This patch replaces instances where a return code from i2c operations
were checked against a list of error codes with a much simpler
if ( status != 0 ) check.

Some whitespace cleanups included.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes sure that the SW lock is released after all i2c
operations complete in the retry code path.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.

Based on original patch from Aurélien Guillaume <footplus@gmail.com>

CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removes the autoneg parameter from the setup_link_speed functions.  These
functions do nothing with this parameter.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for 1G Fiber PHY modules (SFP+ modules). This support
comes along side support for 1G Copper PHY modules, but uses a different PHY
type (ixgbe_sfp_type_1g_sx_core).
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for I2C clock stretching which is required per
SFF-8636.  Customers with passive DA cables implement clock stretching
would fail without this patch.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

New year so bump the copyright date.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X520 family of network devices, with the 82599 chip, support a
small number of Intel-verified SFP+ modules on their NICs.  To maintain
stability and quality, the current devices restrict untested 3rd party
SFP+ modules.

This patch introduces a module parameter for ixgbe to allow these untested
modules at the user's peril.  It also includes a warning to the syslog
alerting users that the modules aren't supported, and results may
vary.

CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I2C access is timing critical. Always do a write flush after writing
to the I2CCTL register.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

DaveM said:
   Please, this kind of stuff rots forever and not using bool properly
   drives me crazy.

Joe Perches <joe@perches.com> gave me the spatch script:

	@@
	bool b;
	@@
	-b = 0
	+b = false
	@@
	bool b;
	@@
	-b = 1
	+b = true

I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since ixgbe_raise_i2c_clk() can never return anything else than 0
this patch removes it's return value and all checks for it.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clear the data field in ixgbe_read_i2c_byte_generic so it does not
accumulate 1 bit using the same variable multiple times.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();

which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();

explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device.  If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change remaining direct calls to function pointers.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

100H is not supported on this HW, but the bit is set on the PHY.
This can result in link at 100F when advertising only 1000F.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

100H is not supported on this HW, but the bit is set on the PHY.
This can result in link at 100F when advertising only 1000F.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since msleep might not sleep for the desired amount when less
than 20ms use usleep_range.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

This change updates the PHY setup code to support 100Mbps capable PHYs
as well as 10G and 1Gbps.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up several situations in which we were either stepping
over possible errors, or calling initialization routines multiple times.
Also includes whitespace fixes where applicable.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Updating the copyrights for 2011 as well as make the ixgbe_copyright string
a constant.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X540 devices grabs semaphores differently than 82599 and 82598
devices do.  They do however also grab them in allot of the same
functions.  So I'm adding a new MAC operation function pointer to
allow us to use the correct function based on our MAC type.  I'm also
changing all the semaphore calls to use this new function pointer.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The I2C interface was not being correctly locked down per port.  As such
this can lead to race conditions that can cause issues.  This patch cleans
up the handling to make certain we are not experiencing racy I2C access.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some PHYs require that we poll the reset bit and wait for it to clear
before continuing initialization.  As such we should add this check to the
end of the ixgbe_reset_phy_generic routine.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up several issues in ixgbe_identify_sfp_module_generic
including whitespace, redundant code, I2C EEPROM reads without exception
handling, and an if/elseif/else without braces.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The existing PHY ID for X540 was from early production hardware and
is no longer correct.  This patch corrects that.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adds the new x540.c file and Aquantia 1202 PHY for X540 support.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The new MAC type X540 shares much of the same functionality of
some silicon specific functions.  To reduce duplicate code,
made these functions generic.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for 1G SFP+ PHY's to 82599.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These comments were forgotten in the initial patch to add this
functionality.  This patch corrects that.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support of active DA cables.  This is
renaming and adding some PHY type enumerations.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Includes one minor indentation fix to placate checkpatch.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.

- mdio45_probe call was always failing due to mdio.prtad not being
set.  The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0.  This will allow us to set the phy_id
and phy.type correctly now.

- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.

- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82599 supports multispeed fiber optical modules (10Gbps/1Gbps).  Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner.  This will restart the autotry
mechanism to get link into a known state.  The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in.  This patch corrects that by:

ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.

ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.

ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected.  Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.

Other functions were updated to allow correct logging.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SFF specification for Direct Attach cable detection has now been
ratified.  Previously, DA cable detect was looking at the Twinaxial bit in
byte 9 of the SFP+ EEPROM.  The spec now defines active and passive DA
cables in byte 8 of the SFP+ EEPROM.  This patch changes the cable
detection for both 82598 and 82599 SFP+ adapters to conform to the new
spec.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>