This patch adds miscellaneous files for the Altera Ethernet Driver,
including ethtool support.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the SGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the MSGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds devicetree support for the at86rf230 driver.

Possible gpios to configure are "reset-gpio" and "sleep-gpio".
Also add support to configure the "irq-type" for the irq polarity
register.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch make the reset pin optionally. Some devices like the atben
from qi-hardware don't have a reset pin externally. The usually way is
to turn power off/on for the atben device to initiate a device reset.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While checkpatch another patch I got a:

"WARNING: msleep < 20ms can sleep for up to 20ms"

The datasheet of at86rf231 and at86rf212 says a minimum delay for reset
pulse width and spi access latency after reset is 625 nanoseconds.

This patch removes the 1 milliseconds sleep and replace it with a 1
microseconds udelay which should be also okay for the reset pulse width.

To change the state from RESET -> TRX_OFF the at86rf230 device needs 120
microseconds, this is a worst case of all at86rf* chips.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to lock the clearing of IRQ_TRX_END in status.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix a unexpected state change for the at86rf231 chip.
We can't change into STATE_FORCE_TX_ON while the chip is in one of
SLEEP, P_ON, RESET, TRX_OFF, and all *_NOCLK states.

In this case we are in the TRX_OFF state. See datasheet [1] page 71 for
more information.

Without this patch you will get the following message on a at86rf231 device:

[   20.065218] unexpected state change: 8, asked for 4
[   20.070527] ------------[ cut here ]------------
[   20.075414] WARNING: CPU: 0 PID: 160 at net/mac802154/ieee802154_dev.c:43 mac802154_slave_open+0x70/0xb8()
[   20.085594] Modules linked in: autofs4
[   20.089667] CPU: 0 PID: 160 Comm: ifconfig Not tainted 3.14.0-20140108-1-00993-g905c192 #162
[   20.098612] [<c00127b8>] (unwind_backtrace) from [<c0010b1c>] (show_stack+0x10/0x14)
[   20.106819] [<c0010b1c>] (show_stack) from [<c0033838>] (warn_slowpath_common+0x60/0x80)
[   20.115311] [<c0033838>] (warn_slowpath_common) from [<c00338e8>] (warn_slowpath_null+0x18/0x20)
[   20.124590] [<c00338e8>] (warn_slowpath_null) from [<c057b7e8>] (mac802154_slave_open+0x70/0xb8)
[   20.133880] [<c057b7e8>] (mac802154_slave_open) from [<c0488a58>] (__dev_open+0xa8/0x108)
[   20.142553] [<c0488a58>] (__dev_open) from [<c0488cb0>] (__dev_change_flags+0x8c/0x148)
[   20.151051] [<c0488cb0>] (__dev_change_flags) from [<c0488d84>] (dev_change_flags+0x18/0x48)
[   20.159968] [<c0488d84>] (dev_change_flags) from [<c04e2e9c>] (devinet_ioctl+0x2b0/0x63c)
[   20.168623] [<c04e2e9c>] (devinet_ioctl) from [<c04712e4>] (sock_ioctl+0x23c/0x29c)
[   20.176727] [<c04712e4>] (sock_ioctl) from [<c00e3cb8>] (do_vfs_ioctl+0x4a8/0x578)
[   20.184671] [<c00e3cb8>] (do_vfs_ioctl) from [<c00e3dd4>] (SyS_ioctl+0x4c/0x78)
[   20.192402] [<c00e3dd4>] (SyS_ioctl) from [<c000da00>] (ret_fast_syscall+0x0/0x48)
[   20.200392] ---[ end trace 9a34542f4ea08e47 ]---

This patch was tested on at86rf231 and at86rf212.

[1] http://www.atmel.com/images/doc8111.pdfSigned-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we call netdev_*() under netif_msg_*() checks, we can fold these into
netif_*() macro invocations.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert dev_*(&ndev->dev, ...) to netdev_*(ndev, ...) calls since they are a bit
shorter and at the same time give more information on a device.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert pr_*() to netdev_*() calls as the latter provide info on a device.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Exit the driver's probe() method when the register layout is unknown as the
driver would cause kernel oops in this case anyway.

While at it, move the corresponding error message printout and convert it from
pr_err() to dev_err().
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.

All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.

There are problems with the netpoll packet receive code.  __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context.  netpoll_neigh_reply leaks every skb it receives.  Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).

Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.

Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.

Design:

cxgb4:

Direct ULD callback from the DB FULL/DROP interrupt handler.  This allows
the ULD to stop doing user DB writes as quickly as possible.

While user DB usage is disabled, the LLD will accumulate DB write events
for its queues.  Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count.  This reduces the
load put on the DB fifo when reenabling.

iw_cxgb4:

Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps.  This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs.  If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP.  Thus we allow the new driver to work with an older libcxgb4.

When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED.  As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events.  Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.

When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list.  This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example).  QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO.  Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain.  This prevents resuming to
quickly and overflowing the FIFO.  Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.

The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops.  As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the bh safe variant with the hard irq safe variant.

We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.

Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently it's using the wrong ETH_P_LOOP type, which is sometimes treated
as packet length instead of ether type (because it's 0x0060).

Use the new ETH_P_LOOPBACK type.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change all internal uses of ieee802154_addr_sa to ieee802154_addr,
except for those instances that communicate directly with userspace.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable sparse warnings about endianness, replace the remaining fields
regarding network operations without explicit endianness annotations
with such that are annotated, and propagate this through the entire
stack.

Uses of ieee802154_addr_sa are not changed yet, this patch is only
concerned with all other fields (such as address filters, operation
parameters and the likes).
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The struct as currently defined uses host byte order for some fields,
and most big endian/EUI display byte order for other fields. Inside the
stack, endianness should ideally match network byte order where possible
to minimize the number of byteswaps done in critical paths, but this
patch does not address this; it is only preparatory.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Linux 3.13, dma_set_mask_and_coherent was introduced, and we have
been encouraged to use it. It simplifies the DMA mapping code a bit as
well.

Change-ID: I66e340245af7d0dedfa8b40fec1f5e352754432e
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NCatherine Sullivan  <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that the 2.4 firmware reports the correct number of MSI-X vectors,
use this value correctly when communicating with the VF, and when
setting up the interrupt linked list.

The PF has always reported the correct number of MSI-X vectors, so we
should never increment the value in the vf driver.

Change-ID: Ifeefc631c321390192219ce2af9ada6180c1492f
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We have a separate handler for MDD events, a generic reset is not required.

Change-ID: I77858e2d479e4e65c52aede67109464649ea0253
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The FDIR replay logic was being run a little too soon (before the
queues were enabled) and hence the tail bump was not effective till
a later transaction happened on the queue.

Change-ID: Icfd7cd2e79fc3cae3cbd3f703a2b3a148b4e7bf6
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>