drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_good_ack_health':
drivers/net/wireless/iwlwifi/iwl-rx.c:647: error: 'struct iwl_priv' has no member named '_agn'
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need "sdata" any more after:
	d84f3234
	mac80211: remove dev_hold/put calls
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In nl80211.h, be a little more elaborate in the docs for the definitions
NL80211_ATTR_CQM_RSSI_THOLD and NL80211_ATTR_CQM_RSSI_HYST.
Reported-by: NLuis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware  if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.

For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.

Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.

An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.

The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Auto auth mode is enabled by default. If user doesn't specify the
auth mode, while association driver will first try with open mode
and then with shared key mode. If user specifies an auth mode,
auto auth is disabled and driver will not try association with
another auth mode.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: NDaniel Ngu <daniel.dy.ngu@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is based on a RFC patch by Kalle Valo.

The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.

Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.

Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change local functions that are cast to iw_handler to
the more standard use with "union iwreq_data *wrqu"
so the iw_handler array no longer needs the casts.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use IW_HANDLER from wireless.h instead
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use #define IW_HANDLER from wireless.h instead
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert direct uses of [ (foo - SIOCIWFIRST) , fn)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a wireless.h macro for this, might as well use it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a wireless.h macro for this, might as well use it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These two #defines use the same value, but
SIOCIWFIRST makes more sense in this use.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Copied the idea from orinoco
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changed platform_device to be allocated dynamically from the
wl1271_alloc_hw function. Also cleaned up error handling in the
wl1271_alloc_hw function and module probe functions.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removing the wl1271 from the inet addr notifier chain sometimes causes the
registered handler to be called - causing locking problems if the removing
function is called from within the mutex.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The null func template is not needed for ad-hoc, and it's generation is not
supported for ad-hoc (mac80211 will WARN about it.)
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for the filters configured by the mac80211 stack.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removed duplicate code from wl1271_sdio module remove function. For
freeing stuff in the remove function wl1271_free_hw function is now
used.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added separate flag for SDIO debugging. Previously it has used
DEBUG_SPI flag. This patch also includes couple indentation fixes.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's no longer needed.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes MAC address handling. To achieve this, firmware booting had
to be delayed from the previous op_start to op_add_interface, which is the point
when the driver gets to know the configured MAC address. As the wl1271 only
supports one virtual interface, this even seems quite logical.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1271 supports U-APSD similarly as wl1251, so let's enable it.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "wl1271: implement WMM" accidentally used CONF_PS_SCHEME_LEGACY_PSPOLL,
but instead CONF_PS_SCHEME_LEGACY should be used as earlier.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Needed for U-APSD.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we get probe request from mac80211, we can remove two functions.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 now can create pspoll and nullfunc templates, better to use those.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Everything is ready now and we can enable WMM in wl1271.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a sysfs file to control the state of the BT co-ex (enable or disable it.)
By default, the BT co-ex is enabled.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to get the platform device for both SPI and SDIO, move the platform
device registration to wl1271_main.c from wl1271_spi.c.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add configuration values for the varous WLAN-BT co-ex configuration parameters,
and finally enable WLAN-BT co-ex. Based on preliminary measurements, it
appears the co-ex feature is not increasing WLAN power consumption, if BT
is not activated.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bluetooth coexistence (SG) configuration messages have changed and
were completely wrong. For instance, intending to enable the SG, it was
instead disabled.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changed driver to keep MMC host claimed while wlan interface is up.
This keeps MMC stack from powering the SDIO device down.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added method for wlan power control to io_ops struct and moved
wl1271_power_on and wl1271_power_off functions to wl1271_io.h.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The per-queue TX opportunity value is configured by the mac80211 in units
of 32us. The firmware however wants it in us, so add the conversion.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Features:

 * Station mode
 * IBSS mode
 * Monitor mode
 * Legacy support
 * HT support
 * TX/RX 11n Aggregation
 * HW encryption
 * LED
 * Suspend/Resume

For more information: http://wireless.kernel.org/en/users/Drivers/ath9k_htcSigned-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Without this you will get a panic if the device initialization
fails. Also, free ath_hw instance properly. ath9k_hw_deinit()
shouldn't do it.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>