On the imx23-olinuxino board GPIO2_1 is connected to the LED and GPIO0_17
is the USB PHY reset.

So make the IOMUX assignment properly.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

imx23-olinuxino board has spi pins exposed on external connector.
This patch add spi support.
Signed-off-by: NFadil Berisha <f.koliqi@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:

leds-gpio leds.5: pins are not configured from the driver
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The initial state of the gpio led can be set directly in "gpios" node.

Hence, linux,default-trigger can be removed.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add USB host support.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Olinuxino has a LED connected to MX23_PAD_SSP1_DETECT__GPIO_2_1 pin.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add AUART0 support.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

mx23-olinuxino is a low cost board designed by Olimex.

It has the following features:

- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output

More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.htmlSigned-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lily <brian@crystalfontz.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It adds initial device tree support for imx23-evk board, and only
serial console is enabled.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NMarek Vasut <marex@denx.de>

This patch includes basic dt support which can boot via nfs rootfs.
Signed-off-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NMarek Vasut <marex@denx.de>