FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In loose BT Coex scheme, the aggregation size doesn't need to
be limited.

To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In RF KILL the init ucode is running, but don't complete
all its tasks, so we need to run the init ucode again.
Change the flag name to init_ucode_complete, to be more appropriate.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is the new API for BT Coex. The full functionality
will be implemented in further patches.

Note: this disables BT Coex for the currently existing
fw (-7 version).

There is also a new command - the channel inhibition command.

This command tells BT what channels to avoid in order to
minimise the interaction between BT and WiFi.
We can tell BT about 2 channels, primary and secondary.
BT will not tune to primary at all and will avoid secondary
as much as possible.

This also means that we need to track vifs that AP / GO.
So rename iwl_mvm_bt_coex_vif_assoc to
iwl_mvm_bt_coex_vif_change to better reflect its real
meaning.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for scheduled scan according to firmware support.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use beacon statistics notification handler
to notify bt coex about rssi changes.
Mac80211's mechanism is not used anymore.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add an option to set rx antennas for the scan command from debugfs.
Create a file called ant_rxchain in the mvm debugfs directory.
To choose antennas, write a number between 1-7 to ant_rxchain.
Write 1 for A, 2 for B, 3 for AB and so on.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For testing, implement setting continuous NoA duration
using a new MVM-specific testmode command.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The Performance Based Window snooze mechanism is based on uAPSD and is
used in low-medium traffic scenarios, in order to provide better power
performance while insuring low latency and jitter for the incoming traffic.
This patch enables PBW snoozing in case uAPSD is enabled and all ACs are
uAPSD trigger and delivery enabled.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use beacon statistics notification to track RSSI.
Notify mac80211 when the tresholds are crossed.
The roaming treshold is configured to be
equal to cqm_thold. If the beacon filtering command
is not supported by fw fall back and use mac80211
mechanism.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement basic uAPSD client support adding the following:

- Advertise uAPSD support in HW capabilities
- Set all ACs trigger- and delivery-enabled
- Set max SP length to 2 buffered frames
- Assign QNDP with the highest TID with no mandatory admission
  control required
- Set uAPSD related parameters in Power Table command
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a debugfs entry for the RX statistics received from
the firmware.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If fw_restart is disabled, using the fw_restart debugfs
file will enable fw_restart and then send the failing
command, but this still frequently fails restart because
it resets fw_restart afterwards and is thus racy.

Fix this by tracking fw_restart separately and allowing
"always restart", "never restart" and "restart N times".
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change beacon filtering command due to a change in the API.

In case the FW supports the old API, we do not send the
BF HCMD and assume that since the corresponding struct in
the FW is zeroed by default then we don't need to disable
it in the FW actively.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Signed-off-by: NDor Shaish <dor.shaish@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To make maintaining some constant default values in the
driver easier, declare them in a separate file.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Newer firmware supports offloading more IPv6 addresses for NDP,
adjust the code to send the correct command depending on the
firmware capability.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change power management implementation to support new host-device API
containing uAPSD parameters. Verify FW support for this new API.
Use the new power table command (0xA9) to configure power management.
Use the legacy command (0x77) if FW does not support the new API.
New file power_legacy.c is introduced for legacy implementation.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firmware / HW can't support more than 16 Rx BA sessions.
Deny any attemps to open more sessions than that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

Add sram dump on NIC error for debug improvement.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To improve power consumption in idle associated mode FW may lower
RX power. This low linearity mode is acceptable for listening low rate
RX such as beacons and groupcast. The driver enables LPRX only if PM
is enabled and associated AP's beacon TX rate is 1Mbps or 6Mbps.
LPRX RSSI threshold is used to limit a range where LPRX is applied.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add prints visible to the user when entering and exiting
thrermal throttling, because so users can tell that the
NIC is getting too hot (and throughput will decrease.)
Signed-off-by: Neytan lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The old nl80211 testmode is no longer useful in iwlwifi,
we're moving towards a new model internally and there's
no open tool to use it, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the D3 firmware crashes, it can be helpful for debugging to
resume the system to get the SRAM snapshot to see why it crashed.
Allow enabling this with a debugfs option.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This function doesn't actually exist, remove its declaration.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The AP mode needs to use the MCAST fifo for the MCAST
frames sent after the DTIM. This fifo needs to be
configured with the same parameters as the VOICE FIFO.

A separate SCD queue is mapped to this fifo - the cab_queue
(cab stands for Content After Beacon). This queue isn't
connected to any station, but rather to the MAC context.
This queue should (and is already) be set as the MCAST
queue - this is part of the of MAC context command.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.

Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.

Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)

Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.

Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add debugfs files to control powersave parameters for testing.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firmware supports periodic keep alive and beacon monitoring,
so advertise connection monitor offload capability by setting
IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons
notification handler. Call ieee80211_beacon_loss in case of
missed beacons, so AP probing by mac80211 can be triggered.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to avoid NIC destruction due to high temperature,
CT kill will power down the NIC.

To avoid this, thermal throttling will decrease throughput
to prevent the NIC from reaching the temperature at which
CT kill is performed.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Beacon abort is used by device to increase idle dwell time when system
is idle. This algorithm is on top of beacon filtering feature. Enable
beacon abort only if power management is enabled.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.

Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.

Cc: stable@vger.kernel.org [3.9]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The D3 image SRAM is overwritten by the runtime image, so
it can't be accessed after resume. However, it can be very
useful to look at it to know what happened during D3, so
add the ability to store the image and make it available
in debugfs.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In current implementation, the phy context is tightly coupled
with the channel context. This complicates the possibility of
using the same phy context for both netdev interfaces and the P2P
Device interface. To loosen this coupling:

1. Manage all the phy contexts in the mvm op mode, and only save
   the phy context id in the chanctx memory.
2. Reference count the phy contexts and free them only when they
   are not longer used (both by mac80211 and P2P Device).
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add iwl_beacon_filter_cmd struct, disable and enable beacon
filtering as needed.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function just wraps an existing one, remove it.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>