The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the physical function (PF) is reset for any reason the statistics
collection in ixgbevf_update_stats needs to wait to update until after
the reset synchronization ensures that the PF driver is up and running
and is finished with its own reset.  Go ahead and clear the link flag to
indicate this when the control message from the PF is received.  The
reset synchronization and recovery in the watchdog task will eventually
set the link flag up when the PF has resumed.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use dev_info to log link up/down messages.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The out of tree driver and the in kernel driver should use the same
interrupt handling logic for mailbox interrupts.  The difference in
the handlers was causing dissimilar behavior between the two drivers
complicating debug and trouble shooting.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map.  To do this I have expanded the work done in the main loop by
pushing first into tx_buffer.  This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor.  The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo.  By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.

To do this I also needed to change the logic and/or drop some flags.  I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do.  Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb.  Instead we can just check the bitflag in the skb.

In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway.  Instead of doing that we can just
use context 0 for all descriptors.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads.  Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

IEEE DCBx has a mechanism to change the default user priority. In
the normal case the OS can handle this via cgroups, iptables, socket,
options etc.

With SR-IOV and direct assigned VF devices the default priority
needs to be set by the PF device so the inserted VLAN tag is
correct.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These are copying data into 16 char arrays.  They all specify that the
first string can't be more than 11 characters but once you add on the
"-rx-" and the NUL character there isn't space for the %d.

The first string is probably never going to be 11 characters, but if it
is then let's truncate the string instead of corrupting memory.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ioremap returns 'void __iomem *' type.

Fix the following build warnings:

drivers/net/ethernet/smsc/smc911x.c:2079:14: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2079:14:    expected unsigned int *addr
drivers/net/ethernet/smsc/smc911x.c:2079:14:    got void [noderef] <asn:2>*
drivers/net/ethernet/smsc/smc911x.c:2086:18: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2086:18:    expected void [noderef] <asn:2>*base
drivers/net/ethernet/smsc/smc911x.c:2086:18:    got unsigned int *addr
drivers/net/ethernet/smsc/smc911x.c:2091:25: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2091:25:    expected void volatile [noderef] <asn:2>*addr
drivers/net/ethernet/smsc/smc911x.c:2091:25:    got unsigned int *addr
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is heavy transmission traffic in the CPDMA, then Rx descriptors
memory is also utilized as tx desc memory looses all rx descriptors and the
driver stops working then.

This patch adds boundary for tx and rx descriptors in bd ram dividing the
descriptor memory to ensure that during heavy transmission tx doesn't use
rx descriptors.

This patch is already applied to davinci_emac driver, since CPSW and
davici_dmac shares the same CPDMA, moving the boundry seperation from
Davinci EMAC driver to CPDMA driver which was done in the following
commit

commit 86d8c07f
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date:   Tue Jan 3 05:27:47 2012 +0000

    net/davinci: do not use all descriptors for tx packets

    The driver uses a shared pool for both rx and tx descriptors.
    During open it queues fixed number of 128 descriptors for receive
    packets. For each received packet it tries to queue another
    descriptor. If this fails the descriptor is lost for rx.
    The driver has no limitation on tx descriptors to use, so it
    can happen during a nmap / ping -f attack that the driver
    allocates all descriptors for tx and looses all rx descriptors.
    The driver stops working then.
    To fix this limit the number of tx descriptors used to half of
    the descriptors available, the rx path uses the other half.

    Tested on a custom board using nmap / ping -f to the board from
    two different hosts.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The limition of imx6 internal bus cause fec can't achieve 1G perfomance.
There will be many packages lost because FIFO over run.

This patch enable pause frame flow control.

Before this patch
iperf -s -i 1
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
[  4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49773
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0- 1.0 sec  6.35 MBytes  53.3 Mbits/sec
[  4]  1.0- 2.0 sec  3.39 MBytes  28.5 Mbits/sec
[  4]  2.0- 3.0 sec  2.63 MBytes  22.1 Mbits/sec
[  4]  3.0- 4.0 sec  1.10 MBytes  9.23 Mbits/sec

ifconfig
   RX packets:46195 errors:1859 dropped:1 overruns:1859 frame:1859

After this patch
iperf -s -i 1

[  4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49757
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0- 1.0 sec  49.8 MBytes   418 Mbits/sec
[  4]  1.0- 2.0 sec  50.1 MBytes   420 Mbits/sec
[  4]  2.0- 3.0 sec  47.5 MBytes   399 Mbits/sec
[  4]  3.0- 4.0 sec  45.9 MBytes   385 Mbits/sec
[  4]  4.0- 5.0 sec  44.8 MBytes   376 Mbits/sec

ifconfig
   RX packets:2348454 errors:0 dropped:16 overruns:0 frame:0
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than use an extra #define for something that already exists, use the
kernel #define for the PTP port.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Acked-by: NJacob Keller <Jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To prevent a race condition where an skb has been saved to return the Tx
timestamp later and the driver is removed, add a check to determine if we
have an skb stored and, if so, free it.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Acked-by: NJacob Keller <Jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a check against possible Rx timestamp freezing in the hardware via
watchdog mechanism. This situation can occur when an Rx timestamp has been
latched, but the packet has been dropped because the Rx ring is full.

Whenever a packet comes in that should be timestamped, the Rx timestamp
gets latched into the hardware registers and we will store the jiffy value
in the rx_ring. The watchdog will keep track of his own jiffy timer
whenever there is no valid timestamp in the registers.

If the watchdog detects a valid timestamp in the registers, meaning that no
Rx packet has consumed it yet, it will check which time is most recent: the
last time in the watchdog or any time in the rx_rings. If the most recent
"event" was more than 5 seconds ago, it will flush the Rx timestamp and
print a warning message to the syslog.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJacob Keller <Jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When transmitting a packet that must return a Tx timestamp, a work item
gets scheduled to poll for the Tx timestamp being completed in hardware.
Add a timeout on this work item of 15 seconds from when the driver gets the
skb, after which it will stop polling. Report via stats and system log if
this occurs.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Acked-by: NJacob Keller <Jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable SW timestamping for situations where the user may prefer it over HW
timestamping or there may not be HW timestamping.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Acked-by: NJacob Keller <Jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of our adapters have internal sensors that report thermal data.  This
patch enables reporting of that data via sysfs.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of our devices have internal sensors for reporting thermal data.
This patch creates the interface to the sensors for exporting via sysfs.
Subsequent patch will actually export the data.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of our adapters have sensors on them accessible via i2c and a private
interface.  This patch implements the kernel interface for i2c to those sensors.
Subsequent patches will provide functions to export that data.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set.  Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the standard #defines for PCIe Capability ASPM fields.

Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits.  PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: e1000-devel@lists.sourceforge.net
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

bnx2x does an internal GRO pass but doesn't provide gso_segs, thus
breaking qdisc_pkt_len_init() in case ingress qdisc is used.

We store gso_segs in NAPI_GRO_CB(skb)->count, where tcp_gro_complete()
expects to find the number of aggregated segments.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 6f0333b8 ("r8169: use 50% less ram for RX ring") the rx
ring buffers are always copied making dirty_rx useless.
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup a set of conditional tests.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The removed code block is duplicated in e1000e_write_itr() so use that
instead.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

rx_long_byte_count can be removed since it is duplicated in rx_bytes
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(...  to printk(KERN_INFO ...

v2 - remove unnecessary "e1000e:" prefix as pointed out by Joe Perches
     since that produces a redundant "e1000e:" in the log message

Cc: Joe Perches <joe@perches.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

...discovered during code inspection.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When there is heavy traffic and the cable is pulled, the driver must reset
the adapter to flush the Tx queue in hardware.  This causes the reset path
to be scheduled and logs the message "Reset adapter" which could be mis-
interpreted as an error by the user.  Change how the reset path is invoked
for this scenario by using the same method done in an existing work-around
for 80003es2lan (i.e. set a flag and if the flag is set in the reset code
do not log the "Reset adapter" message since the reset is expected).

Re-name the FLAG_RX_RESTART_NOW to FLAG_RESTART_NOW since it is used for
resets in both the Rx and Tx specific code.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Energy Efficient Ethernet on 82579 and I217 should only be enabled if not
disabled by the user, if the link is full duplex and the link partner has
similar EEE capabilities (stored in different EMI registers on the two
different parts).

After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in
different EMI registers on the two different parts) to clear the count of
received Tx/Rx LPI indications.

Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate
the bit is valid starting with I82579 (released before I217).
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When connected to certain switches, the 82577 PHY might drop link
unexpectedly.  Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Extended Management Interface (EMI) registers are accessed by first
writing the EMI register offset to the EMI_ADDR regiter and then either
reading or writing the data to/from the EMI_DATA register.  Add helper
functions for performing these steps and convert existing EMI register
accesses accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>