dmaengine routines can be called from interrupt context and with interrupts
disabled.  Whereas spin_unlock_bh can't be called from such contexts. So this
patch converts all spin_*_bh routines to irqsave variants.

Also, spin_lock() used in tasklet is converted to irqsave variants, as tasklet
can be interrupted, and dma requests from such interruptions may also call
spin_lock.

Now, submission from callbacks are permitted as per dmaengine framework. So we
shouldn't hold any locks while calling callbacks. As locks were taken by parent
routines, so releasing them before calling callbacks doesn't look clean enough.
So, locks are taken inside all routine now, whereever they are required. And
dwc_descriptor_complete is always called without taking locks.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

If len passed in sg for slave_sg transfers is greater than DWC_MAX_COUNT, then
driver programmes controller incorrectly.  This patch adds code to handle this
situation by allocation more than one desc for same sg.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

If transfer status is !=DMA_SUCCESS, return total transfer len as residue,
instead of zero.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

If dmaengine_terminate_all() is called for dma channel, then it doesn't make
much sense to call registered callback routine. While in case of success or
failure it must be called.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

With the addition of the "pause" feature, an active wait was introduced
to check the "FIFO empty" event. This event was not always happening and
a timout contition was needed.
But, in some cases, this event depend on the peripheral connected to the
channel that is paused: FIFO becomes empty if the peripheral consumes data.
The timeout is pretty difficult to evaluate. Moreover, this check is not
needed.
In conclusion, it seems sensible to entirely remove the checking of
"FIFO empty" status when pausing.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
[commit msg edited for grammer]
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Support I2S device for ML7213 IOH
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Currently, Direct-Start mode(*) is enabled.
Our IOH's devices must not use this mode.
This causes unexpected behavior.
This patch deletes Direct-Start setting.
(*) This mode is used in order for CPU to generate the DMA request.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Fix checkpatch warnings.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Currently, even-channel number is set as tx direction and odd is set as rx.
However, though video-in uses ch6, the direction is not tx but rx.
This patch sets video-in's DMA direction correctly.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

A little function helps to chain descriptors:
it is already used in cyclic dma operations, now use it in memcpy and slave_sg
preparation functions.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Pause and resume controls are useful for audio devices. This also returns
correct status from atc_tx_status() in case chan is paused.

Idea from dw_dmac patch by Linus Walleij.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

If transfer status is !=DMA_SUCCESS, return total transfer len as residue,
instead of zero.

Idea from dw_dmac patch by Viresh Kumar.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The compiler nowadays moans about possibly non-assigned variable.
Fix this by default-assigning 0.
Signed-off-by: NPhilippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

DMA controller has two AHB interfaces on the SOC internal
matrix.
It is more efficient to specialize each interface as the
access to memory can introduce latencies that are not compatible
with peripheral accesses requirements.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

There is no need to test if channel is enabled in tasklet:
- in error path, channel is disabled in interrupt routine
- in normal path, this test is performed in sub functions to report
a misuse of the engine.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Now we use Buffer Transfer Completed interrupts. If we
want a chained buffer completed information, we setup the
ATC_IEN bit in CTRLB register in the lli.
This is done by set_desc_eol() function and used by
memcpy/slave_sg functions.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

In the function pdc_desc_get(), var 'i' is not
initialized before use. This patch fixes it.
Signed-off-by: NLiu Yuan <tailai.ly@taobao.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Use the correct api in probe to enable runtime pm for this driver.
Additionally, do not just call legacy suspend for runtime_suspend,
as this duplicates some work the pci core does for you.
Signed-off-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

This patch makes BUG_ON() usage correct in drivers/dma/ppc4xx/adam.c

Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Sean MacLennan <smaclennan@pikatech.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NColy Li <bosong.ly@taobao.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

This patch makes BUG_ON() usage correct in drivers/dma/mv_xor.c

Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NColy Li <bosong.ly@taobao.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

This patch makes BUG_ON() usage correct in drivers/dma/iop-adma.c.

Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: NColy Li <bosong.ly@taobao.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

dwc_scan_descriptors scans all descriptors from active_list in case transfer is
not completed.  It compares first_desc->lli.llp, and then all childrens of its
tx_list. But it doesn't compare its own address, i.e. first_desc->txd.phys, as
this is what we have initially programmed into the controller register. So this
causes dma to stop and finish a transfer, which was never started. And thus
fail.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: NPeter Huewe <huewe.external@infineon.com>
Signed-off-by: NPeter Huewe <huewe.external@infineon.com>
Signed-off-by: NMarcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)".  If that isn't 1, we have way
  deeper problems than a simple multiplication can fix.   - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We check the pointers together but at least one of them could be invalid
due to failed allocation. Since we cannot continue if either of the two
allocations has failed, exit early by freeing them both.

Cc: <stable@kernel.org> # 38.x
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>

These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Converted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

This driver is broken in several aspects.

 1) old style irq_chip functions. Sigh

 2) Abuse of the unlock callback. That's not supposed to be a state
    machine for evrything and some more.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Converted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Convert to the new function names. Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org

This is needed for determining the reason for failure when a softdog
timeout occurs.

We use softdog to watch for critical application failures and at the
minimum a snapshot of the system would help to determine the cause.  In
such a scenario the application could fail but there isn't a softlockup as
such, hence the detect softlockup feature does not help.

The patch adds a module parameter soft_panic which when set to 1 causes
softdog to invoke panic instead of reboot when the softdog timer expires. 
By invoking panic we execute kdump if it is configured and the vmcore
generated by kdump should provide atleast a minimal idea of the reason for
failure.

Based on an original patch by Ken Sugawara <sugaken.r3@gmail.com>
Signed-off-by: NAnithra P J <anithra@linux.vnet.ibm.com>
Reviewed-by: NWANG Cong <xiyou.wangcong@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Fix section mismatch warning:
Mark the called nv_tco_getdevice() as __devinit, just like its caller.

WARNING: drivers/watchdog/nv_tco.o(.devinit.text+0x16): Section mismatch in reference from the function nv_tco_init() to the function .init.text:nv_tco_getdevice()
The function __devinit nv_tco_init() references
a function __init nv_tco_getdevice().
If nv_tco_getdevice is only used by nv_tco_init then
annotate nv_tco_getdevice with a matching annotation.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Stefano found SP5100 TCO watchdog driver using wrong address.

[    9.148536] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[    9.148628] DEBUG __ioremap_caller WARNING address=b8fe00 size=8 valid=1 reserved=1

and e820 said that range is RAM.

We should check if we can use that reading out. BIOS could just program wrong address there.
Reported-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NMike Waychison <mikew@google.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>