The MT devices produce a lot of data. Tell the underlying input device
approximately how many events will be sent per synchronization, to allow
for better buffering. The number is a template based on continuously
reporting details for each finger on a single hand.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The MT devices produce a lot of data. Tell the underlying input device
approximately how many events will be sent per synchronization, to allow
for better buffering. The number is a template based on continuously
reporting details for each finger on a single hand.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Some devices, in particular MT devices, produce a lot of data.  This
may lead to overflowing of the event queues in evdev driver, which
by default are fairly small. Let the drivers hint the average number
of events per packet generated by the device, and use that information
when computing the buffer size evdev should use for the device.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Allocate the event buffer dynamically, and prepare to compute the
buffer size in a separate function. This patch defines the size
computation to be identical to the current code, and does not contain
any logical changes.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Stanse found that tsc is dereferenced earlier than checked for being
NULL in tps6507x_ts_remove. Remove the test because there is no way
for tsc to be NULL there.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This one adds support of a combined irq source for the whole matrix keypad.
This can be useful if all rows and columns of the keypad are e.g. connected
to a GPIO expander, which only has one interrupt line for all events on
every single GPIO.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

If we fail to submit URBs we should take touchpad out of wellsping
mode.
Signed-off-by: NLuo Jinghua <sunmoon1997@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Let's perform be16_to_cpu() conversions once for each received packet,
and then use cached values. Makes code a little bit easier to follow.
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

CONFIG_SPRUCE was removed from kernel around 2.6.26; let's remove the
last remaining piece.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch fixes the follwing warning introduced by commit
067fb2f6 ("Input: ads7846 - return error on
regulator_get() failure"):

drivers/input/touchscreen/ads7846.c: In function 'ads7846_probe':
drivers/input/touchscreen/ads7846.c:1167: warning: format '%ld' expects
type 'long int', but argument 4 has type 'int'
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

1) Use msecs_to_jiffies() instead of calculating by hand.
2) Call cancel_delayed_work_sync() instead of cancel_delayed_work()
   followed by a separate flush_workqueue().
3) Remove the "tsc->wq = 0;"  Sparse complains about that because
   tsc->wq is a pointer, not an int.  It's not needed because we just
   free the pointer anyway.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The S3C touchscreen driver is logging at LOG_INFO on every stylus up
event which spams the console needlessly.  Reduce the priority of the
message to debug level for some peace and quiet.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The name of the Kconfig symbol for the ADC has changed as a result of
application to more SoCs but the select statement has not been updated,
causing linker failures as the ADC core has not been built.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Fix a bunch of new rapidio kernel-doc warnings:

Warning(include/linux/rio.h:123): No description found for parameter 'comp_tag'
Warning(include/linux/rio.h:123): No description found for parameter 'phys_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'em_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'pwcback'
Warning(include/linux/rio.h:247): No description found for parameter 'set_domain'
Warning(include/linux/rio.h:247): No description found for parameter 'get_domain'
Warning(drivers/rapidio/rio-scan.c:1133): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio-scan.c:1133): Excess function parameter 'port' description in 'rio_init_em'
Warning(drivers/rapidio/rio.c:349): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio.c:349): Excess function parameter 'mport' description in 'rio_request_inb_pwrite'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'port'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'local'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'destid'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'hopcount'
Warning(drivers/rapidio/rio.c:393): Excess function parameter 'rdev' description in 'rio_mport_get_physefb'
Warning(drivers/rapidio/rio.c:845): Excess function parameter 'local' description in 'rio_std_route_clr_table'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

airlied -> brown paper bag.

I blame Hi-5 or the Wiggles for lowering my IQ, move the fix inside some
brackets instead of breaking everything in site.

Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

acpi pad driver kind of aggressively marks TSC as unstable at init
time, on mwait capable and non X86_FEATURE_NONSTOP_TSC systems. This is
irrespective of whether pad driver is ever going to be used on the
system or deep C-states are supported/used. This will affect every user
who just happens to compile in (or get a kernel version which
compiles in) acpi pad driver.

Move mark_tsc_unstable() out of init to the actual idle invocation path
of the pad driver.

There is also another bug/missing_feature in the code that it does not
support 'always running apic timer' and switches to broadcast mode
unconditionally. Shaohua, can you take a look at that please.
Signed-off-by: NVenkatesh Pallipadi <venki@google.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

drivers/acpi/sleep.h:3: WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

acpi_enter_[simple,bm] does
idle timing in ns, convert it to timeval, then to us, then to
pmtimer_ticks and then back to ns.

This patch changes things to
idle timing in ns, convert it to us, and then to pmtimer_ticks.

Just saves an imul along this path, but makes the code cleaner.
Signed-off-by: NVenkatesh Pallipadi <venki@google.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This EXPERIMENTAL driver supersedes acpi_idle on
Intel Atom Processors, Intel Core i3/i5/i7 Processors
and associated Intel Xeon processors.

It does not support the Intel Core2 processor or earlier.

For kernels configured with ACPI, CONFIG_INTEL_IDLE=y
allows intel_idle to probe before the ACPI processor driver.
Booting with "intel_idle.max_cstate=0" disables intel_idle
and the system will fall back on ACPI's "acpi_idle".

Typical Linux distributions load ACPI processor module early,
making CONFIG_INTEL_IDLE=m not easily useful on ACPI platforms.

intel_idle probes all processors at module_init time.
Processors that are hot-added later will be limited
to using C1 in idle.
Signed-off-by: NLen Brown <len.brown@intel.com>

commit d306ebc2
(ACPI: Be in TS_POLLING state during mwait based C-state entry)
fixed an important power & performance issue where ACPI c2 and c3 C-states
were clearing TS_POLLING even when using MWAIT (ACPI_STATE_FFH).
That bug had been causing us to receive redundant scheduling interrups
when we had already been woken up by MONITOR/MWAIT.

Following up on that...

In the MWAIT case, we don't have to subsequently
check need_resched(), as that c heck was there
for the TS_POLLING-clearing case.

Note that not only does the cpuidle calling function
already check need_resched() before calling us, the
low-level entry into monitor/mwait calls it twice --
guaranteeing that a write to the trigger address
can not go un-noticed.

Also, in this case, we don't have to set TS_POLLING
when we wake, because we never cleared it.
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NVenkatesh Pallipadi <venki@google.com>

BugLink: http://bugs.launchpad.net/bugs/559065

In fec open/close function, we need to use phy_connect and phy_disconnect
operation before we start/stop phy. Otherwise it will cause system hang.

Only call fec_enet_mii_probe() in open function, because the first open
action will cause NULL pointer error.
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the structure to avoid the following warning:

WARNING: drivers/serial/built-in.o(.data+0x534): Section mismatch in reference from the variable s5p_serial_drv to the function .devexit.text:s3c24xx_serial_remove()
The variable s5p_serial_drv references
the function __devexit s3c24xx_serial_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We need to zero context memory on 5709 in the function cnic_init_context().
Without this, iscsid restart on 5709 will not work because of stale data.
TX context blocks should not be initialized by cnic_init_context() because
of the special remapping on 5709.

Update version to 2.1.2.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the point of the print, dev is NULL.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@

if ((E == NULL && ...) || ...)
{
  ... when != if (...) S1 else S2
      when != E = E1
* E->f
  ... when any
  return ...;
}
else S3
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the point of the print, dev is NULL.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@

if ((E == NULL && ...) || ...)
{
  ... when != if (...) S1 else S2
      when != E = E1
* E->f
  ... when any
  return ...;
}
else S3
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a compile issue when openfirmware is enabled from commit
2146325d.
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Soekris net5501 is x86 only and cleanup some undeeded dependencies
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

api_pad exclusively uses MONITOR/MWAIT to sleep in idle,
so it does not need the wakeup IPI during idle sleep
that is provoked by clearing TS_POLLING.
Signed-off-by: NLen Brown <len.brown@intel.com>
Cc: Shaohua Li <shaohua.li@intel.com>

The ACPI driver would fail probe when it found that
another driver had previously registered with cpuidle.

But this is a natural situation, as a native hardware
cpuidle driver should be able to bind instead of ACPI,
and the ACPI processor driver should be able to handle
yielding control of C-states while still handling
P-states and T-states.

Add a KERN_DEBUG line showing when acpi_idle
does successfully register.
Signed-off-by: NLen Brown <len.brown@intel.com>

cpuidle_register_driver() sets cpuidle_curr_driver
cpuidle_unregister_driver() clears cpuidle_curr_driver

We should't expose cpuidle_curr_driver to
potential modification except via these interfaces.
So make it static and create cpuidle_get_driver() to observe it.
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix the names of twl5031 specific sih modules to match
the documentation.
Signed-off-by: NIlkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Unlike real i2c-devices which get detached from the driver, dummy-devices
get truly unregistered. So, there has never been a need to clear the
clientdata because the device will go away anyhow. For the occasions fixed
here, clearing clientdata was even dangerous as the structure was freed
already.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add a new driver to support the AB8500 Power Management chip, replacing
the current AB4500.  The new driver replaces the old one, instead of an
incremental modification, because this is a substantial overhaul
including:

 - Split of the driver into -core and -spi portions, to allow another
   interface layer to be added

 - Addition of interrupt support

 - Switch to MFD core API for handling subdevices

 - Simplification of the APIs to remove a redundant block parameter

 - Rename of the APIs and macros from ab4500_* to ab8500_*

 - Rename of the files from ab4500* to ab8500*

 - Change of the driver name from ab4500 to ab8500
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

rdc_gpio_set_value_impl has the gpio data registers 1 and 2 inverted, fix this.
Signed-off-by: NBernhard Loos <bernhardloos@gmail.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The rdc321x southbridge PCI device has no MEM PCI resources that we could
pass to mfd_add_devices. Since 33254dd5, mfd_add_device checks for the
mem_base argument that we set to NULL. Changing the resources passed to
our MFD cells from IORESOURCE_MEM to IORESOURCE_IO fixes that. Since we use
those resources as offsets to the PCI configuration space base address of
the southbridge device this is also more adequate.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This reduces code clutter a bit and will ease an migration to genirq.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>