The cdc_ncm driver still has a few places where stack variables are
passed to the cdc_ncm_do_request function.  This triggers a stack trace in
lib/dma-debug.c if the CONFIG_DEBUG_DMA_API option is set.

Adjust these calls to pass parameters that have been allocated with
kzalloc.
Signed-off-by: NJosh Boyer <jwboyer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan.  In promiscuous mode the filter table is cleared to in
order to disable filtering.  However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it.  As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.

CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the Manageability Engine (ME) is enabled on 82579, it periodically
accesses some MAC CSR registers.  There is an arbiter in hardware which
prevents simultaneous access of these registers by the host software, i.e.
the driver.  There is a hardware bug in the aribter that signals a host
access of the registers later than it actually happens.  A write of the
Transmit or Receive Descriptor Tail register could result in an incorrect
value if the driver and ME perform simultaneous accesses which could result
in an access to an invalid memory address.  This would return an
Unsupported Request which could hang the hardware.  Workaround the issue by
checking the FWSM register bit24 which is set by ME before it accesses the
MAC CSR registers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The MAC can drop short packets when the PHY detects noise on the line at
100Mbps due to a timing issue.  Workaround the issue by increasing the PLL
counter so the PHY properly recognizes the synchronization pattern from the
MAC.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On 82577/8/9 in half-duplex when a received packet is passed from the PHY
to the MAC, if too many preamble octects are stripped from the packet
before arriving at the MAC, it can be misintrepeted as an in-band message
rather than an actual frame.  For example, if the frame contents resembled
an interrupt request in-band message, it would trigger a false interrupt.
In most cases, the packet is just dropped.

By reducing the number of preamble octets stripped from the beginning of
the frame when passing it from the PHY to the MAC, the MAC will interpret
the frame properly.

An additional uses of the magic PHY_REG(770, 16) have been updated with a
define introduced with this patch.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to fix a memory leak found via code review for FCOE.
Specifically on DDP flows the SKBs were being dropped without being
recycled, freed, or given to the stack.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
  dt: add empty of_get_property for non-dt

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
  USB: Serial: Add PID(0xF7C0) to FTDI SIO driver for a zeitcontrol-device
  USB: Serial: Add device ID for Sierra Wireless MC8305
  USB: Serial: Added device ID for Qualcomm Modem in Sagemcom's HiLo3G
  usb/host/pci-quirks.c: correct annotation of `ehci_dmi_nohandoff_table'
  USB: option driver: add PID for Vodafone-Huawei K4511
  USB: option driver: add PID for Vodafone-Huawei K4510
  USB: option driver: add PID for Vodafone-Huawei K3771
  USB: option driver: add PID for Vodafone-Huawei K3770
  usb: serial: ftdi_sio.c: For the FT232H FTDI_SIO_SET_BAUDRATE_REQUEST, index needs to be shifted too
  usb/isp1760: Added missing call to usb_hcd_check_unlink_urb() during unlink
  USB: EHCI: Fix test mode sequence
  USB: ftdi_sio: fix minor typo in get_ftdi_divisor
  USB: at91_udc: include linux/prefetch.h explicitly
  USB: usb-storage: unusual_devs entry for ARM V2M motherboard.
  usb/ehci-mxc: add missing inclusion of mach/hardware.h
  USB: assign instead of equal in usbtmc.c
  usb: renesas_usbhs: fixup usbhsg_for_each_uep 1st pos
  usb: renesas_usbhs: fix DMA build by including dma-mapping.h
  usb: gadget: net2272 - Correct includes
  usb: musb: fix oops on musb_gadget_pullup
  ...

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  zcache: Fix build error when sysfs is not defined
  zcache: Use div_u64 for 64-bit division
  staging:rts_pstor: fix thread synchronization flow
  drivers:staging:solo6x10:add the missed slab.h
  staging: zcache: include module.h for MODULE_LICENSE
  drivers/staging/hv/blkvsc_drv.c: eliminate NULL pointer dereference
  Staging: Add clk API note to nvec/TODO
  drivers/staging/ath6kl/miscdrv/ar3kps/ar3kpsparser.c: adjust array index
  staging: more missing slab.h inclusions
  drivers/staging/solo6x10/p2m.c needs slab.h
  drivers/staging/solo6x10/core.c needs slab.h
  drivers/staging/dt3155v4l/dt3155v4l.c needs slab.h
  drivers/staging/speakup/devsynth.c: fix "buffer size is not provably correct" error
  Staging: iio: add some unlocks to raw_read() functions
  staging: ft1000_proc needs asm/io.h for inw/outw on sparc
  staging: rtl8192u: declare MODULE_FIRMWARE
  gma500: Fix clashes with DRM updates
  staging: zcache: module is GPL
  staging: fix zcache building

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-tip:
  x86-64: Rework vsyscall emulation and add vsyscall= parameter
  x86-64: Wire up getcpu syscall
  x86: Remove unnecessary compile flag tweaks for vsyscall code
  x86-64: Add vsyscall:emulate_vsyscall trace event
  x86-64: Add user_64bit_mode paravirt op
  x86-64, xen: Enable the vvar mapping
  x86-64: Work around gold bug 13023
  x86-64: Move the "user" vsyscall segment out of the data segment.
  x86-64: Pad vDSO to a page boundary

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: replace xfs_buf_geterror() with bp->b_error
  xfs: Check the return value of xfs_buf_read() for NULL
  "xfs: fix error handling for synchronous writes" revisited
  xfs: set cursor in xfs_ail_splice() even when AIL was empty
  xfs: Remove the macro XFS_BUFTARG_NAME
  xfs: Remove the macro XFS_BUF_TARGET
  xfs: Remove the macro XFS_BUF_SET_TARGET
  Replace the macro XFS_BUF_ISPINNED with helper xfs_buf_ispinned
  xfs: Remove the macro XFS_BUF_SET_PTR
  xfs: Remove the macro XFS_BUF_PTR
  xfs: Remove macro XFS_BUF_SET_START
  xfs: Remove macro XFS_BUF_HOLD
  xfs: Remove macro XFS_BUF_BUSY and family
  xfs: Remove the macro XFS_BUF_ERROR and family
  xfs: Remove the macro XFS_BUF_BFLAGS

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
  ARM: mmp: Change the way we use timer 0 as clockevent timer.
  ARM: mmp: Switch to using timer 1 as clocksource timer.
  ARM: mmp: Also start timer 1 on boot.
  ARM: pxa168/gplugd: free correct GPIO
  ARM: pxa168/gplugd: get rid of mfp-gplugd.h
  ARM: pxa: fix logic error in PJ4 iWMMXt handling
  mach-sa1100: fix PCI build problem
  omap: timer: Set dmtimer used as clocksource in autoreload mode
  OMAP3: am3517crane: remove NULL board_mux from board file
  arm: mach-omap2: mux: use kstrdup()
  arch:arm:plat-omap:iovmm: remove unused variable 'va'
  Update Nook Color machine 3284 to common Encore name
  am3505/3517: Various platform defines for UART4
  OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
  OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
  iMX: Fix build for iMX53
  ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
  OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
  OMAP3: beagle: don't touch omap_device internals
  OMAP1: enable GENERIC_IRQ_CHIP
  ...

Since we just checked bp for NULL, it is ok to replace
xfs_buf_geterror() with bp->b_error in these places.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NAlex Elder <aelder@sgi.com>

Check the return value of xfs_buf_read() for NULL and return ENOMEM
if it is NULL.  This is necessary in a few spots to avoid subsequent
code blindly dereferencing the null buffer pointer.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NAlex Elder <aelder@sgi.com>

Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  e1000e: increase driver version number
  e1000e: alternate MAC address update
  e1000e: do not disable receiver on 82574/82583
  e1000e: alternate MAC address does not work on device id 0x1060
  PCnet: Fix section mismatch
  bnx2x: disable dcb on 578xx since not supported yet
  bnx2x: properly clean indirect addresses
  bnx2x: prevent race between undi_unload and load flows
  bnx2x: fix select_queue when FCoE is disabled
  bnx2x: init FCOE FP only once
  ipv4: some rt_iif -> rt_route_iif conversions
  net/bridge/netfilter/ebtables.c: use available error handling code
  net/netlabel/netlabel_kapi.c: add missing cleanup code
  net/irda: sh_sir: tidyup compile warning
  net/irda: sh_sir: add missing header
  net/irda: sh_irda: add missing header
  slcan: ldisc generated skbs are received in softirq context
  scm: Capture the full credentials of the scm sender
  tcp: initialize variable ecn_ok in syncookies path
  drivers/net/wireless/wl1251: add missing kfree
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Don't do hypervisor calls on non-sun4v in DS driver.

Reported-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just like files-layout, blocks & objects layouts are part of the
NFS 4.1 protocol and should be automatically selected if NFS_4_1
is selected. The small problem is that these depend on other
Kernel support being present, while files only depends on NFS
itself.

This patch removes from the user choice the presence of objects
and blocks layout. But makes sure these are selected only if
the depended subsystems are present in the Kernel.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NPeng Tao <peng_tao@emc.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit df5e6223 ("ext4: fix deadlock in ext4_symlink() in ENOSPC
conditions") recalculated the number of credits needed for a long
symlink, in the process of splitting it into two transactions.  However,
the first credit calculation under-counted because if selinux is
enabled, credits are needed to create the selinux xattr as well.

Overrunning the reservation will result in an OOPS in
jbd2_journal_dirty_metadata() due to this assert:

  J_ASSERT_JH(jh, handle->h_buffer_credits > 0);

Fix this by increasing the reservation size.
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Acked-by: N"Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit ae54870a ("ext3: Fix lock inversion in ext3_symlink()")
recalculated the number of credits needed for a long symlink, in the
process of splitting it into two transactions.  However, the first
credit calculation under-counted because if selinux is enabled, credits
are needed to create the selinux xattr as well.

Overrunning the reservation will result in an OOPS in
journal_dirty_metadata() due to this assert:

  J_ASSERT_JH(jh, handle->h_buffer_credits > 0);

Fix this by increasing the reservation size.
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Acked-by: N"Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If word 0x37 in the EEPROM is 0xFFFF _or_ 0x0000, then there is no
alternate MAC address in the EEPROM.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to a hardware erratum, the receiver on 82574 and 82583 should not be
stopped once it has been started.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This issue is present all the way back to 2.6.34 kernels.

CC: <stable@kernel.org>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeffrey Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The patch http://lkml.org/lkml/2003/7/13/226 introduced an RLIMIT_NPROC
check in set_user() to check for NPROC exceeding via setuid() and
similar functions.

Before the check there was a possibility to greatly exceed the allowed
number of processes by an unprivileged user if the program relied on
rlimit only.  But the check created new security threat: many poorly
written programs simply don't check setuid() return code and believe it
cannot fail if executed with root privileges.  So, the check is removed
in this patch because of too often privilege escalations related to
buggy programs.

The NPROC can still be enforced in the common code flow of daemons
spawning user processes.  Most of daemons do fork()+setuid()+execve().
The check introduced in execve() (1) enforces the same limit as in
setuid() and (2) doesn't create similar security issues.

Neil Brown suggested to track what specific process has exceeded the
limit by setting PF_NPROC_EXCEEDED process flag.  With the change only
this process would fail on execve(), and other processes' execve()
behaviour is not changed.

Solar Designer suggested to re-check whether NPROC limit is still
exceeded at the moment of execve().  If the process was sleeping for
days between set*uid() and execve(), and the NPROC counter step down
under the limit, the defered execve() failure because NPROC limit was
exceeded days ago would be unexpected.  If the limit is not exceeded
anymore, we clear the flag on successful calls to execve() and fork().

The flag is also cleared on successful calls to set_user() as the limit
was exceeded for the previous user, not the current one.

Similar check was introduced in -ow patches (without the process flag).

v3 - clear PF_NPROC_EXCEEDED on successful calls to set_user().
Reviewed-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf symbols: Check '/tmp/perf-' symbol file ownership
  perf sched: Usage leftover from trace -> script rename
  perf sched: Do not delete session object prematurely
  perf tools: Check $HOME/.perfconfig ownership
  perf, x86: Add model 45 SandyBridge support
  perf tools: Add support to install perf python extension
  perf tools: do not look at ./config for configuration
  perf tools: Make clean leaves some files
  perf lock: Dropping unsupported ':r' modifier
  perf probe: Fix coredump introduced by probe module option
  jump label: Reduce the cycle count by changing the link order
  perf report: Use ui__warning in some more places
  perf python: Add PERF_RECORD_{LOST,READ,SAMPLE} routine tables
  perf evlist: Introduce 'disable' method
  trace events: Update version number reference to new 3.x scheme for EVENT_POWER_TRACING_DEPRECATED
  perf buildid-cache: Zero out buffer of filenames when adding/removing buildid

Change to new git tree -
 (git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git).
Signed-off-by: NTracey Dent <tdent48227@gmail.com>
Acked-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit af9d220b.

It turns out that one was meant to be applied on top of the edac.git
tree in -next that has more i7core_edac changes, but that wasn't clear
in the original email.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NBorislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PNFS_BLOCK needs BLK_DEV_DM/MD, which is not a dependency for other
pnfs layout drivers. Seperate it out so others can still build when
BLK_DEV_DM/MD is not enabled.

Also change select to depends on to avoid build failures.
Reported-and-tested-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NPeng Tao <peng_tao@emc.com>
Acked-by: NBenny Halevy <bhalevy@tonian.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Building MIPS mtx1_defconfig results in:

  MODPOST 735 modules
WARNING: drivers/net/pcnet32.o(.devinit.text+0x11ec): Section mismatch in reference from the function pcnet32_probe_vlbus.constprop.22() to the variable .init.data:pcnet32_portlist
The function __devinit pcnet32_probe_vlbus.constprop.22() references
a variable __initdata pcnet32_portlist.
If pcnet32_portlist is only used by pcnet32_probe_vlbus.constprop.22 then
annotate pcnet32_portlist with a matching annotation.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>