The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:

commit 6d93c0c4 ("drm/i915: fix VDD state tracking after system
resume")

At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).

While at it remove an unnecessary function call indirection.

This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
(cherry picked from commit bf93ba67)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.

This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.

v2:
- Add a code comment about the relation of this fix to the freeze/thaw
  vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
  and device enable calls. (Chris)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: stable@vger.kernel.org
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460979954-14503-1-git-send-email-imre.deak@intel.com
(cherry picked from commit 44410cd0)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: NRafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes: 5008e874 ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.ukAcked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit acf4e84d)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org

Was previously always hardcoded to 0.
Signed-off-by: NSonny Jiang <sonny.jiang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).

This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.

So to be safe just add a check to verify_access() callback.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NJérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).

This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.

So to be safe just add a check to verify_access() callback.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NJérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fixes array overflow on these chips.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Prerequiste for the next patch which ups the limits.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

With the joys of things running concurrently, there's always a chance
that the port we get passed in drm_dp_payload_send_msg() isn't actually
valid anymore. Because of this, we need to make sure we validate the
reference to the port before we use it otherwise we risk running into
various race conditions. For instance, on the Dell MST monitor I have
here for testing, hotplugging it enough times causes us to kernel panic:

[drm:intel_mst_enable_dp] 1
[drm:drm_dp_update_payload_part2] payload 0 1
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00200000, dig 0x10101011, pins 0x00000020
[drm:intel_hpd_irq_handler] digital hpd port B - short
[drm:intel_dp_hpd_pulse] got hpd irq on port B - short
[drm:intel_dp_check_mst_status] got esi 00 10 00
[drm:drm_dp_update_payload_part2] payload 1 1
general protection fault: 0000 [#1] SMP
…
Call Trace:
 [<ffffffffa012b632>] drm_dp_update_payload_part2+0xc2/0x130 [drm_kms_helper]
 [<ffffffffa032ef08>] intel_mst_enable_dp+0xf8/0x180 [i915]
 [<ffffffffa0310dbd>] haswell_crtc_enable+0x3ed/0x8c0 [i915]
 [<ffffffffa030c84d>] intel_atomic_commit+0x5ad/0x1590 [i915]
 [<ffffffffa01db877>] ? drm_atomic_set_crtc_for_connector+0x57/0xe0 [drm]
 [<ffffffffa01dc4e7>] drm_atomic_commit+0x37/0x60 [drm]
 [<ffffffffa0130a3a>] drm_atomic_helper_set_config+0x7a/0xb0 [drm_kms_helper]
 [<ffffffffa01cc482>] drm_mode_set_config_internal+0x62/0x100 [drm]
 [<ffffffffa01d02ad>] drm_mode_setcrtc+0x3cd/0x4e0 [drm]
 [<ffffffffa01c18e3>] drm_ioctl+0x143/0x510 [drm]
 [<ffffffffa01cfee0>] ? drm_mode_setplane+0x1b0/0x1b0 [drm]
 [<ffffffff810f79a7>] ? hrtimer_start_range_ns+0x1b7/0x3a0
 [<ffffffff81212962>] do_vfs_ioctl+0x92/0x570
 [<ffffffff81590852>] ? __sys_recvmsg+0x42/0x80
 [<ffffffff81212eb9>] SyS_ioctl+0x79/0x90
 [<ffffffff816b4e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
RIP  [<ffffffffa012b026>] drm_dp_payload_send_msg+0x146/0x1f0 [drm_kms_helper]

Which occurs because of the hotplug event shown in the log, which ends
up causing DRM's dp helpers to drop the port we're updating the payload
on and panic.

CC: stable@vger.kernel.org
Signed-off-by: NLyude <cpaul@redhat.com>
Reviewed-by: NDavid Airlie <airlied@linux.ie>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It will help identify problematic boards.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit e64c952e.

ATPX is the ACPI method for controlling AMD PowerXpress laptops.
There are flags to indicate which methods are supported.  If
the dGPU power down flag is not supported, the driver needs to
implement the dGPU power down manually.  We had previously
always forced the driver to assume the ATPX dGPU power down
was present, but this causes problems on boards where it is
not, leading to GPU hangs when attempting to power down the
dGPU.  Manual dGPU power down is not currently supported in
the Linux driver.  Some laptops indicate that the ATPX
dGPU power down method is not present, but it actually
apparently is.  I'm not sure if this is a bios bug and it should
be set or if there is a reason it was unset and the method should
not be used.  This is not an issue on other OSes since both the
ATPX and the manual driver power down methods are supported.

This is apparently fairly widespread, so just revert for now.

bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=115321
https://bugzilla.kernel.org/show_bug.cgi?id=116581
https://bugzilla.kernel.org/show_bug.cgi?id=116251

Cc: stable@vger.kernel.org

Nothing to do on resume on systems with AZ audio.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76490Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The pci revision id is useful in debugging certain things as
it's part of how SKUs are defined on newer asics.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

HSW still has the wake FIFO, so let's check it.

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Fixes: 05a2fb15 ("drm/i915: Consolidate forcewake code")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460633942-24013-1-git-send-email-ville.syrjala@linux.intel.com
Cc: stable@vger.kernel.org
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit 3d7d0c85)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

For reasons unknown Sandybridge GT1 (at least) will eventually hang when
it encounters a ring wraparound at offset 0. The test case that
reproduces the bug reliably forces a large number of interrupted context
switches, thereby causing very frequent ring wraparounds, but there are
similar bug reports in the wild with the same symptoms, seqno writes
stop just before the wrap and the ringbuffer at address 0. It is also
timing crucial, but adding various delays hasn't helped pinpoint where
the window lies.

Whether the fault is restricted to the ringbuffer itself or the GTT
addressing is unclear, but moving the ringbuffer fixes all the hangs I
have been able to reproduce.

References: (e.g.) https://bugs.freedesktop.org/show_bug.cgi?id=93262
Testcase: igt/gem_exec_whisper/render-contexts-interruptible #snb-gt1
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-12-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit a687a43a)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

We started to use PIPE_CONTROL to write render ring seqno in order to
combat seqno write vs interrupt generation problems. This was introduced
by commit 7c17d377 ("drm/i915: Use ordered seqno write interrupt
generation on gen8+ execlists").

On gen8+ size of PIPE_CONTROL with Post Sync Operation should be
6 dwords. When we're using older 5-dword variant it's possible to
observe inconsistent values written by PIPE_CONTROL with Post
Sync Operation from user batches, resulting in rendering corruptions.

v2: Fix BAT failures
v3: Comments on alignment and thrashing high dword of seqno (Chris)
v4: Updated commit msg (Mika)

Testcase: igt/gem_pipe_control_store_loop/*-qword-write
Issue: VIZ-7393
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: NMichał Winiarski <michal.winiarski@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NAbdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460469115-26002-1-git-send-email-michal.winiarski@intel.com
(cherry picked from commit ce81a65c)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Experiments with heaven 4.0 benchmark and skylake gt3e (rev 0xa)
suggest that WaForceContextSaveRestoreNonCoherent is needed for all
revs. Extending this to all revs cures a gpu hang with rev 0xa when
running heaven4.0 gpu benchmark.

We have been here before, with problems enabling gt4e and extending
up to revision F0 instead of false claims of bspec of E0 only. See
commit <e238659d> ("drm/i915/skl: Default to noncoherent access
up to F0"). In retrospect we should have covered this with this big
blanket back then already, as E0 vs F0 discrepancy was suspicious
enough.

Previously the WaForceEnableNonCoherent has been tied to
context non-coherence, atleast in relevant hsds. So keep this tie
and extended this alongside.

Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: stable@vger.kernel.org
Reported-by: NMike Lothian <mike@fireburn.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=93491Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NBen Widawsky <benjamin.widawsky@intel.com>
Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459860977-27751-2-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 97ea6be1)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

For all gt3 and gt4 skylake variants, extend the usage of
WaRsDisableCoarsePowerGating for all revisions. Without this
gt3 and gt4 skylakes up to atleast rev 0xa can gpu hang or
system hang.

Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: <stable@vger.kernel.org>
Reported-by: NMikael Djurfeldt <mikael@djurfeldt.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=94161Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NBen Widawsky <benjamin.widawsky@intel.com>
Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459860977-27751-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 185c66e5)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Holding a reference to the containing task_struct is not sufficient to
prevent the mm_struct from being reaped under memory pressure. If this
happens whilst we are calling get_user_pages(), explosions erupt -
sometimes an immediate GPF, sometimes page flag corruption. To prevent
the target mm from being reaped as we are reading from it, acquire a
reference before we begin.

Testcase: igt/gem_shrink/*userptr
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-2-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 40313f0c)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Currently for the case where there is enough space at the end of Ring
buffer for accommodating only the base request, the wrapround is done
immediately and as a result the base request gets added at the start
of Ring buffer. But there may not be enough free space at the beginning
to accommodate the base request, as before the wraparound, the wait was
effectively done for the reserved_size free space from the start of
Ring buffer. In such a case there is a potential of Ring buffer overflow,
the instructions at the head of Ring (ACTHD) can get overwritten.

Since the base request can fit in the remaining space, there is no need
to wraparound immediately. The wraparound will anyway happen later when
the reserved part starts getting used.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1457688402-10411-1-git-send-email-akash.goel@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
(cherry picked from commit 782f6bc0)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Use plane size for relative data rate calculation. don't always use
pipe source width & height.
adjust height & width according to rotation.
use plane size for watermark calculations also.

v2: Address Matt's comments.
    Use intel_plane_state->visible to avoid divide-by-zero error.
    Where FB was present but not visible so causing total data rate to
    be zero, hence divide-by-zero.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93917
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94044
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NKumar, Mahesh <mahesh1.kumar@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459956399-1296-1-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit a280f7dd)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

fix the issue that when resume back, uvd/vce
dpm was disabled and uvd/vce's performace
dropped.
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This got lost somewhere along the way.  This fixes
audio not working until set_property was called.
Noticed-by: NHyungwon Hwang <hyungwon.hwang7@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Commit 254d4d11 ("drm/exynos: Add dependency for G2D in Kconfig") made
the DRM_EXYNOS_G2D symbol to only be selectable if the s5p-g2d V4L2 driver
is not enabled, since both use the same HW IP block.

But added the dependency as depends on !VIDEO_SAMSUNG_S5P_G2D which isn't
correct since Kconfig expressions are not boolean but tristate. So it will
only evaluate to 'n' if VIDEO_SAMSUNG_S5P_G2D=y but it will evaluate to m
if VIDEO_SAMSUNG_S5P_G2D=m.

This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which is not what we want.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The "ret = regmap_write()" assignment was missing so this error message
is never printed.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

We accidentally return success instead of a negative error code here.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Commit 1feafd3a ("drm/exynos: add
exynos5420 support for fimd") add support for Exynos 5420 SoC, but it
broke enabling display clock feature because of incorrect condition
check. This patch fixes it, so display is working again on platforms
requiring display clock control (i.e. Exynos5250-based SNOW platform).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Fbdev code should be compiled only if CONFIG_DRM_FBDEV_EMULATION option
is enabled. The patch fixes exynos-drm code trying to manipulate
fbdev data which is not initialized in case CONFIG_DRM_FBDEV_EMULATION
is disabled.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

exynos_plane_mode_set should use adjusted_mode from the same atomic state as
plane state. Otherwise it will result in incorrect behavior in case
crtc mode changes.

The patch fixes bug with black console framebuffer in case of command mode
panels.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

gcc-6 warns about a pointless loop in exynos_drm_subdrv_open:

drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open':
drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare]
  list_for_each_entry_reverse(subdrv, &subdrv->list, list) {

Here, the list_for_each_entry_reverse immediately terminates because
the subdrv pointer is compared to itself as the loop end condition.

If we were to take the current subdrv pointer as the start of the
list (as we would do if list_for_each_entry_reverse() was not a macro),
we would iterate backwards over the &exynos_drm_subdrv_list anchor,
which would be even worse.

Instead, we need to use list_for_each_entry_continue_reverse()
to go back over each subdrv that was successfully opened until
the first entry.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Signed-off-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

commit e2c8b870 moved modeset locking inside resume/suspend
functions, but missed a code path only executed on lid close/open
on older hardware. The result was a deadlock when closing and
opening the lid without suspending on such hardware:

 =============================================
 [ INFO: possible recursive locking detected ]
 4.6.0-rc1 #385 Not tainted
 ---------------------------------------------
 kworker/0:3/88 is trying to acquire lock:
  (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]

 but task is already holding lock:
  (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(&dev->mode_config.mutex);
   lock(&dev->mode_config.mutex);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 7 locks held by kworker/0:3/88:
  #0:  ("kacpi_notify"){++++.+}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
  #1:  ((&dpc->work)#2){+.+.+.}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
  #2:  ((acpi_lid_notifier).rwsem){++++.+}, at: [<ffffffff8106f874>] __blocking_notifier_call_chain+0x34/0x65
  #3:  (&dev_priv->modeset_restore_lock){+.+.+.}, at: [<ffffffffa0664cf6>] intel_lid_notify+0x3c/0xd9 [i915]
  #4:  (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]
  #5:  (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffffa02d0d59>] drm_modeset_lock_all+0x48/0xa6 [drm]
  #6:  (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffffa02d0b2a>] modeset_lock+0x13c/0x1cd [drm]

 stack backtrace:
 CPU: 0 PID: 88 Comm: kworker/0:3 Not tainted 4.6.0-rc1 #385
 Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
 Workqueue: kacpi_notify acpi_os_execute_deferred
  0000000000000000 ffff88022fd5f990 ffffffff8124af06 ffffffff825b39c0
  ffffffff825b39c0 ffff88022fd5fa60 ffffffff8108f547 ffff88022fd5fa70
  000000008108e817 ffff880230236cc0 0000000000000000 ffffffff825b39c0
 Call Trace:
  [<ffffffff8124af06>] dump_stack+0x67/0x90
  [<ffffffff8108f547>] __lock_acquire+0xdb5/0xf71
  [<ffffffff8108bd2c>] ? look_up_lock_class+0xbe/0x10a
  [<ffffffff8108fae2>] lock_acquire+0x137/0x1cb
  [<ffffffff8108fae2>] ? lock_acquire+0x137/0x1cb
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffff8148202f>] mutex_lock_nested+0x7e/0x3a4
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
  [<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
  [<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
  [<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
  [<ffffffffa02d0bf7>] ? drm_modeset_lock+0x17/0x24 [drm]
  [<ffffffffa02d0c8b>] ? drm_modeset_lock_all_ctx+0x87/0xa1 [drm]
  [<ffffffffa0664d6a>] intel_lid_notify+0xb0/0xd9 [i915]
  [<ffffffff8106f4c6>] notifier_call_chain+0x4a/0x6c
  [<ffffffff8106f88d>] __blocking_notifier_call_chain+0x4d/0x65
  [<ffffffff8106f8b9>] blocking_notifier_call_chain+0x14/0x16
  [<ffffffffa0011215>] acpi_lid_send_state+0x83/0xad [button]
  [<ffffffffa00112a6>] acpi_button_notify+0x41/0x132 [button]
  [<ffffffff812b07df>] acpi_device_notify+0x19/0x1b
  [<ffffffff812c8570>] acpi_ev_notify_dispatch+0x49/0x64
  [<ffffffff812ab9fb>] acpi_os_execute_deferred+0x14/0x20
  [<ffffffff81068f17>] process_one_work+0x265/0x50b
  [<ffffffff810696f5>] worker_thread+0x1fc/0x2dd
  [<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
  [<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
  [<ffffffff8106e2d6>] kthread+0xe0/0xe8
  [<ffffffff8107bc47>] ? local_clock+0x19/0x22
  [<ffffffff81484f42>] ret_from_fork+0x22/0x40
  [<ffffffff8106e1f6>] ? kthread_create_on_node+0x1b5/0x1b5

Fixes: e2c8b870 ("drm/i915: Use atomic helpers for suspend, v2.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459328913-13719-1-git-send-email-bjorn@mork.no
(cherry picked from commit 9f54d4bd)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

I noticed my monitor didn't power off when it should,
this should fix it.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This ports the DAL timeouts and MST rate calculations
for the hw from the DAL codebase.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

GM20B requires an extra clock compared to GK20A. Add that information
into the platform data and acquire and enable this clock if necessary.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NChunming Zhou <David1.Zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>