Factor out and export input_match_device_id() so that modules may use it.
It will be needed by joydev to blacklist accelerometers in composite
devices.
Tested-by: NRoderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.

Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.

This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7d ("i2c: designware: wait for disable/enable only
if necessary").

Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.

Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.

Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: NPaul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
                      add comment about typical poll time]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: NBastien Nocera <hadess@hadess.net>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Now that we have a platform_device_id table and multiple supported ids
we should be using MODULE_DEVICE_TABLE instead of MODULE_ALIAS.

This fixes a regression on Bay and Cherry Trail devices, where the power
button is now enumerated as an "axp221-pek" and it was impossible to
wakeup these devices from suspend since the module did not load.

Fixes: c3cc9447 ("Input: axp20x-pek - add support for AXP221 PEK")
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Currently, enabling keypad interrupts is one of the first operations
done on the keypad, even before the interrupt is requested, so there is
a small time window where the keypad can fire interrupts but the driver
is not yet ready to handle them. It's fine for level interrupts because
they will be handled anyway, but not so much for edge ones.

This commit modifies and moves the function in charge of configuring the
keypad. Enabling interrupts is now the last thing done on the keypad,
and after the interrupt has been requested by the driver.

Writing to the config register was also used to determine if the device
was indeed present on the bus or not, this has been replaced by reading
the lock/event count register to keep the same functionality.
Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The commit 78bcac7b ("Input: add support for the STMicroelectronics
FingerTip touchscreen) used the 'touchscreen_parse_properties()' helper
function in order to get the value of common properties.

But, commit 78bcac7b didn't set the capability of ABS_MT_POSITION_*
before calling touchscreen_parse_properties(). In result, the max_x and
max_y of 'struct touchscreen_properties' were not set.

Fixes: 78bcac7b ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Cc: stable@vger.kernel.org
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Step config setting for 5 wire touchscreen is incorrect for Y coordinates.
It was broken while we moved to DT. If you look close at the offending
commit bb76dc09 ("input: ti_am33x_tsc: Order of TSC wires, made
configurable"), the change was:

- STEPCONFIG_XNP | STEPCONFIG_YPN;
+ ts_dev->bit_xn | ts_dev->bit_yp;

while bit_xn = STEPCONFIG_XNN and bit_yp = STEPCONFIG_YNN. Not quite the
same.

Fixes: bb76dc09 ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Signed-off-by: NJeff Lance <j-lance1@ti.com>
[vigneshr@ti.com: Rebase to v4.14-rc1]
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NMichael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

In certain situations kernel tracking seems to be getting confused
and incorrectly reporting the slot of a contact. On example is when
the user does a three finger click or tap and then places two fingers
on the touchpad in the same area. The kernel tracking code seems to
continue to think that there are three contacts on the touchpad and
incorrectly alternates the slot of one of the contacts. The result that
is the input subsystem reports a stream of button press and release
events as the reported slot changes.

Kernel tracking was originally enabled to prevent cursor jumps, but it
is unclear how much of an issue kernel jumps actually are. This patch
simply disabled kernel tracking for now.

Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1482640Signed-off-by: NAndrew Duggan <aduggan@synaptics.com>
Tested-by: NKamil Páral <kparal@redhat.com>
Acked-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The original 20ms delay is only marginally enough delay after a block write
operation during firmware update. Let's increase the delay to ensure that
the controller finishes up storing the page to avoid failures in the
firmware updates.
Signed-off-by: NKT Liao <kt.liao@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

If FF request comes in while uinput device is going away,
uinput_request_send() will fail with -ENODEV, and uinput_request_submit()
will attempt to mark the slot as unused by calling uinput_request_done().
Unfortunately in this case we haven't initialized request->done completion
yet, and we get a crash:

[   39.402036] BUG: spinlock bad magic on CPU#1, fftest/3108
[   39.402046]  lock: 0xffff88006a93bb00, .magic: 00000000, .owner: /39, .owner_cpu: 1217155072
[   39.402055] CPU: 1 PID: 3108 Comm: fftest Tainted: G        W 4.13.0+ #15
[   39.402059] Hardware name: LENOVO 20HQS0EG02/20HQS0EG02, BIOS N1MET37W (1.22 ) 07/04/2017
[   39.402064]  0000000000000086 f0fad82f3ceaa120 ffff88006a93b9a0 ffffffff9de941bb
[   39.402077]  ffff88026df8ae00 ffff88006a93bb00 ffff88006a93b9c0 ffffffff9dca62b7
[   39.402088]  ffff88006a93bb00 ffff88006a93baf8 ffff88006a93b9e0 ffffffff9dca62e7
[   39.402099] Call Trace:
[   39.402112]  [<ffffffff9de941bb>] dump_stack+0x4d/0x63
[   39.402123]  [<ffffffff9dca62b7>] spin_dump+0x97/0x9c
[   39.402130]  [<ffffffff9dca62e7>] spin_bug+0x2b/0x2d
[   39.402138]  [<ffffffff9dca6373>] do_raw_spin_lock+0x28/0xfd
[   39.402147]  [<ffffffff9e3055cd>] _raw_spin_lock_irqsave+0x19/0x1f
[   39.402154]  [<ffffffff9dca05b7>] complete+0x1d/0x48
[   39.402162]  [<ffffffffc04f30af>] 0xffffffffc04f30af
[   39.402167]  [<ffffffffc04f468c>] 0xffffffffc04f468c
[   39.402177]  [<ffffffff9dd59c16>] ? __slab_free+0x22f/0x359
[   39.402184]  [<ffffffff9dcc13e9>] ? tk_clock_read+0xc/0xe
[   39.402189]  [<ffffffffc04f471f>] 0xffffffffc04f471f
[   39.402195]  [<ffffffff9dc9ffe5>] ? __wake_up+0x44/0x4b
[   39.402200]  [<ffffffffc04f3240>] ? 0xffffffffc04f3240
[   39.402207]  [<ffffffff9e0f57f3>] erase_effect+0xa1/0xd2
[   39.402214]  [<ffffffff9e0f58c6>] input_ff_flush+0x43/0x5c
[   39.402219]  [<ffffffffc04f32ad>] 0xffffffffc04f32ad
[   39.402227]  [<ffffffff9e0f174f>] input_flush_device+0x3d/0x51
[   39.402234]  [<ffffffff9e0f69ae>] evdev_flush+0x49/0x5c
[   39.402243]  [<ffffffff9dd62d6e>] filp_close+0x3f/0x65
[   39.402253]  [<ffffffff9dd7dcf7>] put_files_struct+0x66/0xc1
[   39.402261]  [<ffffffff9dd7ddeb>] exit_files+0x47/0x4e
[   39.402270]  [<ffffffff9dc6b329>] do_exit+0x483/0x969
[   39.402278]  [<ffffffff9dc73211>] ? recalc_sigpending_tsk+0x3d/0x44
[   39.402285]  [<ffffffff9dc6c7a2>] do_group_exit+0x42/0xb0
[   39.402293]  [<ffffffff9dc767e1>] get_signal+0x58d/0x5bf
[   39.402300]  [<ffffffff9dc03701>] do_signal+0x37/0x53e
[   39.402307]  [<ffffffff9e0f8401>] ? evdev_ioctl_handler+0xac8/0xb04
[   39.402314]  [<ffffffff9e0f8464>] ? evdev_ioctl+0x10/0x12
[   39.402321]  [<ffffffff9dd74cfa>] ? do_vfs_ioctl+0x42e/0x501
[   39.402328]  [<ffffffff9dc0170e>] prepare_exit_to_usermode+0x66/0x90
[   39.402333]  [<ffffffff9dc0181b>] syscall_return_slowpath+0xe3/0xec
[   39.402339]  [<ffffffff9e305b7b>] int_ret_from_sys_call+0x25/0x8f

While we could solve this by simply initializing the completion earlier, we
are better off rearranging the code a bit so we avoid calling complete() on
requests that we did not send out. This patch consolidates marking request
slots as free in one place (in uinput_request_submit(), the same place
where we acquire them) and having everyone else simply signal completion
of the requests.

Fixes: 00ce756c ("Input: uinput - mark failed submission requests as free")
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Normally, when input device supporting force feedback effects is being
destroyed, we try to "flush" currently playing effects, so that the
physical device does not continue vibrating (or executing other effects).
Unfortunately this does not work well for uinput as flushing of the effects
deadlocks with the destroy action:

- if device is being destroyed because the file descriptor is being closed,
  then there is noone to even service FF requests;

- if device is being destroyed because userspace sent UI_DEV_DESTROY,
  while theoretically it could be possible to service FF requests,
  userspace is unlikely to do so (they'd need to make sure FF handling
  happens on a separate thread) even if kernel solves the issue with FF
  ioctls deadlocking with UI_DEV_DESTROY ioctl on udev->mutex.

To avoid lockups like the one below, let's install a custom input device
flush handler, and avoid trying to flush force feedback effects when we
destroying the device, and instead rely on uinput to shut off the device
properly.

NMI watchdog: Watchdog detected hard LOCKUP on cpu 3
...
 <<EOE>>  [<ffffffff817a0307>] _raw_spin_lock_irqsave+0x37/0x40
 [<ffffffff810e633d>] complete+0x1d/0x50
 [<ffffffffa00ba08c>] uinput_request_done+0x3c/0x40 [uinput]
 [<ffffffffa00ba587>] uinput_request_submit.part.7+0x47/0xb0 [uinput]
 [<ffffffffa00bb62b>] uinput_dev_erase_effect+0x5b/0x76 [uinput]
 [<ffffffff815d91ad>] erase_effect+0xad/0xf0
 [<ffffffff815d929d>] flush_effects+0x4d/0x90
 [<ffffffff815d4cc0>] input_flush_device+0x40/0x60
 [<ffffffff815daf1c>] evdev_cleanup+0xac/0xc0
 [<ffffffff815daf5b>] evdev_disconnect+0x2b/0x60
 [<ffffffff815d74ac>] __input_unregister_device+0xac/0x150
 [<ffffffff815d75f7>] input_unregister_device+0x47/0x70
 [<ffffffffa00bac45>] uinput_destroy_device+0xb5/0xc0 [uinput]
 [<ffffffffa00bb2de>] uinput_ioctl_handler.isra.9+0x65e/0x740 [uinput]
 [<ffffffff811231ab>] ? do_futex+0x12b/0xad0
 [<ffffffffa00bb3f8>] uinput_ioctl+0x18/0x20 [uinput]
 [<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
 [<ffffffff81337553>] ? security_file_ioctl+0x43/0x60
 [<ffffffff812414a9>] SyS_ioctl+0x79/0x90
 [<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
Reported-by: NRodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Reported-by: NClément VUCHENER <clement.vuchener@gmail.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=193741Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare second round of input updates for 4.14 merge window.

Similar to other Gigabyte laptops, the touchpad on P57 requires a
keyboard reset to detect Elantech touchpad correctly.

BugLink: https://bugs.launchpad.net/bugs/1594214Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

We should only see devices with interrupt endpoints. Ignore any other
endpoints that we find, so we don't send try to send them interrupt URBs
and trigger a WARN down in the USB stack.
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Tested-by: NAndrey Konovalov <andreyknvl@google.com>
Cc: <stable@vger.kernel.org> # c01b5e74 Input: xpad - don't depend on endpoint order
Signed-off-by: NCameron Gutman <aicommander@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of stopping the touchscreen we were starting it in suspend, and
disabling it in resume.

Fixes: c899afed ("Input: ucb1400_ts - convert to threaded IRQ")
Reported-by: NAnton Volkov <avolkov@ispras.ru>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

reg_addr->reg_report_rate is supposed to exist in M06, not M09.

The driver is written to skip avoids access to non-existing registers
when the register address is NO_REGISTER (0xff). But
reg_addr->reg_report_rate is initialized to 0x00 by devm_kzalloc() (in
edt_ft5x06_ts_probe()) and not changed thereafter. So the checks do
not work and an access to register 0x00 is done.

Fix by setting reg_addr->reg_report_rate to NO_REGISTER.

Also fix the only place where reg_report_rate is checked against zero
instead of NO_REGISTER.
Signed-off-by: NLuca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Don't populate the arrays debounce_packet on the stack, instead make
them static.  Makes the object code smaller by over 870 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  30553	   9152	      0	  39705	   9b19	drivers/input/mouse/elantech.o

After:
   text	   data	    bss	    dec	    hex	filename
  29521	   9312	      0	  38833	   97b1	drivers/input/mouse/elantech.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Don't populate the const array header on the stack, instead make it
static.  Makes the object code smaller by over 180 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
   6003	   1536	      0	   7539	   1d73	surface3_spi.o

After:
   text	   data	    bss	    dec	    hex	filename
   5726	   1632	      0	   7358	   1cbe	surface3_spi.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

On some x86 tablets with a Goodix touchscreen, the Windows logo on the
front is a capacitive home button. Touching this button results in a touch
with bit 4 of the first byte set, while only the lower 4 bits (0-3) are
used to indicate the number of touches.

Report a KEY_LEFTMETA press when this happens.

Note that the hardware might support more than one button, in which
case the "id" byte of coor_data would identify the button in question.
This is not implemented as we don't have access to hardware with
multiple buttons.
Signed-off-by: NSergei A. Trusov <sergei.a.trusov@ya.ru>
Acked-by: NBastien Nocera <hadess@hadess.net>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Provide a simple driver for PWM controllable vibrators.
It will be used by Motorola Droid 4.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Don't populate the array seq on the stack, instead make it static.
Makes the object code smaller by over 170 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  13227	   3232	      0	  16459	   404b	drivers/input/joystick/adi.o

After:
   text	   data	    bss	    dec	    hex	filename
  12957	   3328	      0	  16285	   3f9d	drivers/input/joystick/adi.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare input updates for 4.14 merge window.

Don't populate the array seq on the stack, instead make it static.
Makes the object code smaller by over 1100 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
   6152	   1216	     64	   7432	   1d08	drivers/input/mouse/byd.o

After:
   text	   data	    bss	    dec	    hex	filename
   4974	   1280	     64	   6318	   18ae	drivers/input/mouse/byd.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Fix multiline comments style not to be reported by checkpatch.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The PowerA gamepad initialization quirk worked with the PowerA
wired gamepad I had around (0x24c6:0x543a), but a user reported [0]
that it didn't work for him, even though our gamepads shared the
same vendor and product IDs.

When I initially implemented the PowerA quirk, I wanted to avoid
actually triggering the rumble action during init. My tests showed
that my gamepad would work correctly even if it received a rumble
of 0 intensity, so that's what I went with.

Unfortunately, this apparently isn't true for all models (perhaps
a firmware difference?). This non-working gamepad seems to require
the real magic rumble packet that the Microsoft driver sends, which
actually vibrates the gamepad. To counteract this effect, I still
send the old zero-rumble PowerA quirk packet which cancels the
rumble effect before the motors can spin up enough to vibrate.

[0]: https://github.com/paroj/xpad/issues/48#issuecomment-313904867Reported-by: NKyle Beauchamp <kyleabeauchamp@gmail.com>
Tested-by: NKyle Beauchamp <kyleabeauchamp@gmail.com>
Fixes: 81093c98 ("Input: xpad - support some quirky Xbox One pads")
Cc: stable@vger.kernel.org # v4.12
Signed-off-by: NCameron Gutman <aicommander@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

User-modified input settings no longer survive a suspend/resume cycle.
Starting with 4.12, the touchpad is reinitialized on every reconnect
because the hardware appears to be different. This can be reproduced
by running the following as root:

    echo -n reconnect >/sys/devices/platform/i8042/serio1/drvctl

A line like the following will show up in dmesg:

    [30378.295794] psmouse serio1: synaptics: hardware appears to be
                   different: id(149271-149271), model(114865-114865),
                   caps(d047b3-d047b1), ext(b40000-b40000).

Note the single bit difference in caps: bit 1 (SYN_CAP_MULTIFINGER).

This happens because we modify our stored copy of the device info
capabilities when we enable advanced gesture mode but this change is
not reflected in the actual hardware capabilities.

It worked in the past because synaptics_query_hardware used to modify
the stored synaptics_device_info struct instead of filling in a new
one, as it does now.

Fix it by no longer faking the SYN_CAP_MULTIFINGER bit when setting
advanced gesture mode. This necessitated a small refactoring.

Fixes: 6c53694f ("Input: synaptics - split device info into a separate structure")
Signed-off-by: NAnthony Martin <ality@pbrane.org>
Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This driver provides PS/2 serio bus support by implementing bit banging
with the GPIO API. The GPIO pins, data and clock, can be configured with
a node in the device tree or by generic device properties (GDP).

Writing to a device is supported as well, though it is possible timings
can not be halt as they are tough and difficult to reach with bit banging.
Therefore it can be configured (also in DT and GDP) whether the serio
write function should be available for clients.

This driver is for development purposes and not recommended for productive
use. However, this driver can be useful e.g. when no USB port is available
or using old peripherals is desired as PS/2 controller chips getting rare.

This driver was tested on bcm2825 and on Kirin 960 and it worked well
together with the atkbd and psmouse driver.
Signed-off-by: NDanilo Krummrich <danilokrummrich@dk-develop.de>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Long pressed key could not show right in XEN vncviewer after tigervnc
client changed the way how to send repeat keys, from "Down Up Down Up
..." to "Down Down ... Up". This will report autorepeat to input by
checking if same key being pressed, and let handler process it finally.
Signed-off-by: NLiang Yan <lyan@suse.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Fixed the issue that two finger scroll does not work correctly
on V8 protocol. The cause is that V8 protocol X-coordinate decode
is wrong at SS4 PLUS device. I added SS4 PLUS X decode definition.

Mote notes:
the problem manifests itself by the commit e7348396 ("Input: ALPS
- fix V8+ protocol handling (73 03 28)"), where a fix for the V8+
protocol was applied.  Although the culprit must have been present
beforehand, the two-finger scroll worked casually even with the
wrongly reported values by some reason.  It got broken by the commit
above just because it changed x_max value, and this made libinput
correctly figuring the MT events.  Since the X coord is reported as
falsely doubled, the events on the right-half side go outside the
boundary, thus they are no longer handled.  This resulted as a broken
two-finger scroll.

One finger event is decoded differently, and it didn't suffer from
this problem.  The problem was only about MT events. --tiwai

Fixes: e7348396 ("Input: ALPS - fix V8+ protocol handling (73 03 28)")
Signed-off-by: NMasaki Ota <masaki.ota@jp.alps.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Tested-by: NPaul Donohue <linux-kernel@PaulSD.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Provide support for controlling reset pin. If this is not driven
correctly the device will be held in reset and will not respond.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Switch mxt_data and interrupt to resource managed allocation methods,
which cleans up the driver slightly and prepares for adding
reset GPIO support.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The Dell XPS13 9365 has an INT33D2 ACPI node with no GPIOs, causing
the following error in dmesg:

[    7.172275] soc_button_array: probe of INT33D2:00 failed with error -2

This commit silences this, by returning -ENODEV when there are no GPIOs.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196679Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>