Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.

The following 2 patches will convert the drivers to OF.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The PMIC device RC5T583 from RICOH supports 8 gpios.
Adding gpio driver for this device to access the pins
control through gpio library.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[grant.likely: slight cosmetic changes]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch is V2 of the Emma Mobile GPIO driver. This
driver is designed to be reusable between multiple SoCs
that share the same basic building block, but so far it
has only been used on Emma Mobile EV2.

Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on two I/O memory
ranges and the 32 GPIOs are hooked up to two interrupts.

In the case of Emma Mobile EV2 this GPIO building block
is used as main external interrupt controller hooking up
159 GPIOS as 159 interrupts via 5 driver instances and
10 interrupts to the GIC and the Cortex-A9 Dual.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Add gpio support for Intel MSIC chips found in Intel Medfield platforms.
MSIC supports totally 24 GPIOs with 16 low voltage and 8 high voltage pins.
Driver uses MSIC mfd interface for MSIC access.

(Updated comment to indicate why locking is actually safe)
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

I'm moving this driver over to the pinctrl subsystem to convert
the custom pin mux/config scheme over to use pinctrl.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This introduces 128 gpio bits (for each PCI device installed) with
working interrupt support.
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver works on many Intel chipsets, including the ICH6, ICH7,
ICH8, ICH9, ICH10, 3100, Series 5/3400 (Ibex Peak), Series 6/C200
(Cougar Point), and NM10 (Tiger Point).

Additional Intel chipsets should be easily supported if needed, eg the
ICH1-5, EP80579, etc.

Tested on QM67 (Cougar Point), QM57 (Ibex Peak), 3100 (Whitmore Lake),
and NM10 (Tiger Point).

Includes work from Jean Delvare:
        - Resource leak removal during module load/unload
        - GPIO API bit value enforcement

Also includes code cleanup from Guenter Roeck and Grant Likely.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The code in drivers/of/gpio.c isn't shared by any other subsystem since it
is all gpiolib specific.  drivers/gpio is a better place to maintain these
functions.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>

The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.
Signed-off-by: NMartyn Welch <martyn.welch@ge.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.

The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.

In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
	                add some device tree entries.]
Signed-off-by: NTorben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

we only use the gpio function of mc9s08dz60 mcu chip, so just
add the gpio driver, as this mcu will never be used in other board.
Signed-off-by: NWu Guoxing <b39297@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds 2 functions that allow managed devices to request GPIOs.
These GPIOs will then be managed by drivers/base/devres.c.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This driver will be converted to a dual GPIO + pinctrl driver
since it supports biasing and driving control options. Hopefully
it can serve as an example.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

I screwed up by compiling that driver for the machine rather
than the arch. Correcting this fixes the build error.

Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove most gpio macros and change gpio driver to platform driver.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>

As per example from the other ARM boards, push the PXA
GPIO driver down to the GPIO subsystem so it can be consolidated.
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

This patch adds support for Samsung GPIOs with one gpio driver
and removes old GPIO drivers which are drivers/gpio-s3c24xx.c,
gpio-s3c64xx.c, gpio-s5p64x0.c, gpio-s5pc100.c, gpio-s5pv210.c,
gpio-exynos4.c, gpio-plat-samsung.c, plat-samsung/gpio-config.c
and gpio.c to support each Samsung SoCs before. Because the
gpio-samsung.c can replace old Samsung GPIO drivers.
Basically, the gpio-samsung.c has been made by their merging
and removing duplicated definitions.

Note: gpio-samsung.c includes some SoC dependent codes and it
will be replaced next time.

Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: squash the removing and adding patches]
[kgene.kim@samsung.com: fixes bug during to register of gpio_chips]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As per example from the other ARM boards, push the SA100
GPIO driver down to the GPIO subsystem so it can be consolidated.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As per example from the other ARM boards, push the LPC32XX
GPIO driver down to the GPIO subsystem so it can be consolidated.

Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As per example from the other ARM boards, push the DaVinci TNET
GPIO driver down to the GPIO subsystem so it can be consolidated.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As per example from the other ARM boards, push the DaVinci GPIO
driver down to the GPIO subsystem so it can be consolidated.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As per example from the other ARM boards, push the KS8695 GPIO
driver down to the GPIO subsystem so it can be consolidated.

Cc: zeal <zealcook@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: NDaniel Silverstone <dsilvers@simtec.co.uk>
Acked-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Migrate the driver for the v7-based MSM chips into drivers/gpio.  The
driver is unchanged, only moved.

Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>

Migrate the driver for the v6-based MSM chips into drivers/gpio.  The
driver is unchanged, only moved.

Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>

TPS65912 has five GPIOs that can be configured for different
purposes.
Signed-off-by: NMargarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

GPIO drivers are getting consolidated into drivers/gpio.  While at it,
change the driver name to mpc5200-gpio* to avoid collisions.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

DA9052 PMIC has 16 bit GPIO bus for peripheral control.

This patch add support for the GPIO pins on the DA9052.
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

As part of the gpio driver consolidation, this patch moves the Tegra driver
into drivers/gpio
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NColin Cross <ccross@android.com>

Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.

v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The GPIO driver should reside in drivers/gpio.

v3: Change Kconfig option to def_bool y
v2: Make the Kconfig symbol a silent option, dependent on ARCH_EP93XX
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the plat-mxc driver.  Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation.  This patch moves the mxs driver.  Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.

v2: Removed header file entirely and put struct definition directly
    into driver.  The struct isn't used anywhere else in the kernel.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Move OMAP GPIO driver to drivers/gpio.  Builds whenever
CONFIG_ARCH_OMAP=y.
Signed-off-by: NKevin Hilman <khilman@ti.com>

The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: NJorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Move the Samsung s5pc100 SoC GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Move the Samsung s5pv210 SoC GPIO driver to drivers/gpio
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>