Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
10 个月 前同步成功

通知 149
Star 36
Fork 7
cloud-kernel
cloud-kernel

前往新版Gitcode，体验更适合开发者的 AI 搜索 >>

切换分支/标签
  1. 04 11月, 2018 12 次提交
    • D
      net/ipv6: Allow onlink routes to have a device mismatch if it is the default route · 6a4aa53a
      由 David Ahern 提交于 
      [ Upstream commit 4ed591c8ab44e711e56b8e021ffaf4f407c045f5 ]

The intent of ip6_route_check_nh_onlink is to make sure the gateway
given for an onlink route is not actually on a connected route for
a different interface (e.g., 2001:db8:1::/64 is on dev eth1 and then
an onlink route has a via 2001:db8:1::1 dev eth2). If the gateway
lookup hits the default route then it most likely will be a different
interface than the onlink route which is ok.

Update ip6_route_check_nh_onlink to disregard the device mismatch
if the gateway lookup hits the default route. Turns out the existing
onlink tests are passing because there is no default route or it is
an unreachable default, so update the onlink tests to have a default
route other than unreachable.

Fixes: fc1e64e1 ("net/ipv6: Add support for onlink flag")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      6a4aa53a
    • J
      openvswitch: Fix push/pop ethernet validation · 0024aeb0
      由 Jaime Caamaño Ruiz 提交于 
      [ Upstream commit 46ebe2834ba5b541f28ee72e556a3fed42c47570 ]

When there are both pop and push ethernet header actions among the
actions to be applied to a packet, an unexpected EINVAL (Invalid
argument) error is obtained. This is due to mac_proto not being reset
correctly when those actions are validated.

Reported-at:
https://mail.openvswitch.org/pipermail/ovs-discuss/2018-October/047554.html
Fixes: 91820da6 ("openvswitch: add Ethernet push and pop actions")
Signed-off-by: NJaime Caamaño Ruiz <jcaamano@suse.com>
Tested-by: NGreg Rose <gvrose8192@gmail.com>
Reviewed-by: NGreg Rose <gvrose8192@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      0024aeb0
    • T
      bonding: fix length of actor system · 655b0860
      由 Tobias Jungel 提交于 
      [ Upstream commit 414dd6fb9a1a1b59983aea7bf0f79f0085ecc5b8 ]

The attribute IFLA_BOND_AD_ACTOR_SYSTEM is sent to user space having the
length of sizeof(bond->params.ad_actor_system) which is 8 byte. This
patch aligns the length to ETH_ALEN to have the same MAC address exposed
as using sysfs.

Fixes: f87fda00 ("bonding: prevent out of bound accesses")
Signed-off-by: NTobias Jungel <tobias.jungel@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      655b0860
    • J
      vhost: Fix Spectre V1 vulnerability · 26ab2eb8
      由 Jason Wang 提交于 
      [ Upstream commit ff002269a4ee9c769dbf9365acef633ebcbd6cbe ]

The idx in vhost_vring_ioctl() was controlled by userspace, hence a
potential exploitation of the Spectre variant 1 vulnerability.

Fixing this by sanitizing idx before using it to index d->vqs.

Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      26ab2eb8
    • I
      rtnetlink: Disallow FDB configuration for non-Ethernet device · 2799b518
      由 Ido Schimmel 提交于 
      [ Upstream commit da71577545a52be3e0e9225a946e5fd79cfab015 ]

When an FDB entry is configured, the address is validated to have the
length of an Ethernet address, but the device for which the address is
configured can be of any type.

The above can result in the use of uninitialized memory when the address
is later compared against existing addresses since 'dev->addr_len' is
used and it may be greater than ETH_ALEN, as with ip6tnl devices.

Fix this by making sure that FDB entries are only configured for
Ethernet devices.

BUG: KMSAN: uninit-value in memcmp+0x11d/0x180 lib/string.c:863
CPU: 1 PID: 4318 Comm: syz-executor998 Not tainted 4.19.0-rc3+ #49
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0x14b/0x190 lib/dump_stack.c:113
  kmsan_report+0x183/0x2b0 mm/kmsan/kmsan.c:956
  __msan_warning+0x70/0xc0 mm/kmsan/kmsan_instr.c:645
  memcmp+0x11d/0x180 lib/string.c:863
  dev_uc_add_excl+0x165/0x7b0 net/core/dev_addr_lists.c:464
  ndo_dflt_fdb_add net/core/rtnetlink.c:3463 [inline]
  rtnl_fdb_add+0x1081/0x1270 net/core/rtnetlink.c:3558
  rtnetlink_rcv_msg+0xa0b/0x1530 net/core/rtnetlink.c:4715
  netlink_rcv_skb+0x36e/0x5f0 net/netlink/af_netlink.c:2454
  rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4733
  netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
  netlink_unicast+0x1638/0x1720 net/netlink/af_netlink.c:1343
  netlink_sendmsg+0x1205/0x1290 net/netlink/af_netlink.c:1908
  sock_sendmsg_nosec net/socket.c:621 [inline]
  sock_sendmsg net/socket.c:631 [inline]
  ___sys_sendmsg+0xe70/0x1290 net/socket.c:2114
  __sys_sendmsg net/socket.c:2152 [inline]
  __do_sys_sendmsg net/socket.c:2161 [inline]
  __se_sys_sendmsg+0x2a3/0x3d0 net/socket.c:2159
  __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2159
  do_syscall_64+0xb8/0x100 arch/x86/entry/common.c:291
  entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x440ee9
Code: e8 cc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
ff 0f 83 bb 0a fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fff6a93b518 EFLAGS: 00000213 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000440ee9
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000003
RBP: 0000000000000000 R08: 00000000004002c8 R09: 00000000004002c8
R10: 00000000004002c8 R11: 0000000000000213 R12: 000000000000b4b0
R13: 0000000000401ec0 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
  kmsan_save_stack_with_flags mm/kmsan/kmsan.c:256 [inline]
  kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:181
  kmsan_kmalloc+0x98/0x100 mm/kmsan/kmsan_hooks.c:91
  kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:100
  slab_post_alloc_hook mm/slab.h:446 [inline]
  slab_alloc_node mm/slub.c:2718 [inline]
  __kmalloc_node_track_caller+0x9e7/0x1160 mm/slub.c:4351
  __kmalloc_reserve net/core/skbuff.c:138 [inline]
  __alloc_skb+0x2f5/0x9e0 net/core/skbuff.c:206
  alloc_skb include/linux/skbuff.h:996 [inline]
  netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline]
  netlink_sendmsg+0xb49/0x1290 net/netlink/af_netlink.c:1883
  sock_sendmsg_nosec net/socket.c:621 [inline]
  sock_sendmsg net/socket.c:631 [inline]
  ___sys_sendmsg+0xe70/0x1290 net/socket.c:2114
  __sys_sendmsg net/socket.c:2152 [inline]
  __do_sys_sendmsg net/socket.c:2161 [inline]
  __se_sys_sendmsg+0x2a3/0x3d0 net/socket.c:2159
  __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2159
  do_syscall_64+0xb8/0x100 arch/x86/entry/common.c:291
  entry_SYSCALL_64_after_hwframe+0x63/0xe7

v2:
* Make error message more specific (David)

Fixes: 090096bf ("net: generic fdb support for drivers without ndo_fdb_<op>")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-and-tested-by: syzbot+3a288d5f5530b901310e@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+d53ab4e92a1db04110ff@syzkaller.appspotmail.com
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      2799b518
    • K
      Revert "net: simplify sock_poll_wait" · fd54c188
      由 Karsten Graul 提交于 
      [ Upstream commit 89ab066d4229acd32e323f1569833302544a4186 ]

This reverts commit dd979b4d.

This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      fd54c188
    • S
      net: udp: fix handling of CHECKSUM_COMPLETE packets · 4fb0dc97
      由 Sean Tranchetti 提交于 
      [ Upstream commit db4f1be3ca9b0ef7330763d07bf4ace83ad6f913 ]

Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.

udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.

Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.

Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);

Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.

This patch addresses this problem in two ways:
	1) Do not use the dev pointer when calling netdev_rx_csum_fault()
	   from skb_copy_and_csum_datagram_msg(). Since this gets called
	   from the UDP path where skb->dev has been overwritten, we have
	   no way of knowing if the pointer is still valid. Also for the
	   sake of consistency with the other uses of
	   netdev_rx_csum_fault(), don't attempt to call it if the
	   packet was checksummed by software.

	2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
	   If we receive a packet that's CHECKSUM_COMPLETE that fails
	   verification (i.e. skb->csum_valid == 0), check who performed
	   the calculation. It's possible that the checksum was done in
	   software by the network stack earlier (such as Netfilter's
	   CONNTRACK module), and if that says the checksum is bad,
	   we can drop the packet immediately instead of waiting until
	   we try and copy it to userspace. Otherwise, we need to
	   mark the SKB as CHECKSUM_NONE, since the skb->csum field
	   no longer contains the full packet checksum after the
	   call to __skb_checksum_validate_complete().

Fixes: e6afc8ac ("udp: remove headers from UDP packets before queueing")
Fixes: c84d9490 ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NSean Tranchetti <stranche@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      4fb0dc97
    • N
      net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules · b4f003cb
      由 Niklas Cassel 提交于 
      [ Upstream commit 30549aab146ccb1275230c3b4b4bc6b4181fd54e ]

When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.

When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().

Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.

Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.

Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: NNiklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b4f003cb
    • J
      net: sched: gred: pass the right attribute to gred_change_table_def() · 917629e6
      由 Jakub Kicinski 提交于 
      [ Upstream commit 38b4f18d56372e1e21771ab7b0357b853330186c ]

gred_change_table_def() takes a pointer to TCA_GRED_DPS attribute,
and expects it will be able to interpret its contents as
struct tc_gred_sopt.  Pass the correct gred attribute, instead of
TCA_OPTIONS.

This bug meant the table definition could never be changed after
Qdisc was initialized (unless whatever TCA_OPTIONS contained both
passed netlink validation and was a valid struct tc_gred_sopt...).

Old behaviour:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
     gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
     gred setup vqs 4 default 0
RTNETLINK answers: Invalid argument

Now:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
     gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
     gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
     gred setup vqs 4 default 0

Fixes: f62d6b93 ("[PKT_SCHED]: GRED: Use central VQ change procedure")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      917629e6
    • E
      net/mlx5e: fix csum adjustments caused by RXFCS · c5eebcf0
      由 Eric Dumazet 提交于 
      [ Upstream commit d48051c5b8376038c2b287c3b1bd55b8d391d567 ]

As shown by Dmitris, we need to use csum_block_add() instead of csum_add()
when adding the FCS contribution to skb csum.

Before 4.18 (more exactly commit 88078d98 "net: pskb_trim_rcsum()
and CHECKSUM_COMPLETE are friends"), the whole skb csum was thrown away,
so RXFCS changes were ignored.

Then before commit d55bef50 ("net: fix pskb_trim_rcsum_slow() with
odd trim offset") both mlx5 and pskb_trim_rcsum_slow() bugs were canceling
each other.

Now we fixed pskb_trim_rcsum_slow() we need to fix mlx5.

Note that this patch also rewrites mlx5e_get_fcs() to :

- Use skb_header_pointer() instead of reinventing it.
- Use __get_unaligned_cpu32() to avoid possible non aligned accesses
  as Dmitris pointed out.

Fixes: 902a5459 ("net/mlx5e: When RXFCS is set, add FCS data into checksum calculation")
Reported-by: NPaweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Dimitris Michailidis <dmichail@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Paweł Staszewski <pstaszewski@itcare.pl>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Tested-By: NMaria Pasechnik <mariap@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c5eebcf0
    • S
      ipv6/ndisc: Preserve IPv6 control buffer if protocol error handlers are called · dc31623a
      由 Stefano Brivio 提交于 
      [ Upstream commit ee1abcf689353f36d9322231b4320926096bdee0 ]

Commit a61bbcf2 ("[NET]: Store skb->timestamp as offset to a base
timestamp") introduces a neighbour control buffer and zeroes it out in
ndisc_rcv(), as ndisc_recv_ns() uses it.

Commit f2776ff0 ("[IPV6]: Fix address/interface handling in UDP and
DCCP, according to the scoping architecture.") introduces the usage of the
IPv6 control buffer in protocol error handlers (e.g. inet6_iif() in
present-day __udp6_lib_err()).

Now, with commit b94f1c09 ("ipv6: Use icmpv6_notify() to propagate
redirect, instead of rt6_redirect()."), we call protocol error handlers
from ndisc_redirect_rcv(), after the control buffer is already stolen and
some parts are already zeroed out. This implies that inet6_iif() on this
path will always return zero.

This gives unexpected results on UDP socket lookup in __udp6_lib_err(), as
we might actually need to match sockets for a given interface.

Instead of always claiming the control buffer in ndisc_rcv(), do that only
when needed.

Fixes: b94f1c09 ("ipv6: Use icmpv6_notify() to propagate redirect, instead of rt6_redirect().")
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      dc31623a
    • H
      bridge: do not add port to router list when receives query with source 0.0.0.0 · 0f216d94
      由 Hangbin Liu 提交于 
      [ Upstream commit 5a2de63fd1a59c30c02526d427bc014b98adf508 ]

Based on RFC 4541, 2.1.1.  IGMP Forwarding Rules

  The switch supporting IGMP snooping must maintain a list of
  multicast routers and the ports on which they are attached.  This
  list can be constructed in any combination of the following ways:

  a) This list should be built by the snooping switch sending
     Multicast Router Solicitation messages as described in IGMP
     Multicast Router Discovery [MRDISC].  It may also snoop
     Multicast Router Advertisement messages sent by and to other
     nodes.

  b) The arrival port for IGMP Queries (sent by multicast routers)
     where the source address is not 0.0.0.0.

We should not add the port to router list when receives query with source
0.0.0.0.
Reported-by: NYing Xu <yinxu@redhat.com>
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      0f216d94
  3. 22 10月, 2018 8 次提交
  5. 21 10月, 2018 4 次提交
  7. 20 10月, 2018 16 次提交