Adds support to VC211A em2800 card. As this board doesn't have eeprom,
and uses a common set of i2c address, it has no way to add any
autodetection for it.

The patch were tested by me and by Raimundo on his board. Thanks to
those tests, several bugs related to em2800 support were corrected.

for producing the usbsnoop dump, used to get the gpio's and allowing me
to remotelly access his machine and to the needed tests.

Thanks-to: Raimundo Eduvirgnes de Oliveira <eduvirgens@yahoo.com.br>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since em2800 can't support 720x480 / 720x576, the driver used to reduce
the scale to half the size on those chips. As the proper fix were
applied, reducing the maximum horizontal resolution to 640, this hack
can be removed.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With em2800 hardware, AC97 hardware can be detected even when it doesn't
exist. If, after probing for AC97, the driver won't find a companion
chip, simply prevents the load of the audio modules.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Due to hardware limitation, em2800 chips can't work at resolutions
higher than 640x576, since the URB packet size is not enough.

The effect is that the image looses packages and shows a distortion
along the vertical axes.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It seems that some patch broke alt modprobe parameter. Fix it to allow
changing alternate interfaces during module load and at runtime.

If changed during runtime, you'll need to stop a and restart stream for
the parameter to be used.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert printks to em28xx_err and em28xx_info
Signed-off-by: NFilipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert printks to em28xx_err.
Signed-off-by: NFilipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Upcoming I2C v4l2_subdev drivers need a way to control the subdevice
power state from the core. This use case is already partially covered by
the tuner s_standby operation, but no way to explicitly come back from
the standby state is available.

Rename the tuner s_standby operation to core s_power, and fix tuner
drivers accordingly. The tuner core will call s_power(0) instead of
s_standby(). No explicit call to s_power(1) is required for tuners as
they are supposed to wake up from standby automatically.

[mchehab@redhat.com: CodingStyle fix]
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Recent fixes to the em28xx and saa7134 drivers have been overzealous.
While the ir-kbd-i2c platform data indeed needs to be persistent, the
struct i2c_board_info doesn't, as it is only used by i2c_new_device().

So revert a part of the original fixes, to save some memory.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The board support has been validated by the user, so get rid of the warning
that shows up on board load.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid
XS (em2882).

Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing
and testing pretty much the exact same patch as provided by Uros.  Between
the two of them, they got all the core functionality working for the device.

Cc: Andrej Suligoi <suligoi@gmail.com>
Signed-off-by: NUroš Vampl <mobile.leecher@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Seems that the reference design used for the KWorld 2800d switched from the
em2860 to em2862, so we need to add the new USB id (and the i2c hash remains
so all we need is the default em2862 id.

Thanks to Ian Young for reporting the issue and testing the fix.

Cc: Ian Young <ian@duffrecords.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Set device GPIOs only once. There is no need for .dvb_gpio to select
between analog and digital because device is digital only.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Because the counters were not reset when starting up streaming, they would
be reused from the previous run.  This can result in cases such that when the
second instance of streaming starts up, the "cnt" variable in
em28xx_audio_isocirq() can end up being negative, resulting in attempting to
write to memory before the start of runtime->dma_area (as well as having a
negative number of bytes to copy).
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.

This simplifies this API substantially.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Support for Reddo DVB-C USB TV Box device. Remote is not working yet.
Thanks to Benjamin Larsson <banan@ludd.ltu.se>

Cc: Benjamin Larsson <banan@ludd.ltu.se>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove some emacs tags from em28xx-vbi.c, which were copied from cx88-vbi.c,
per Mauro Carvalho Chehab's request.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix some codingstyle issues introduced during the addition of em28xx VBI
support.  The patch makes no functional changes other than converting a few
debug printk() statements to em28xx_isocdbg.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix a few codingstyle issues introduced when I was adding the VBI support to
the em28xx driver.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove unused variable from when I introduced the g_std() function.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove redundant call to set the vinctrl register.  This eliminates any
ambiguity as to how the register is configured (since it is now always set in
em28xx_set_outfmt).

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We need to implement the g_std call, or else the default norm always gets
returned, which breaks VBI capturing if you had changed the standard to NTSC
using s_std.

I had temporarily changed the default norm to NTSC so that zvbi-ntsc-cc
wouldn't choke, so now that we are returning the correct value, switch it back
to PAL as the default.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change the code so we only claim to support VBI if the underlying chipset
actually has the support.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do not create the VBI device in cases where VBI is not supported on the target
em28xx chip.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove an unreferenced variable introduced during the VBI introduction.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current locking infrastructure didn't support having multiple fds accessing
the device (such as video and vbi).  Rework the locking infrastructure,
borrowing the design from cx88.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When adding support for both video and VBI, I missed the mmap ioctl.  Add
the missing call.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for raw VBI capture for the em28xx bridge, currently only for
NTSC.  Support for PAL capture to follow shortly (including the removal of
numerous hard-coded NTSC-specific sizes for capture buffers, etc).

Note that the code currently changes the default current norm from PAL to
NTSC (so that zvbi-ntsc-cc works properly).  The default norm really should
be moved into a board-level parameter.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add code enabling the VBI registers for variants of the em28xx chip that
support VBI, and make sure the isoc streaming code continues to work for
the video component of the stream (note the video and vbi data arrive
intermixed on the same isoc pipe).

Note that this version just drops the actual VBI data onto the floor as
opposed to processing it.  The "#ifdef 0" tags are for the videobuf code that
appears in the next patch in this series.

We created a separate version of the isoc_copy version for parsing the version
of the stream that includes VBI data.  In theory, they might be able to be
merged at some point in the future, but the initial goal is to ensure that we
do not cause any regressions with devices that do not have VBI support.

This work was sponsored by EyeMagnet Limited.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Properly document the video input control register, in preparation for the
addition of VBI support.  Note this patch makes no functional changes.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added Kworld DVD Maker 2
Thanks to C Western <l@c-m-w.me.uk> for reporting this board.
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are some extra parenthesis at the clauses, and some switch() tests
for boards that don't have i2c ir. Remove those extra code.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently, the logic to load ir i2c ancillary module is broken. It is
associated to Hauppauge devices with IR flag on their eeprom, no matter
if the device uses i2c or em28xx direct IR support. That's wrong.

Instead, add a flag to the boards that use i2c IR chips and load the
module only for those devices and if ir is not disabled.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.

Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.

Before this patch, if ir-kbd-i2c were probed after em28xx, trash data
were used. After the patch, no matter what order, it is properly
reported as tested by me:

input: i2c IR (i2c IR (EM2840 Hauppaug as /class/input/input10
ir-kbd-i2c: i2c IR (i2c IR (EM2840 Hauppaug detected at i2c-4/4-0030/ir0 [em28xx #0]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:

1) It requires that the scancode to be at the range 00-7f;

2) keycodes should be masked on 7 bits in order for it to work;

3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;

4) it is different than what is done with dvb-usb approach;

5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.

This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
       u16     scancode;
       u32     keycode;
};

This is very close to what dvb does. So, a further integration with DVB
code will be easy.

While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.

The only notable effect is the redution of about 35% of the ir-common
module size:

   text    data     bss     dec     hex filename
   6721   29208       4   35933    8c5d old/ir-common.ko
   5756   18040       4   23800    5cf8 new/ir-common.ko

In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.

This patch itself shouldn't be doing any functional changes.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: NShine Liu <shinel@foxmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for the remote control that comes with the Cinergy Hybrid T USB XS

Thanks to Jelle de Jong for providing sample hardware to test with.

Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixed eeprom hash table
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>