While receiving unsupported rate frame rx state machine
gets into a state 0xb and if phy_restart happens in that
state, BB would go hang. If RXSM is in 0xb state after
first bb panic, ensure to disable the phy_restart.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Times They Are a-Changin'.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9285 belongs to diversity group 0 and AR9485 belongs to diversity
group 2. Based on the diversity group we configure certain antenna
diversity paramaters such as lna1_lna2_delta and fast diversity
bias values. For AR9485 we have some gain table parameter which
selects the gain table 0/1 for main and alternate antenna

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

define few registers and macros to configure/enable Antenna diversity
parameters in AR9485

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

this is necessary to support Antenna diversity and combining in new chip
sets such as AR9485, previously Antenna diversity support is available
only in AR9285

Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when aggregation protection mode is enabled the hardware needs
to send RTS/CTS for each HT frame. Currently its disabled so
remove the unused call backs.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should protect hw_pll handler with power save wrappers and
also modularize hw_pll handler properly for better readability.

Also add a debug message to track chip resets on pll hang condition.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a bool in ath9k_platform_data to pass AHB clock speed information.
Driver needs this to configure PLL on some SOCs.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This struct is not used in any common code, and moving it out of
the ath header makes it easier to add more driver specific ops.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function is nowhere used.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This does not seems to be used anywhere so remove it.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not used anywhere
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not used anywhere and seems pointless
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is only used in one place, and the device id check that it's based on
can be moved there as well.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The EEPROM contains a field that can restrict the number of hardware queues,
however this is not only useless (all the known chips contain the same
number of hardware queues), but also potentially dangerous in case of a
misprogrammed EEPROM (could trigger driver crashes), so let's just ignore
it completely.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big,
so they shouldn't be inlined at every single callsite, especially since they
can easily be turned into real functions.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this change, loading the address to a register read/write function
costs only one pointer dereference instead of two. On MIPS this reduces
ath9k_hw binary size from 326k down to 321k.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.

To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some devices control antenna settings or other things through GPIO pins
of the wireless interface. Add a debugfs interface for changing those
and keeping them set across card resets.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fine-tuning register write operation and avoid unnecessay
delays for ath9k_htc driver, saves hw reset time which
improves scanning time and also solves one of the following
scenario.

Sometimes the ACK is sent by STA for assoc response is not
seen at AP side. So the AP continues to send retry assoc
responses. At the STA side, since the assoc response was
already forwarded to mac80211, it proceeded to channel change
which in turns does chip reset.

In most of the cases the chip reset was completed before
max retries are reached at AP side. Hence STA can able to ACK
the retried frames again. But in clear environment these retries
are completed within shortspan of time.

Since ath9k_htc consumes more time for hw reset, this latency
is causing dissociation by AP due to max reties are reached.
This issue was originally reported with Cisco Aironet 1250 AP
in HT40 mode in noise free environment.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a function to observe the delta VC of BB_PLL.
For a good chip, the sqsum_dvc is below 2000.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.

Cc: stable@kernel.org
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This would decrease latency in reading bulk registers.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.

For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the drop in Tx power for a particular mcs rate exceeds
the paprd scale factor, paprd may not work properly. Disable
paprd for any such rates.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helper can be used in multiple places. Also make
it inline returning u8.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>