URBs which would otherwise be rejected.  For example, suppose
the schedule length is 1024 frames, the endpoint period is 256 frames,
and a four-packet URB is submitted.  The four transfers would occupy
slots that are 0, 256, 512, and 768 frames past the current frame
(plus an extra slop factor).  These don't exceed the 1024-frame limit,
so the URB should be accepted.  But the current code notices that the
next available slot would be 1024 frames (plus slop) in the future,
which is beyond the limit, and so the URB is rejected unnecessarily.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1407) fixes a bug in ehci-hcd's isochronous scheduler.
All its calculations should be done in terms of microframes, but for
full-speed devices, sched->span is stored in frames.  It needs to be
converted.

This fix is liable to expose problems in other drivers.  The old code
would accept URBs that should not have been accepted, so drivers have
had no reason to avoid submitting URBs that exceeded the maximum
schedule length.  In an attempt to partially compensate for this, the
patch also adjusts the schedule length from a minimum of 256 frames up
to a minimum of 512 frames.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1406) adds a micro-optimization to ehci-hcd's scheduling
code.  Instead of computing remainders with respect to the schedule
length, use bitwise-and (which is quicker).  We know that the schedule
length will always be a power of two, but the compiler doesn't have
this information.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1405) fixes a small bug in ehci-hcd's isochronous
scheduler.  Not all EHCI controllers are PCI, and the code shouldn't
assume that they are.  Instead, introduce a special flag for
controllers which need to delay iso scheduling for full-speed devices
beyond the scheduling threshold.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: David Brownell <david-b@pacbell.net>
CC: stable <stable@kernel.org>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Enable MSI/MSI-X supporting in xhci driver.

Provide the mechanism to fall back using MSI and Legacy IRQs
if MSI-X IRQs register failed.
Signed-off-by: NDong Nguyen <Dong.Nguyen@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>,
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ulpi_set_vbus and ulpi_set_flags are using ULPI_SET(register) to write
to the PHY's registers, which means we can only set bits in the PHY's
register and not clear them.
By directly using the address of the register without any offset, we
now get the expected behaviour for these functions.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
 

If the write download record failed we shouldn't return 0.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CONFIG_ARCH_KARO doesn't exist in Kconfig and is never defined anywhere
else, therefore removing all references for it from the source code.
Signed-off-by: NChristian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Usb serial port device is child of its usb interface device, so
we can enable async suspend of usb serial port device to speedup
system suspend.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a patch for the musb usb controller.

It allows forwarding of the debug mode feature to its gadget in order
to be able to act as an ehci debug device.

This patch has been tested on an IGEPv2 board running a 2.6.35-rc1
kernel.
Signed-off-by: NStephane Duverger <stephane.duverger@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a patch that implements an USB EHCI Debug Device using the
Gadget API. This patch applies to a 2.6.35-rc3 kernel.

The gadget needs a compliant usb controller that forwards the
USB_DEVICE_DEBUG_MODE feature to its gadget.

The gadget provides two configuration modes, one that only printk() the
received data, and one that exposes a serial device to userland
(/dev/ttyGSxxx).

The gadget has been tested on an IGEPv2 board running a 2.6.35-rc1
kernel. The debug port was fed on the host side by a 2.6.34 kernel.
Signed-off-by: NStephane Duverger <stephane.duverger@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.

None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.

Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.

file=$1
name=$2
if grep -q lock_kernel ${file} ; then
    if grep -q 'include.*linux.mutex.h' ${file} ; then
            sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
    else
            sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
    fi
    sed -i ${file} \
        -e "/^#include.*linux.mutex.h/,$ {
                1,/^\(static\|int\|long\)/ {
                     /^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);

} }"  \
    -e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
    -e '/[      ]*cycle_kernel_lock();/d'
else
    sed -i -e '/include.*\<smp_lock.h\>/d' ${file}  \
                -e '/cycle_kernel_lock()/d'
fi
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed several coding style issues in freecom.c.
Signed-off-by: NMartin Enderleit <menderleit@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is no reason for the DMA channel program to override the
DMA mode passed down by its caller. Use the passed parameter
directly, and let the caller handle the decision on which mode
is to be used.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This pin-muxing is best done in the board files. The driver should
not do this explicitly.

Also, this code causes a warning to be thrown when OMAP2430 and OMAP3/4
support are enabled in the same kernel.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently devices don't get detected automatically if the ehci
module is inserted 2nd time onward. We need to disconnect and
reconnect the device for it to get detected and enumerated.

Resetting the USB PHY using PHY reset comamnd over ULPI fixes
this issue. Tested on OMAP3EVM.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>