FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This should really not happen. If it does, restarting is the
only way to recover since the driver and the firmware might
very well be out of sync. Moreover, iwl_op_mode_nic_error
will print data that might help debugging.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Single shared antenna devices need a special LUT.
Address this need.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In loose BT Coex scheme, the aggregation size doesn't need to
be limited.

To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In RF KILL the init ucode is running, but don't complete
all its tasks, so we need to run the init ucode again.
Change the flag name to init_ucode_complete, to be more appropriate.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firmware API for IPv6 NDP/NS offload has changed again.
Implement support for the new API; this requires calculating
the solicited node address for each "target" address as it's
no longer ignored by the firmware.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rssi events were enabled on interfaces using 5.2GHz.
Interfaces on 5.2GHz were taken into account while
determining the ACK / CTS kill mask. Fix that.

The last rssi notified to BT Coex was reset every BT Coex
Notification. Since we get a lot of these notifications
from the firmware, we reset the rssi all the time which
means that the bt_rssi_event is called all the time.
Fix that by puting the rssi we pull upon BT Coex
notification into iwl_mvm_vif_bf_data.last_bt_coex_event
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we have only one antenna for BT and WiFi, reduced Tx
power is irrelevant.
Also, in loose scheme, we should not use reduced Tx power
nor set the control mask to Tx power.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some debugfs write() operations of the MVM Firmware will ignore the
count argument, and will copy more bytes than what was specified.
Fix this by getting the right count of bytes.

This will honor restrictions put on the number of bytes to write and
avoid strcmp() calls on garbage data.
Signed-off-by: NDjalal Harouni <tixxdz@opendz.org>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mvm doesn't support HT GF so drop all relevant code in rs.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The data in MailBox comes direclty from the BT core.
We should use the data processed by the WiFi fw that is
appended to the MailBox in the BT Coex notification.
Also decide on whether the Coex type based on the input
from the the firmware and not hard coded.

Also fix the SMPS SISO threshold to 2 (it was 3).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This was due to a fw remainder of old implementation.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is the new API for BT Coex. The full functionality
will be implemented in further patches.

Note: this disables BT Coex for the currently existing
fw (-7 version).

There is also a new command - the channel inhibition command.

This command tells BT what channels to avoid in order to
minimise the interaction between BT and WiFi.
We can tell BT about 2 channels, primary and secondary.
BT will not tune to primary at all and will avoid secondary
as much as possible.

This also means that we need to track vifs that AP / GO.
So rename iwl_mvm_bt_coex_vif_assoc to
iwl_mvm_bt_coex_vif_change to better reflect its real
meaning.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for scheduled scan according to firmware support.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

New FW doesn't use the SSID from scan request template. Adding
a TLV flag to indicate the change, and fixing the flows to send
the first SSID in SSID list if the flag is on.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We want to dump the SRAM when we have an error interrupt
from the device. This happens in non-sleepable context,
hence the change.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

VHT introduces MCS8 and MCS9. Update the expected tpt tables
to include these. Previous expected values for 20/40 MHz
are incorrect in certain cases so fix these as well.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Tested-by: NEfi Tubul <efi.tubul@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current code didn't handle well the case where we're in SISO using
ANT B and there's a BT load. Switch to ANT A in this case.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Newer firmware don't clean the RFKILL interrupt in APMG, do
it in driver instead.
If we forget to do so, we can't send HCMD to firmware while
the NIC is in RFKILL state.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for new station management firmware API. The old
ADD_MODIFY_STA command has been replaced with two: a modified
ADD_MODIFY_STA and a new ADD_MODIFY_STA_KEY command.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Adjust the following:

- RX/TX AP-to-PSM timeout in case of uAPSD and PBW snoozing
- PSM-to-AM TX/RX heavy traffic thresholds
- Beacon abort escape timer for D3/D0i3
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will deadlock due to commit 9f34783863bea806
("iwlwifi: mvm: Implement BT coex notifications"):

  =============================================
  [ INFO: possible recursive locking detected ]
  3.5.0 #10 Tainted: G        W  O
  ---------------------------------------------
  kworker/2:1/5214 is trying to acquire lock:
   (&mvm->mutex){+.+.+.}, at: [<ffffffffa03be23e>] iwl_mvm_bt_rssi_event+0x5e/0x210 [iwlmvm]

  but task is already holding lock:
   (&mvm->mutex){+.+.+.}, at: [<ffffffffa03ab2d9>] iwl_mvm_async_handlers_wk+0x49/0x120 [iwlmvm]

  other info that might help us debug this:
   Possible unsafe locking scenario:

         CPU0
         ----
    lock(&mvm->mutex);
    lock(&mvm->mutex);

   *** DEADLOCK ***

Change-Id: I9104f252b34676e2f7ffcd51166f95367e08a4d9
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/21887Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Conflicts:
	drivers/net/wireless/iwlwifi/mvm/bt-coex.c

Use beacon statistics notification handler
to notify bt coex about rssi changes.
Mac80211's mechanism is not used anymore.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When firmware restart happens, the timers are obviously reset and
the new firmware has no synchronisation with the AP as we program
timings to the pre-restart values. The firmware should attempt to
synchronise by itself, but in multi-channel scenarios this isn't
easy, particularly since it has to try to keep service quality up
for other MACs.

To make it more reliable, give each client MAC some time to catch
beacons when restarting or resuming. Service quality was impacted
anyway (or in resume doesn't really matter much.)
Reviewed-by: NMoshe Island <moshe.island@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The XXX_SWITCH_ANTENNA1/2 actions keep track of switching between
3 single antennas or between 3 pairs in case of MIMO2 on a MIMO3 device.
As current and future chips will have at most 2 antennas drop these.
While at it also convert the actions into enums and cleanup
the code a bit.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Newer firmware fixed a bug that prevented to use CTS to
self. Firmwares with API greater than 8 have this bug
fixed. Enable the feature for these firmwares only.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add an option to set rx antennas for the scan command from debugfs.
Create a file called ant_rxchain in the mvm debugfs directory.
To choose antennas, write a number between 1-7 to ant_rxchain.
Write 1 for A, 2 for B, 3 for AB and so on.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of keeping track of the non-QoS seqno for each station,
query the firmware when suspending, that's more efficient. As
this can fail, move the station ID mangling later in the code.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a testmode command to (manually) disable (and re-enable)
beacon filtering for testing purposes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For testing, implement setting continuous NoA duration
using a new MVM-specific testmode command.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adding the device list from the Windows driver description files
included with a new Qualcomm MDM9615 based device, "Alcatel-sbell
ASB TL131 TDD LTE", from China Mobile.  This device is tested
and verified to work.  The others are assumed to work based on
using the same Windows driver.

Many of these devices support multiple QMI/wwan ports, requiring
multiple interface matching entries.  All devices are composite,
providing a mix of one or more serial, storage or Android Debug
Brigde functions in addition to the wwan function.

This device list included an update of one previously known device,
which was incorrectly assumed to have a Gobi 2K layout.  This is
corrected.
Reported-by: N王康 <scateu@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "id" variable was being incremented in common code, but only
initialized and used in IPv4 code.  We move the increment to the IPv4
code too, and then legitimately use the uninitialized_var() macro to
avoid the gcc 4.6 warning that 'id' may be used uninitialized.
Note that gcc 4.7 does not warn.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>