Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RSSI reported by the RX descriptor requires little manipulation.
Manipulate and report the correct RSSI to the stack. This will
fix the improper signal levels reported by iwconfig iw dev wlanX
station dump. Also the Link Quality reported seems to be varying
(falls to zero also sometimes) when iperf is run from STA to AP.

Also use the default noise floor for now as the one reported
during the caliberation seems to be wrong.

The Signal and Link Quality before this patch (taken while TX is
in progress from STA to AP)

09:59:13.285428037 Link Quality=29/70  Signal level=-81 dBm
09:59:13.410660084 Link Quality=20/70  Signal level=-90 dBm
09:59:13.586864392 Link Quality=21/70  Signal level=-89 dBm
09:59:13.710296281 Link Quality=21/70  Signal level=-89 dBm
09:59:13.821683064 Link Quality=25/70  Signal level=-85 dBm
09:59:13.933402989 Link Quality=24/70  Signal level=-86 dBm
09:59:14.045839276 Link Quality=26/70  Signal level=-84 dBm
09:59:14.193926673 Link Quality=23/70  Signal level=-87 dBm
09:59:14.306230262 Link Quality=31/70  Signal level=-79 dBm
09:59:14.419459667 Link Quality=26/70  Signal level=-84 dBm
09:59:14.530711167 Link Quality=37/70  Signal level=-73 dBm
09:59:14.642593962 Link Quality=29/70  Signal level=-81 dBm
09:59:14.754361169 Link Quality=21/70  Signal level=-89 dBm
09:59:14.866217355 Link Quality=21/70  Signal level=-89 dBm
09:59:14.976963623 Link Quality=28/70  Signal level=-82 dBm
09:59:15.089149809 Link Quality=26/70  Signal level=-84 dBm
09:59:15.205039887 Link Quality=27/70  Signal level=-83 dBm
09:59:15.316368003 Link Quality=23/70  Signal level=-87 dBm
09:59:15.427684036 Link Quality=36/70  Signal level=-74 dBm
09:59:15.539756380 Link Quality=21/70  Signal level=-89 dBm
09:59:15.650549093 Link Quality=22/70  Signal level=-88 dBm
09:59:15.761171672 Link Quality=32/70  Signal level=-78 dBm
09:59:15.872793750 Link Quality=23/70  Signal level=-87 dBm
09:59:15.984421694 Link Quality=22/70  Signal level=-88 dBm
09:59:16.097315093 Link Quality=21/70  Signal level=-89 dBm

The link quality and signal level after this patch (take while
TX is in progress from STA to AP)

17:21:25.627848091 Link Quality=65/70  Signal level=-45 dBm
17:21:25.762805607 Link Quality=65/70  Signal level=-45 dBm
17:21:25.875521888 Link Quality=66/70  Signal level=-44 dBm
17:21:25.987468448 Link Quality=66/70  Signal level=-44 dBm
17:21:26.100628151 Link Quality=66/70  Signal level=-44 dBm
17:21:26.213129671 Link Quality=66/70  Signal level=-44 dBm
17:21:26.324923070 Link Quality=65/70  Signal level=-45 dBm
17:21:26.436831357 Link Quality=65/70  Signal level=-45 dBm
17:21:26.610356973 Link Quality=65/70  Signal level=-45 dBm
17:21:26.723340047 Link Quality=65/70  Signal level=-45 dBm
17:21:26.835715293 Link Quality=64/70  Signal level=-46 dBm
17:21:26.949542748 Link Quality=64/70  Signal level=-46 dBm
17:21:27.062261613 Link Quality=65/70  Signal level=-45 dBm
17:21:27.174511563 Link Quality=64/70  Signal level=-46 dBm
17:21:27.287616232 Link Quality=64/70  Signal level=-46 dBm
17:21:27.400598119 Link Quality=64/70  Signal level=-46 dBm
17:21:27.511381404 Link Quality=64/70  Signal level=-46 dBm
17:21:27.624530421 Link Quality=65/70  Signal level=-45 dBm
17:21:27.737807109 Link Quality=64/70  Signal level=-46 dBm
17:21:27.850861352 Link Quality=65/70  Signal level=-45 dBm
17:21:27.963369436 Link Quality=64/70  Signal level=-46 dBm
17:21:28.076582289 Link Quality=64/70  Signal level=-46 dBm
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The AR_SREV_9285_1[12]_OR_LATER macros already contains the
AR_SREV_9285 check.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is already handled properly in ath9k_hw_getnf.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug in ath9k_hw_init_cal() where the wrong
calibration was being done for non-AR9285 chipsets.
Also add a few helpful comments.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces old 'hal_' prefixes with 'ath9k_'.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up the functions dealing with calibration,
using proper return values.
ath9k_hw_per_calibration(), ath9k_hw_calibrate now return bool values
instead of setting error values in the function arguments.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ADC gain calibration has to be done for all non 2GHZ-HT20 channels.
Regression from "ath9k: use ieee80211_conf on ath9k_hw_iscal_supported()"

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The operating HT mode is stored in chanmode and
not channelFlags.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

How time flies.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the sparse complaints:

drivers/net/wireless/ath9k/eeprom.c:1407:5: warning: symbol
'ath9k_hw_4k_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1436:19: warning: symbol
'eep_4k_ops' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2808:5: warning: symbol
'ath9k_hw_def_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2837:19: warning: symbol
'eep_def_ops' was not declared. Should it be static?
  CC [M]  drivers/net/wireless/ath9k/eeprom.o
  CHECK   drivers/net/wireless/ath9k/mac.c
  CC [M]  drivers/net/wireless/ath9k/mac.o
  CHECK   drivers/net/wireless/ath9k/calib.c
drivers/net/wireless/ath9k/calib.c:883:6: warning: symbol 'ar9285_clc'
was not declared. Should it be static?
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates the initvalues for AR9285 chipset and also adds
periodic PA offset caliberation.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

OLC_FOR_AR9280_20_LATER is defined in multiple places,
move it to a common location.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX and calibration have different timeout requirements.
This patch fixes it by changing the HW wait routine
to accept a timeout value.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds Open Loop Control support for Atheros chipsets that
supports open loop power control.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the various function pointer
assignments and unifies them in a single ops structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Finally, merge these structures and have a single
HW specific data structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split the core header files into manageable pieces.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix AR9285 specific noise floor reads and initialize tx and rx
chainmask during reset. This along with the following earlier
patches of ath9k fixes an issue with association noticed in
noisy environment.

ath9k: Fix typo in chip version check
ath9k: Remove unnecessary gpio configuration in ath9k_hw_reset()
ath9k: Fix bug in NF calibration
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The number of chainmasks for AR9285 weren't being
setup when running NF calibration.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that cfg80211 has its own regulatory infrastructure we can
condense ath9k's regulatory code considerably. We only keep data
we need to provide our own regulatory_hint(), reg_notifier() and
information necessary for calibration.

Atheros hardware supports 12 world regulatory domains, since these
are custom we apply them through the the new wiphy_apply_custom_regulatory().
Although we have 12 we can consolidate these into 5 structures based on
frequency and apply a different set of flags that differentiate them on
a case by case basis through the reg_notifier().

If CRDA is not found our own custom world regulatory domain is applied,
this is identical to cfg80211's except we enable passive scan on most
frequencies.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The NOISE_FLOOR array we have is mode specific, and the only
possible indexed values are A, B and G. The mode routine only
can return G or A, so this is band specific. Then since the
values for A and G (5ghz or 2ghz) are the same (-96) we simply
remove the array and use a static value.

If we later determine we want to use special values for
HT configurations we can use the new mac80211 conf_is_ht*()
helpers.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_iscal_supported() just needs to be aware of your band
and if HT20 is being used so lets abandon our internal channel,
HT appended values and internal mode values and use ieee80211_conf
which already carries this information. This works as calibration
is being done for the currently configured channel.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Lets make the request to get the current noise floor threshold
from the EEPROM band specific as it is band specific, not mode
specific.

This also adds a backpointer on the private channel structure
back to the ieee80211_channel structure as this is now needed during
ath9k_hw_getnf().
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove all the useless __func__ prefixes in debug messages,
and replace the DPRINTF macro with a function.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes incorrect noise floor threshold values.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split hw.c into more manageable files:
   ani.c
   calib.c
   eeprom.c
   mac.c
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>