Incorporated review comments from Ben Hutchings.

Change details:
	- Implement ethtool flash_device() entry point to write the
	  firmware image to the flash firmware partition.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
	- The patch adds flash sub-module to the bna driver.
	- Added ethtool set_eeprom() and get_eeprom() entry points to
	  support flash partition read/write operations.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Rx queue size is changed, queues are torn down and setup with the new queue
size. During this operation, clear promiscuous mode and restore the original
VLAN filter.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sk_buff unmap_array grows greater than 65536 (x2) with Tx ring of 65536.
Reducing TXQ depth and safe(max) acking of Tx events to 32768 (same as Rx).
Add defines for TX and RX queue depths.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Add tx_skb counters and NAPI debug counters to ethtool stats.
 - Add rlb stats strings to bnad_net_stats_strings{} array. rlb_stats field
   was added to struct bfi_enet_stats {} but the corresponding name structure
   array for ethtool was not initialized with right strings, even though the
   actual name structure array got expanded. This caused a NULL pointer
   violation and a crash when doing ehtool -S <if_name>.
 - Modify dim timer stop logic to make it dependent on cfg and run flags
 - While setting the ring parameter restore the rx, vlan configuration and
   set rx mode
 - Indentation fix
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
This patch contains additional structure and function definition changes
that are required to enable the new msgq/enet/txrx redesign introduced
by the previous 4 patches.
 - structure and function definition changes to header files as a result
   of Ethport, Enet, IOCEth, Tx, Rx redesign.
 - ethtool changes to use new enet function and definitions
 - Set number of Tx and Rx queues bassed on underlying hardware. Define
   separate macros for maximum and supported numbers of Tx and Rx queues
   based on underlying hardware. Take VLAN header into account for MTU
   calculation. Default to INTx mode when pci_enable_msix() fails. Set a
   bit in Rx poll routine, check and wait for that bit to be cleared in
   the cleanup routine before proceeding.
 - The TX and Rx coalesce settings are programmed in steps of 5 us. The value
   that are not divisible by 5 are rounded to the next lower number. This was
   causing the value os 1 to 4 to be rounded to 0, which is an invalid setting.
   When creating Rx and Tx object, we are currently assigning the default
   values of Rx and Tx coalescing_timeo. If these values are changed in the
   driver to a different value, the change is lost during such operations as
   MTU change. In order to avoid that, pass the configured value of
   coalescing_timeo before Rx and Tx object creation. Fix
   bnad_tx_coalescing_timeo_set() so it applies to all the Tx objects.
 - Reorg uninitialization path in case of pci_probe failure.
 - Hardware clock setup changes to pass asic generation, port modes and
   asic mode as part firmware boot parameters to firmware.
 - FW mailbox interface changes to defined asic specific mailbox interfaces.
   h/w mailbox interfaces take 8-bit FIDs and 2-bit port id for owner. Cleaned
   up mailbox definitions and usage for new and old HW. Eliminated usage of
   ASIC ID. MSI-X vector assignment and programming done by firmware. Fixed
   host offsets for CPE/RME queue registers.
 - Implement polling mechanism for FW ready to have poll mechanism replaces
   the current interrupt based FW READY method. The timer based poll routine
   in IOC will query the ioc_fwstate register to see if there is a state
   change in FW, and sends the READY event. Removed infrastructure needed to
   support mbox READY event from fw as well as IOC code.
 - Move FW init to HW init. Handle the case where PCI mapping goes away when
   IOCPF state machine is waiting for semaphore.
 - Add IOC mbox call back to client indicating that the command is sent.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Brocade driver into drivers/net/ethernet/brocade/ and make
the necessary Kconfig and Makefile changes.

CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change details:
 - This patch contains removal of get_regs support in bnad_ethtool.c. Thus
   BNA will have minimal register definitions necessary for MBOX and
   interrupt operations
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Driver cleanup as per new checkpatch v0.31
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.

For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.

All drivers compiled with make allyesconfig ion x86_64 have been
updated.

Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().

All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note: looks like bnad->conf_mutex is duplicating rtnl_lock.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kzalloc'd memory doesn't need a memset to 0.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Call netif_wake_queue() if we have freed up sufficient elements
	at the end of completion processing
	- Add netif_queue_stopped counter back to bnad_drv_stats {}
	- Get netif_queue_stopped value from stack
	- Remove BUG_ON() on value returned by pci_unmap_addr()
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
	- Removed semaphore register dump from ethtool
	- Moved netif_carrier_off() call to before calling bna_init()
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

get_stats() method incorrectly clears a global array before folding
various stats. This can break SNMP applications.

Switch to 64 bit flavor to work on a user supplied buffer, and provide
64bit counters even on 32bit arches.

Fix a bug in bnad_netdev_hwstats_fill(), for rx_fifo_errors, missing a
folding (only the last counter was taken into account)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the patch to fix the build break caused by multiple
definitions of symbols between Brocade's FC/FCOE driver(BFA)
and 10G Networking Driver(BNA).

Changes are:

1. locally used functions are made static 

2. unused functions are removed

3. using unique namespaces for the function names that must be
globally visible
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver doesn't support LRO, NTUPLE, or the RXHASH
features.  So it should not set these ethtool operations.

This also fixes the warning:

drivers/net/bna/bnad_ethtool.c:1272: warning: initialization from incompatible pointer type
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is patch 1/6 which contains linux driver source for
Brocade's BR1010/BR1020 10Gb CEE capable ethernet adapter.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>