RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in
no link mode, otherwise it'll not be able to associate when this flag is
not set after the change "mac80211: fix managed mode BSSID handling".

By accident, setting BSSID of AP before association makes 8187B to
successfuly associate even when ENEDCA flag isn't set, which was the
case before the mac80211 change. But now the BSSID of AP we are trying
to associate is only available after association is successful, and
any attempt to associate without the needed flag doesn't work.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

http://bugzilla.kernel.org/show_bug.cgi?id=13383Reported-by: NPrzemyslaw Kulczycki <azrael@autocom.pl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

First of all, it exposes the SKB list implementation.

Second of all it's not needed.  If we get called here, we
successfully enqueued the URB with the linked SKB and
such a completion only gets called one time on such an
SKB.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The following patch implements some control over the LED on RTL8187B and
RTL8187L devices. Triggers are registered for TX and RX. Whenever the
trigger event occurs, the LED is turned off for 1/20 second, then turned
back on.

Note: For those RTL8187X devices that are built into the computer and have
a LED that is expected to be controlled with a radio switch, this patch will
not operate that LED. That will take a separate patch to be prepared later.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This message appears to be nothing more than a leftover of the
experimental-8187B era. Also, we print the HW type in the hwaddr line,
making this message reduntant. And it's definitely not important
enough to be a KERN_WARNING.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new USB ID codes. These come from two postings on forums and
mailing lists, and four are derived from the .inf that accompanies
the latest Realtek Windows driver for the RTL8187L.

Thanks to Viktor Ilijašić <viktor.ilijasic@gmail.com> and Xose Vazquez
Perez <xose.vazquez@gmail.com> for reporting these new ID's.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Current code for the RTL8187 is not returning valid retry information, thus the
rate-setting mechanism is not functioning. As a further complication, this info
is only obtained by reading a register, which cannot be read while in interrupt
context.

This patch implements the TX status return to mac80211 through the use of a
work queue.

One additional problem is that the driver currently enables the rate fallback
mechanism of the device, which conflicts with the mac80211 rate-setting
algorithm. This version of the patch disables rate fallback.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NMartín Ernesto Barreyro <barreyromartin@gmail.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The receive queue depth in rtl8187 may not be long enough to keep
the pipe full.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In rtl8187_add_interface(), the mutex that protects the data in struct
rtl8187_priv does not include all references to that structure.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RTL8187 and RTL8187B devices can stall unless an explicit termination
packet is sent.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to misunderstanding of the returned values allowed for the tx callback
of mac80211, rtl8187 was using skb's that had been freed. This problem was
triggered when the module was sujected to a rmmod/insmod cycle.

After that was fixed, the modules would not work after the rmmod/insmod cycle
until the USB device was reset.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NHin-Tak Leung <htl10@users.sourceforge.net>

After the code was modified to use urb anchors ("rtl8187: Use usb anchor
facilities to manage urbs"), rtl8187 began generating an intermittent GPF
on shutdown when using SLUB with debugging enabled. Furthermore, rebooting
the system with a ping running caused a GPF every time. There are two problems:
(1) incorrect locking in the rtl8187_rx_cb() routine, a pre-existing bug that
apparently had not been triggered before, and (2) duplicate freeing of receive
skbs that was probably introduced with the change to anchors.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are two places in the rtl8187 code where a routine was returning zero
(OK) when it should have been returning an error.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When SLUB debugging is enabled in the kernel, and the boot command includes
the option "slub_debug=P", rtl8187 encounters a GPF due to a read-after-free
of a urb.

Following the example of changes in p54usb to fix the same problem, the code
has been modified to use the usb_anchor_urb() method. With this change, the
USB core handles the freeing of urb's.

This patch fixes the problem reported in Kernel Bugzilla #12185
(http://bugzilla.kernel.org/show_bug.cgi?id=12185).
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current wireless statistics for the RTL8187 poorly indicate the signal
strength and quality. With testing, I found that the AGC value is inversely
correlated with the strength as in the RTL8187B. By implementing a similar
calculation, much more code becomes common to the two devices.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I mistakenly changed retry count passed in rtl8187_tx in previous change
"rtl8187: feedback transmitted packets using tx close descriptor for
8187B". For 8187 it should represent the number of retries (retry count
limit). As explained by Johannes Berg, .count represents the number of
tries (not retries), and retries = tries - 1.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the commit entitled "mac80211/drivers: rewrite the rate control
API", the meaning of the packet transmit count was changed from the
number of retries to the total number.  In driver rtl8187, this change
was missed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After considerable testing, the initial fears that the driver might damage
some flavors of RTL8187B hardware seem to be groundless. Accordingly, the
logged warning is removed. In addition, Kconfig is changed to remove the
dependence on EXPERIMENTAL.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Realtek 8187B has a receive command queue to feedback beacon interrupt
and transmitted packet status. Use it to feedback mac80211 about status
of transmitted packets. Unfortunately in the course of testing I found
that the sequence number reported by hardware includes entire sequence
control in a 12 bit only field, so a workaround is done to check only
lowest bits.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add conf_tx callback and use it to configure tx queues of 8187L/8187B.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hin-Tak Leung reported that after the change "rtl8187: add short slot
handling for 8187B" his RTL8187B started to give low throughput on
network transfers. Turns out that the SIFS setting used isn't ok, it
doesn't look to be the real aSIFSTime, using the "magical" 0x22 value
like on other 818x variants as the vendor does too fixes the issue.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Modify the file comments to reflect the current maintainers.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change improves the maintainability of these drivers. No functionality
is changed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvan Kuten <ivan.kuten@promwad.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The latest vendor driver (rtl8187B_linux_26.1036.0708.2008) has a 10 msec
delay after the call to set a new channel, but not before.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each of the primary write routines, rtl8187_write_phy(),
rtl8225_write_bitbang(), and rtl8225_write_8051() all conclude with an
msleep() command. Testing shows that these are not needed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rtl8187 driver contains 3 sleep statements that are longer than
a second. Testing has shown no bad effects when they are removed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change adds short slot handling for 8187B variant of rtl8187 chips.
Some things to note about changes done:
* Values used are chosen to met 802.11-2007 spec. This raised a question
  about SIFS value used with 8187L: 0x22 (34) doesn't match any spec
  value. For now just don't change 8187L, but is something to be
  looked at.
* On 8187B, the location of EIFS register is at the same place as BRSR+1
  of struct rtl818x_csr. Unfortunately there is no clean way to
  accomodate 8187B differences currently, just use address of BRSR+1 and
  comment about it. The same thing happens for Ack timeout register,
  that is on CARRIER_SENSE_COUNTER location of 8187L. The eifs and ack
  timeout values are in units of 4us. All these registers information
  was gathered from references being the vendor gpl driver and 8180
  datasheet, unfortunately there is no information about this on 8187B
  datasheet. Also the ack timeout value was inspired by the same
  calculation as done on rt2x00.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates 8187L handling for short slot after "mac80211: fix short
slot handling". For 8187B, there was no handling done for short slot
timing so nothing done, support for it will come in a following patch.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sorry about that, for some reason I didn't notice that I'd
left some unused variables in there.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I've come to think that not providing sequence numbers for
the normal STA mode case was a mistake, at least two drivers
now had to implement code they wouldn't otherwise need, and
I believe at76_usb and adm8211 might be broken.

This patch makes mac80211 assign a sequence number to all
those frames that need one except beacons. That means that
if a driver only implements modes that do not do beaconing
it need not worry about the sequence number.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.

No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.

Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Belkin F5D7050rev5000de (id 050d:705e) has the Realtek RTL8187B chip
and works with the 2.6.27 driver.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported by zOOmER.gm@gmail.com to work here:

	http://bugzilla.kernel.org/show_bug.cgi?id=11728Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>