Add the three leds on the sama5d2 Xplained board with their pinctrl node.
The blue led is positioned with the "heartbeat" trigger.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add commit message and adapt to newer kernel]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add the push button named "PB USER" with code 0x104. Associated pinctrl node is
also added.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

For USB gadget on port A (device mode):
- pin PA31 is configured as an input GPIO which triggers an interrupt when
  vbus is detected on USB port A.
- pin PB9 is configured as an output GPIO and set to low level so the
  board doesn't supply vbus to USB port A.

For USB host:
- pin PB10 is configured as an output GPIO and is active at high level.
  The ohci driver will activate this pin so the board supplies vbus to USB
  port B.
- pin PB9 should be configured as an output GPIO and active at high level
  to use to USB port A in host mode (conflicts with USB gadget).
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

All pinctrl nodes for the Atmel pinctrl controller need to have their
bias configuration explicitly defined. Otherwise, the pinctrl mapping
is not valid.

It works for now as the pinctrl driver proceeds even with invalid
mappings, but this can become an issue, if the pinctrl driver starts
to require valid mappings. Additionally, the pin is not protected from
being remapped later by an other driver.

There is an external 1kOhms pull-up to 3.3V, so no bias is required on
the Ethernet PHY's interrupt line.
Signed-off-by: NRomain Izard <romain.izard.pro@gmail.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

After 57a38eff (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.

The phy IRQ and associated pinmux node is also added.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed

Add pdmic node on sama5d2-xplained board.The pdmic
pins conflict with ISC_D0 & ISC_D1 data pins.
Signed-off-by: NSongjun Wu <songjun.wu@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Data have to be held longer for the PMIC device. The ACT8945A
datasheet claims that minimum SDA data hold time is about 300 ns.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add watchdog node to support SAMA5D4 watchdog.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add sdmmc and flexcom devices
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The clocks group properties and the clock@0 node are useless, remove them
to avoid copy pasting in future device trees.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add regulator nodes of PMIC ACT8945A chip on the board.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add device pin muxing for the sama5d2 Xplained board.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This commit adds the stdout-path property in /chosen for all Armada
boards that were not yet carrying this property, and gets rid of
/chosen/bootargs which becomes unneeded: earlyprintk should not be
used by default, and the console= parameter is replaced by the
/chosen/stdout-path property.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.

In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>

The Armada XP Matrix board has an Ethernet PHY that isn't configurable
through the MDIO bus, so we use the newly introduced fixed-link PHY DT
binding to represent the PHY of this platform and get network working.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the Armada 370/375/38x/XP SoC-level Device Tree files have
the proper "clocks" property in their UART controllers node, it is no
longer useful to have the clock-frequency property defined in the
board-level Device Tree files.

Therefore, this commit gets rid of all the useless 'clock-frequency'
properties.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1397806908-7550-5-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Since the Armada XP Matrix board has 4 GB of RAM and not 2 GB, we
update the Device Tree to take into account the correct amount of
memory. As noted in the new comment, the last 256 MB of RAM are in
fact not usable, due to the overlap with the MBus Window address
range.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada XP Matrix board is the mother board of a more complex
system. The mother board uses an Armada XP MV78460, 4 serial ports, 2
SATA ports, one Ethernet connection, a PCIe port and a USB port. All
those devices are enabled in the Device Tree added by this patch.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>