bna: Move the Brocade driver

Moves the Brocade driver into drivers/net/ethernet/brocade/ and make
the necessary Kconfig and Makefile changes.

CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

MAINTAINERS

@@ -1576,7 +1576,7 @@ M:	Rasesh Mody <rmody@brocade.com>
 M:	Debashis Dutt <ddutt@brocade.com>
 L:	netdev@vger.kernel.org
 S:	Supported
-F:	drivers/net/bna/
+F:	drivers/net/ethernet/brocade/bna/
 
 BSG (block layer generic sg v4 driver)
 M:	FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>

drivers/net/Kconfig

@@ -1584,20 +1584,6 @@ config TEHUTI
 	help
 	  Tehuti Networks 10G Ethernet NIC
 
-config BNA
-	tristate "Brocade 1010/1020 10Gb Ethernet Driver support"
-	depends on PCI
-	---help---
-	  This driver supports Brocade 1010/1020 10Gb CEE capable Ethernet
-	  cards.
-	  To compile this driver as a module, choose M here: the module
-	  will be called bna.
-
-	  For general information and support, go to the Brocade support
-	  website at:
-
-	  <http://support.brocade.com>
-
 endif # NETDEV_10000
 
 source "drivers/net/tokenring/Kconfig"

drivers/net/Makefile

@@ -25,7 +25,6 @@ obj-$(CONFIG_TEHUTI) += tehuti.o
 obj-$(CONFIG_ENIC) += enic/
 obj-$(CONFIG_JME) += jme.o
 obj-$(CONFIG_VMXNET3) += vmxnet3/
-obj-$(CONFIG_BNA) += bna/
 
 gianfar_driver-objs := gianfar.o \
 		gianfar_ethtool.o \

drivers/net/ethernet/Kconfig

@@ -15,6 +15,7 @@ source "drivers/net/ethernet/3com/Kconfig"
 source "drivers/net/ethernet/8390/Kconfig"
 source "drivers/net/ethernet/amd/Kconfig"
 source "drivers/net/ethernet/broadcom/Kconfig"
+source "drivers/net/ethernet/brocade/Kconfig"
 source "drivers/net/ethernet/chelsio/Kconfig"
 source "drivers/net/ethernet/emulex/Kconfig"
 source "drivers/net/ethernet/intel/Kconfig"

drivers/net/ethernet/Makefile

@@ -6,6 +6,7 @@ obj-$(CONFIG_NET_VENDOR_3COM) += 3com/
 obj-$(CONFIG_NET_VENDOR_8390) += 8390/
 obj-$(CONFIG_NET_VENDOR_AMD) += amd/
 obj-$(CONFIG_NET_VENDOR_BROADCOM) += broadcom/
+obj-$(CONFIG_NET_VENDOR_BROCADE) += brocade/
 obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
 obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
 obj-$(CONFIG_NET_VENDOR_INTEL) += intel/

drivers/net/ethernet/brocade/Kconfig

+#
+# Brocade device configuration
+#
+
+config NET_VENDOR_BROCADE
+	bool "Brocade devices"
+	depends on PCI
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Brocade cards. If you say Y, you will be asked for
+	  your specific card in the following questions.
+
+if NET_VENDOR_BROCADE
+
+source "drivers/net/ethernet/brocade/bna/Kconfig"
+
+endif # NET_VENDOR_BROCADE

drivers/net/ethernet/brocade/Makefile

+#
+# Makefile for the Brocade device drivers.
+#
+
+obj-$(CONFIG_BNA) += bna/

drivers/net/ethernet/brocade/bna/Kconfig

+#
+# Brocade network device configuration
+#
+
+config BNA
+	tristate "Brocade 1010/1020 10Gb Ethernet Driver support"
+	depends on PCI
+	---help---
+	  This driver supports Brocade 1010/1020 10Gb CEE capable Ethernet
+	  cards.
+	  To compile this driver as a module, choose M here: the module
+	  will be called bna.
+
+	  For general information and support, go to the Brocade support
+	  website at:
+
+	  <http://support.brocade.com>