Add an option to notify mac80211 about sched scan complete from
iwl_mvm_stop_sched_scan(), to enable this notification when the
stop was called from within the driver.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The 8000 family products need a file on the file system
which is used as NVM. This file is a must, if no filename
is supplied as module parameter, use a default filename.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NDor Shaish <dor.shaish@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All messages should have a trailing newline, add all the
missing ones. Also make all messages constants, replacing
the single one that pointlessly used a variable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

After fixes to the rs algorithm reenable MCS9.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the declaration of iwl_mvm_fw_error_rxf_dump and
iwl_mvm_fw_error_sram_dump is under
ifdef CONFIG_IWLWIFI_DEBUGFS, do the same for their
implementation.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows mac80211 to flush the Tx queues before it sends
critical management frames.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Publish WIPHY_FLAG_HAS_CHANNEL_SWITCH if the fw supports
newly introduced IWL_UCODE_TLV_API_CSA_FLOW.
When CSA starts, save the switching vif inside mvm and during the CSA period
configure fw with a new beacon after each beacon transmission in order to
update the csa counters.
Also, handle correctly the CSA unbind-bind flow which is triggered by mac80211
when the actual channel switch happens.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some ampdu actions change queues by direct target access.

Since the bus is disabled in d0i3, make sure to exit d0i3
before handling these actions.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When a firmware error occurs, capture the last 32 commands
(which are still in memory) in the error dump debugfs file.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If there's no LED on the system, it doesn't make a lot of sense
to include close to 4k of LED-related code (mostly in mac80211),
so instead of forcing LED support into the kernel, don't build
iwlwifi/mac80211 LED support if there's no LED class support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEliadX Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The old code checks if hw_section_num is valid while the
right thing to do is to check if section[hw_section_num].data
is valid.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Read first the nvm sections from the OTP, then read the nvm
sections from the external file and override the OTP values
(if there were any values in the OTP).
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NDor Shaish <dor.shaish@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A few devices aren't allowed to be powered up at driver
load time. Add "power_up_nic_in_init" flag to iwl_cfg
structure to customize the load flow according to the
device.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

OTP size changed in family 7000 and in family 8000.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to use a variable just to return the result
of another function call at the end of a function, remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The expected throughput table used when estimating a new column
depends on the channel bandwidth. When switching from legacy to
siso or mimo the wrong expected throughput table was used as it
was chosen based on the the channel bandwidth in legacy which is
always 20Mhz. Instead it should be chosen based on the current sta
bandwidth which could be also 40Mhz or 80Mhz.
When enabling MCS9 this bug leads to a problem where the max
expected throughput of the siso or mimo column is 0 as MCS9 isn't
supported in 20Mhz. This in turns prevents switching to siso or mimo.

Fix this by using the sta bandwidth when deciding which table to choose.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

TPC is a power optimization which should only be attempted when
we're in the "stay in column" state after we've locked onto an optimal
rate.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently we were checking only if the driver power_scheme is set
to CAM. TPC shouldn't be enabled also when disabling powersave on the
interface (e.g. iw wlan0 set power_save off)
which may occur even if power_scheme wasn't set to CAM.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

rs_get_best_rate determines the optimal rate to try in a
new Tx column. Currently we were sometimes trying a too high
rate which would lead us to fail and avoid switching to the
new column despite it having a potential to be better.
Change the logic to try and find the first rate which would
exceed the current actual throughput or be more aggressive
if the success ratio is good.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Adding more options in the search cycle causes longer
search cycles with additional wondering off to non optimal Tx
configurations. Reduce the Tx configurations searched to
improve throughput in non optimal attenuations.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

My bad - I forgot to update this when sending the patch
upstream.

Fixes: 87d5e415 ("iwlwifi: mvm: rs: reinit rs if no tx for a long time")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The commit below introduced a bug in the validity bits in
init. Due to that, all the Coex mechanism stopped sending
kills to the BT side. Fix that.

Fixes: b9fae2d5 ("iwlwifi: mvm: BT Coex add support for Co-running block")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver can enable uAPSD and specify some of its related parameters.
This patch organizes this logic in a separate function.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Somehow I added spaces instead of tabs to a few lines in
debugfs.c.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

bail out from the suspend/resume callbacks if
d0i3 is used.

declare support for ANY wowlan trigger (i.e.
normal operation).

On resume, we shouldn't execute the d0i3 exit
flow (which might disconnect stations, etc.)
until mac80211 was resumed.
Add new flags to indicate we are in suspend,
and call the pending exit work on resume.

Since the resume flow can take some time, add
a new EXIT_WORK reference type to prevent going
back to d0i3 at this stage.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Calling iwl_send_bt_init_conf for INIT firmware is not a
problem, and calling iwl_send_bt_prio_tbl from
iwl_send_bt_init_conf allows us to prepare for new API.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The BT Coex API underwent a minor backward compatible API
change.
We now need to set an invalid value in the override fields.
While at it, add kerneldoc comments on the fields in the
command.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is really not needed. This is a remainder from a C99
initialiser.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>