Values assigned to both variable resend_at and ack_at are overwritten
before they can be used.

The correct fix here is to add 'now' to the previously computed value in
resend_at and ack_at.

Addresses-Coverity-ID: 1462262
Addresses-Coverity-ID: 1462263
Addresses-Coverity-ID: 1462264
Fixes: beb8e5e4 ("rxrpc: Express protocol timeouts in terms of RTT")
Link: https://marc.info/?i=17004.1511808959%40warthog.procyon.org.ukSigned-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Clean up some whitespace from rxrpc.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

We need to transmit a packet every so often to act as a keepalive for the
peer (which has a timeout from the last time it received a packet) and also
to prevent any intervening firewalls from closing the route.

Do this by resetting a timer every time we transmit a packet.  If the timer
ever expires, we transmit a PING ACK packet and thereby also elicit a PING
RESPONSE ACK from the other side - which prevents our last-rx timeout from
expiring.

The timer is set to 1/6 of the last-rx timeout so that we can detect the
other side going away if it misses 6 replies in a row.

This is particularly necessary for servers where the processing of the
service function may take a significant amount of time.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add an extra timeout that is set/updated when we send a DATA packet that
has the request-ack flag set.  This allows us to detect if we don't get an
ACK in response to the latest flagged packet.

The ACK packet is adjudged to have been lost if it doesn't turn up within
2*RTT of the transmission.

If the timeout occurs, we schedule the sending of a PING ACK to find out
the state of the other side.  If a new DATA packet is ready to go sooner,
we cancel the sending of the ping and set the request-ack flag on that
instead.

If we get back a PING-RESPONSE ACK that indicates a lower tx_top than what
we had at the time of the ping transmission, we adjudge all the DATA
packets sent between the response tx_top and the ping-time tx_top to have
been lost and retransmit immediately.

Rather than sending a PING ACK, we could just pick a DATA packet and
speculatively retransmit that with request-ack set.  It should result in
either a REQUESTED ACK or a DUPLICATE ACK which we can then use in lieu the
a PING-RESPONSE ACK mentioned above.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Express protocol timeouts for data retransmission and deferred ack
generation in terms on RTT rather than specified timeouts once we have
sufficient RTT samples.

For the moment, this requires just one RTT sample to be able to use this
for ack deferral and two for data retransmission.

The data retransmission timeout is set at RTT*1.5 and the ACK deferral
timeout is set at RTT.

Note that the calculated timeout is limited to a minimum of 4ns to make
sure it doesn't happen too quickly.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Fix the rxrpc call expiration timeouts and make them settable from
userspace.  By analogy with other rx implementations, there should be three
timeouts:

 (1) "Normal timeout"

     This is set for all calls and is triggered if we haven't received any
     packets from the peer in a while.  It is measured from the last time
     we received any packet on that call.  This is not reset by any
     connection packets (such as CHALLENGE/RESPONSE packets).

     If a service operation takes a long time, the server should generate
     PING ACKs at a duration that's substantially less than the normal
     timeout so is to keep both sides alive.  This is set at 1/6 of normal
     timeout.

 (2) "Idle timeout"

     This is set only for a service call and is triggered if we stop
     receiving the DATA packets that comprise the request data.  It is
     measured from the last time we received a DATA packet.

 (3) "Hard timeout"

     This can be set for a call and specified the maximum lifetime of that
     call.  It should not be specified by default.  Some operations (such
     as volume transfer) take a long time.

Allow userspace to set/change the timeouts on a call with sendmsg, using a
control message:

	RXRPC_SET_CALL_TIMEOUTS

The data to the message is a number of 32-bit words, not all of which need
be given:

	u32 hard_timeout;	/* sec from first packet */
	u32 idle_timeout;	/* msec from packet Rx */
	u32 normal_timeout;	/* msec from data Rx */

This can be set in combination with any other sendmsg() that affects a
call.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Fix call expiry handling in the following ways

 (1) If all the request data from a client call is acked, don't send a
     follow up IDLE ACK with firstPacket == 1 and previousPacket == 0 as
     this appears to fool some servers into thinking everything has been
     accepted.

 (2) Never send an abort back to the server once it has ACK'd all the
     request packets; rather just try to reuse the channel for the next
     call.  The first request DATA packet of the next call on the same
     channel will implicitly ACK the entire reply of the dead call - even
     if we haven't transmitted it yet.

 (3) Don't send RX_CALL_TIMEOUT in an ABORT packet, librx uses abort codes
     to pass local errors to the caller in addition to remote errors, and
     this is meant to be local only.

The following also need to be addressed in future patches:

 (4) Service calls should send PING ACKs as 'keep alives' if the server is
     still processing the call.

 (5) VERSION REPLY packets should be sent to the peers of service
     connections to act as keep-alives.  This is used to keep firewall
     routes in place.  The AFS CM should enable this.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Use negative error codes in struct rxrpc_call::error because that's what
the kernel normally deals with and to make the code consistent.  We only
turn them positive when transcribing into a cmsg for userspace recvmsg.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

We need to generate a DELAY ACK from the service end of an operation if we
start doing the actual operation work and it takes longer than expected.
This will hard-ACK the request data and allow the client to release its
resources.

To make this work:

 (1) We have to set the ack timer and propose an ACK when the call moves to
     the RXRPC_CALL_SERVER_ACK_REQUEST and clear the pending ACK and cancel
     the timer when we start transmitting the reply (the first DATA packet
     of the reply implicitly ACKs the request phase).

 (2) It must be possible to set the timer when the caller is holding
     call->state_lock, so split the lock-getting part of the timer function
     out.

 (3) Add trace notes for the ACK we're requesting and the timer we clear.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

The call's background processor work item needs to notify the socket when
it completes a call so that recvmsg() or the AFS fs can deal with it.
Without this, call expiry isn't handled.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

When a call expires, it must be queued for the background processor to deal
with otherwise a service call that is improperly terminated will just sit
there awaiting an ACK and won't expire.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Separate the output of PING ACKs from the output of other sorts of ACK so
that if we receive a PING ACK and schedule transmission of a PING RESPONSE
ACK, the response doesn't get cancelled by a PING ACK we happen to be
scheduling transmission of at the same time.

If a PING RESPONSE gets lost, the other side might just sit there waiting
for it and refuse to proceed otherwise.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Split rxrpc_send_data_packet() to separate ACK generation (which is more
complicated) from ABORT generation.  This simplifies the code a bit and
fixes the following warning:

In file included from ../net/rxrpc/output.c:20:0:
net/rxrpc/output.c: In function 'rxrpc_send_call_packet':
net/rxrpc/ar-internal.h:1187:27: error: 'top' may be used uninitialized in this function [-Werror=maybe-uninitialized]
net/rxrpc/output.c:103:24: note: 'top' was declared here
net/rxrpc/output.c:225:25: error: 'hard_ack' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

The call timer's concept of a call timeout (of which there are three) that
is inactive is that it is the timeout has the same expiration time as the
call expiration timeout (the expiration timer is never inactive).  However,
I'm not resetting the timeouts when they expire, leading to repeated
processing of expired timeouts when other timeout events occur.

Fix this by:

 (1) Move the timer expiry detection into rxrpc_set_timer() inside the
     locked section.  This means that if a timeout is set that will expire
     immediately, we deal with it immediately.

 (2) If a timeout is at or before now then it has expired.  When an expiry
     is detected, an event is raised, the timeout is automatically
     inactivated and the event processor is queued.

 (3) If a timeout is at or after the expiry timeout then it is inactive.
     Inactive timeouts do not contribute to the timer setting.

 (4) The call timer callback can now just call rxrpc_set_timer() to handle
     things.

 (5) The call processor work function now checks the event flags rather
     than checking the timeouts directly.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Keep that call timeouts as ktimes rather than jiffies so that they can be
expressed as functions of RTT.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

In rxrpc_send_data_packet() make the loss-injection path return through the
same code as the transmission path so that the RTT determination is
initiated and any future timer shuffling will be done, despite the packet
having been binned.

Whilst we're at it:

 (1) Add to the tx_data tracepoint an indication of whether or not we're
     retransmitting a data packet.

 (2) When we're deciding whether or not to request an ACK, rather than
     checking if we're in fast-retransmit mode check instead if we're
     retransmitting.

 (3) Don't invoke the lose_skb tracepoint when losing a Tx packet as we're
     not altering the sk_buff refcount nor are we just seeing it after
     getting it off the Tx list.

 (4) The rxrpc_skb_tx_lost note is then no longer used so remove it.

 (5) rxrpc_lose_skb() no longer needs to deal with rxrpc_skb_tx_lost.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Implement RxRPC slow-start, which is similar to RFC 5681 for TCP.  A
tracepoint is added to log the state of the congestion management algorithm
and the decisions it makes.

Notes:

 (1) Since we send fixed-size DATA packets (apart from the final packet in
     each phase), counters and calculations are in terms of packets rather
     than bytes.

 (2) The ACK packet carries the equivalent of TCP SACK.

 (3) The FLIGHT_SIZE calculation in RFC 5681 doesn't seem particularly
     suited to SACK of a small number of packets.  It seems that, almost
     inevitably, by the time three 'duplicate' ACKs have been seen, we have
     narrowed the loss down to one or two missing packets, and the
     FLIGHT_SIZE calculation ends up as 2.

 (4) In rxrpc_resend(), if there was no data that apparently needed
     retransmission, we transmit a PING ACK to ask the peer to tell us what
     its Rx window state is.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

If we've sent all the request data in a client call but haven't seen any
sign of the reply data yet, schedule an ACK to be sent to the server to
find out if the reply data got lost.

If the server hasn't yet hard-ACK'd the request data, we send a PING ACK to
demand a response to find out whether we need to retransmit.

If the server says it has received all of the data, we send an IDLE ACK to
tell the server that we haven't received anything in the receive phase as
yet.

To make this work, a non-immediate PING ACK must carry a delay.  I've chosen
the same as the IDLE ACK for the moment.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

When determining the resend timer value, we have a value in nsec but the
timer is in jiffies which may be a million or more times more coarse.
nsecs_to_jiffies() rounds down - which means that the resend timeout
expressed as jiffies is very likely earlier than the one expressed as
nanoseconds from which it was derived.

The problem is that rxrpc_resend() gets triggered by the timer, but can't
then find anything to resend yet.  It sets the timer again - but gets
kicked off immediately again and again until the nanosecond-based expiry
time is reached and we actually retransmit.

Fix this by adding 1 to the jiffies-based resend_at value to counteract the
rounding and make sure that the timer happens after the nanosecond-based
expiry is passed.

Alternatives would be to adjust the timestamp on the packets to align
with the jiffie scale or to switch back to using jiffie-timestamps.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add a tracepoint to log in rxrpc_resend() which packets will be
retransmitted.  Note that if a positive ACK comes in whilst we have dropped
the lock to retransmit another packet, the actual retransmission may not
happen, though some of the effects will (such as altering the congestion
management).
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add a tracepoint to log proposed ACKs, including whether the proposal is
used to update a pending ACK or is discarded in favour of an easlier,
higher priority ACK.

Whilst we're at it, get rid of the rxrpc_acks() function and access the
name array directly.  We do, however, need to validate the ACK reason
number given to trace_rxrpc_rx_ack() to make sure we don't overrun the
array.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add a tracepoint to log call timer initiation, setting and expiry.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Fix the call timer in the following ways:

 (1) If call->resend_at or call->ack_at are before or equal to the current
     time, then ignore that timeout.

 (2) If call->expire_at is before or equal to the current time, then don't
     set the timer at all (possibly we should queue the call).

 (3) Don't skip modifying the timer if timer_pending() is true.  This
     indicates that the timer is working, not that it has expired and is
     running/waiting to run its expiry handler.

Also call rxrpc_set_timer() to start the call timer going rather than
calling add_timer().
Signed-off-by: NDavid Howells <dhowells@redhat.com>

When a DATA packet has its initial transmission, we may need to start or
adjust the resend timer.  Without this we end up relying on being sent a
NACK to initiate the resend.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

ktime_add_ms() should be used to add the resend time (in ms) rather than
ktime_add_ns().
Signed-off-by: NDavid Howells <dhowells@redhat.com>

We don't want to send a PING ACK for every new incoming call as that just
adds to the network traffic.  Instead, we send a PING ACK to the first
three that we receive and then once per second thereafter.

This could probably be made adjustable in future.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

In addition to sending a PING ACK to gain RTT data, we can set the
RXRPC_REQUEST_ACK flag on a DATA packet and get a REQUESTED-ACK ACK.  The
ACK packet contains the serial number of the packet it is in response to,
so we can look through the Tx buffer for a matching DATA packet.

This requires that the data packets be stamped with the time of
transmission as a ktime rather than having the resend_at time in jiffies.

This further requires the resend code to do the resend determination in
ktimes and convert to jiffies to set the timer.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add a Tx-phase annotation for packet buffers to indicate that a buffer has
already been retransmitted.  This will be used by future congestion
management.  Re-retransmissions of a packet don't affect the congestion
window managment in the same way as initial retransmissions.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Don't store the rxrpc protocol header in sk_buffs on the transmit queue,
but rather generate it on the fly and pass it to kernel_sendmsg() as a
separate iov.  This reduces the amount of storage required.

Note that the security header is still stored in the sk_buff as it may get
encrypted along with the data (and doesn't change with each transmission).
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Improve sk_buff tracing within AF_RXRPC by the following means:

 (1) Use an enum to note the event type rather than plain integers and use
     an array of event names rather than a big multi ?: list.

 (2) Distinguish Rx from Tx packets and account them separately.  This
     requires the call phase to be tracked so that we know what we might
     find in rxtx_buffer[].

 (3) Add a parameter to rxrpc_{new,see,get,free}_skb() to indicate the
     event type.

 (4) A pair of 'rotate' events are added to indicate packets that are about
     to be rotated out of the Rx and Tx windows.

 (5) A pair of 'lost' events are added, along with rxrpc_lose_skb() for
     packet loss injection recording.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
 

Make the retransmission algorithm use for-loops instead of do-loops and
move the counter increments into the for-statement increment slots.

Though the do-loops are slighly more efficient since there will be at least
one pass through the each loop, the counter increments are harder to get
right as the continue-statements skip them.

Without this, if there are any positive acks within the loop, the do-loop
will cycle forever because the counter increment is never done.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Remove a tab that's on a line that should otherwise be blank.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

The IDLE ACK packet should use the rxrpc_idle_ack_delay setting when the
timer is set for it.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Rewrite the data and ack handling code such that:

 (1) Parsing of received ACK and ABORT packets and the distribution and the
     filing of DATA packets happens entirely within the data_ready context
     called from the UDP socket.  This allows us to process and discard ACK
     and ABORT packets much more quickly (they're no longer stashed on a
     queue for a background thread to process).

 (2) We avoid calling skb_clone(), pskb_pull() and pskb_trim().  We instead
     keep track of the offset and length of the content of each packet in
     the sk_buff metadata.  This means we don't do any allocation in the
     receive path.

 (3) Jumbo DATA packet parsing is now done in data_ready context.  Rather
     than cloning the packet once for each subpacket and pulling/trimming
     it, we file the packet multiple times with an annotation for each
     indicating which subpacket is there.  From that we can directly
     calculate the offset and length.

 (4) A call's receive queue can be accessed without taking locks (memory
     barriers do have to be used, though).

 (5) Incoming calls are set up from preallocated resources and immediately
     made live.  They can than have packets queued upon them and ACKs
     generated.  If insufficient resources exist, DATA packet #1 is given a
     BUSY reply and other DATA packets are discarded).

 (6) sk_buffs no longer take a ref on their parent call.

To make this work, the following changes are made:

 (1) Each call's receive buffer is now a circular buffer of sk_buff
     pointers (rxtx_buffer) rather than a number of sk_buff_heads spread
     between the call and the socket.  This permits each sk_buff to be in
     the buffer multiple times.  The receive buffer is reused for the
     transmit buffer.

 (2) A circular buffer of annotations (rxtx_annotations) is kept parallel
     to the data buffer.  Transmission phase annotations indicate whether a
     buffered packet has been ACK'd or not and whether it needs
     retransmission.

     Receive phase annotations indicate whether a slot holds a whole packet
     or a jumbo subpacket and, if the latter, which subpacket.  They also
     note whether the packet has been decrypted in place.

 (3) DATA packet window tracking is much simplified.  Each phase has just
     two numbers representing the window (rx_hard_ack/rx_top and
     tx_hard_ack/tx_top).

     The hard_ack number is the sequence number before base of the window,
     representing the last packet the other side says it has consumed.
     hard_ack starts from 0 and the first packet is sequence number 1.

     The top number is the sequence number of the highest-numbered packet
     residing in the buffer.  Packets between hard_ack+1 and top are
     soft-ACK'd to indicate they've been received, but not yet consumed.

     Four macros, before(), before_eq(), after() and after_eq() are added
     to compare sequence numbers within the window.  This allows for the
     top of the window to wrap when the hard-ack sequence number gets close
     to the limit.

     Two flags, RXRPC_CALL_RX_LAST and RXRPC_CALL_TX_LAST, are added also
     to indicate when rx_top and tx_top point at the packets with the
     LAST_PACKET bit set, indicating the end of the phase.

 (4) Calls are queued on the socket 'receive queue' rather than packets.
     This means that we don't need have to invent dummy packets to queue to
     indicate abnormal/terminal states and we don't have to keep metadata
     packets (such as ABORTs) around

 (5) The offset and length of a (sub)packet's content are now passed to
     the verify_packet security op.  This is currently expected to decrypt
     the packet in place and validate it.

     However, there's now nowhere to store the revised offset and length of
     the actual data within the decrypted blob (there may be a header and
     padding to skip) because an sk_buff may represent multiple packets, so
     a locate_data security op is added to retrieve these details from the
     sk_buff content when needed.

 (6) recvmsg() now has to handle jumbo subpackets, where each subpacket is
     individually secured and needs to be individually decrypted.  The code
     to do this is broken out into rxrpc_recvmsg_data() and shared with the
     kernel API.  It now iterates over the call's receive buffer rather
     than walking the socket receive queue.

Additional changes:

 (1) The timers are condensed to a single timer that is set for the soonest
     of three timeouts (delayed ACK generation, DATA retransmission and
     call lifespan).

 (2) Transmission of ACK and ABORT packets is effected immediately from
     process-context socket ops/kernel API calls that cause them instead of
     them being punted off to a background work item.  The data_ready
     handler still has to defer to the background, though.

 (3) A shutdown op is added to the AF_RXRPC socket so that the AFS
     filesystem can shut down the socket and flush its own work items
     before closing the socket to deal with any in-progress service calls.

Future additional changes that will need to be considered:

 (1) Make sure that a call doesn't hog the front of the queue by receiving
     data from the network as fast as userspace is consuming it to the
     exclusion of other calls.

 (2) Transmit delayed ACKs from within recvmsg() when we've consumed
     sufficiently more packets to avoid the background work item needing to
     run.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add a tracepoint for working out where local aborts happen.  Each
tracepoint call is labelled with a 3-letter code so that they can be
distinguished - and the DATA sequence number is added too where available.

rxrpc_kernel_abort_call() also takes a 3-letter code so that AFS can
indicate the circumstances when it aborts a call.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

rxrpc calls shouldn't hold refs on the sock struct.  This was done so that
the socket wouldn't go away whilst the call was in progress, such that the
call could reach the socket's queues.

However, we can mark the socket as requiring an RCU release and rely on the
RCU read lock.

To make this work, we do:

 (1) rxrpc_release_call() removes the call's call user ID.  This is now
     only called from socket operations and not from the call processor:

	rxrpc_accept_call() / rxrpc_kernel_accept_call()
	rxrpc_reject_call() / rxrpc_kernel_reject_call()
	rxrpc_kernel_end_call()
	rxrpc_release_calls_on_socket()
	rxrpc_recvmsg()

     Though it is also called in the cleanup path of
     rxrpc_accept_incoming_call() before we assign a user ID.

 (2) Pass the socket pointer into rxrpc_release_call() rather than getting
     it from the call so that we can get rid of uninitialised calls.

 (3) Fix call processor queueing to pass a ref to the work queue and to
     release that ref at the end of the processor function (or to pass it
     back to the work queue if we have to requeue).

 (4) Skip out of the call processor function asap if the call is complete
     and don't requeue it if the call is complete.

 (5) Clean up the call immediately that the refcount reaches 0 rather than
     trying to defer it.  Actual deallocation is deferred to RCU, however.

 (6) Don't hold socket refs for allocated calls.

 (7) Use the RCU read lock when queueing a message on a socket and treat
     the call's socket pointer according to RCU rules and check it for
     NULL.

     We also need to use the RCU read lock when viewing a call through
     procfs.

 (8) Transmit the final ACK/ABORT to a client call in rxrpc_release_call()
     if this hasn't been done yet so that we can then disconnect the call.
     Once the call is disconnected, it won't have any access to the
     connection struct and the UDP socket for the call work processor to be
     able to send the ACK.  Terminal retransmission will be handled by the
     connection processor.

 (9) Release all calls immediately on the closing of a socket rather than
     trying to defer this.  Incomplete calls will be aborted.

The call refcount model is much simplified.  Refs are held on the call by:

 (1) A socket's user ID tree.

 (2) A socket's incoming call secureq and acceptq.

 (3) A kernel service that has a call in progress.

 (4) A queued call work processor.  We have to take care to put any call
     that we failed to queue.

 (5) sk_buffs on a socket's receive queue.  A future patch will get rid of
     this.

Whilst we're at it, we can do:

 (1) Get rid of the RXRPC_CALL_EV_RELEASE event.  Release is now done
     entirely from the socket routines and never from the call's processor.

 (2) Get rid of the RXRPC_CALL_DEAD state.  Calls now end in the
     RXRPC_CALL_COMPLETE state.

 (3) Get rid of the rxrpc_call::destroyer work item.  Calls are now torn
     down when their refcount reaches 0 and then handed over to RCU for
     final cleanup.

 (4) Get rid of the rxrpc_call::deadspan timer.  Calls are cleaned up
     immediately they're finished with and don't hang around.
     Post-completion retransmission is handled by the connection processor
     once the call is disconnected.

 (5) Get rid of the dead call expiry setting as there's no longer a timer
     to set.

 (6) rxrpc_destroy_all_calls() can just check that the call list is empty.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Improve the call tracking tracepoint by showing more differentiation
between some of the put and get events, including:

  (1) Getting and putting refs for the socket call user ID tree.

  (2) Getting and putting refs for queueing and failing to queue the call
      processor work item.

Note that these aren't necessarily used in this patch, but will be taken
advantage of in future patches.

An enum is added for the event subtype numbers rather than coding them
directly as decimal numbers and a table of 3-letter strings is provided
rather than a sequence of ?: operators.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Fix the following uninitialised variable warning:

../net/rxrpc/call_event.c: In function 'rxrpc_process_call':
../net/rxrpc/call_event.c:879:58: warning: 'error' may be used uninitialized in this function [-Wmaybe-uninitialized]
    _debug("post net error %d", error);
                                                          ^
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Use call->peer rather than call->conn->params.peer as call->conn may become
NULL.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add a trace event for debuging rxrpc_call struct usage.
Signed-off-by: NDavid Howells <dhowells@redhat.com>