We currently do not perform accounting in the driver and thus can't
reject routes before resources are exceeded.

However, in order to make users aware of the fact that routes are no
longer offloaded we can return an error for routes configured after the
abort mechanism was triggered.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 9776d325 ("net: Move call_fib_rule_notifiers up in
fib_nl_newrule") it is possible to forbid the installation of
unsupported FIB rules.

Have mlxsw return an error for non-default FIB rules in addition to the
existing extack message.

Example:
# ip rule add from 198.51.100.1 table 10
Error: mlxsw_spectrum: FIB rules not supported.

Note that offload is only aborted when non-default FIB rules are already
installed and merely replayed during module initialization.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add device id's 0x5019, 0x501a and 0x501b for T5
cards.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the quest to remove all stack VLAs from the kernel[1], this switches
the "status" stack buffer to use the existing small (8) upper bound on
how many queues can be checked for DMA, and adds a sanity-check just to
make sure it doesn't operate under pathological conditions.

[1] http://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.comSigned-off-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIC firmware does not support disabling rx vlan offload, but the VF driver
incorrectly indicates that it is supported.  The PF driver already does the
correct indication by clearing the NETIF_F_HW_VLAN_CTAG_RX bit in its
netdev->hw_features.  So just do the same thing in the VF.
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: NPrasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because the current statistics for size 8192~12287 are only valid for GE,
the ranges of 8192~9216 and 9217~12287 are valid only for LGE/CGE, and are
always 0 for GE interfaces. it is easy to cause confusion when viewing the
packet statistics using the command ethtool -S.

This patch removes the 8192~12287 range of packet statistics and uses the
8192~9216 and 9217~12287 ranges for statistics. This change depends on the
firmware upgrade.
Signed-off-by: NXi Wang <wangxi11@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two level of vlan tables in hardware, one is port vlan
which is shared by all functions, the other one is function
vlan table, each function has it's own function vlan table.
Currently, PF sets the port vlan table, and vf sets the function
vlan table, which will cause packet lost problem.

This patch fixes this problem by setting both vlan table, and
use hdev->vlan_table to manage thet port vlan table.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If head has invlid value then a dead loop can be triggered in
hclge_cmd_csq_clean. This patch adds sanity check for this case.

Fixes: 68c0a5c7 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd
Interface Support")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a check to support autoneg(ethtool -A) only when PHY
is attached with the port.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility
Layer) Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When phy exists, phy_addr must less than PHY_MAX_ADDR.
If not, hclge_mac_mdio_config should return error.
And for fiber(phy_addr=0xff), it does not need hclge_mac_mdio_config.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes some of the missed error legs in the initialization
function of the ae device. This might cause leaks in case of failure.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer
Support")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the handling of the check when number of vports
are detected to be more than available TPQs. Current handling causes
an out of bounds access in hclge_map_tqp().

Fixes: 7df7dad6 ("net: hns3: Refactor the mapping of tqp to vport")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the function being used to fetch L4
protocol outer header. Mistakenly skb_inner_transport_header
API was being used earlier.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mac supports DCB, but is in GE mode, it does not support
querying pfc stats, firmware returns error when trying to
query the pfc stats. this creates a lot of noise in the kernel
log when it prints the error log.

This patch fixes it by removing the error log, because it already
return the error to the user space, so the user should be aware of
the error.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The intention is to get notified of process failures as soon
as possible, before a possible core dumping (which could be very long)
(e.g. in some process-manager). Coredump and exit process events
are perfect for such use cases (see 2b5faa4c "connector: Added
coredumping event to the process connector").

The problem is that for now the process-manager cannot know the parent
of a dying process using connectors. This could be useful if the
process-manager should monitor for failures only children of certain
parents, so we could filter the coredump and exit events by parent
process and/or thread ID.

Add parent pid and tgid to coredump and exit process connectors event
data.
Signed-off-by: NStefan Strogin <sstrogin@cisco.com>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the Meson-AXG SoC, the phy mode setting of PRG_ETH0 in the glue layer
is extended from bit[0] to bit[2:0].
  There is no problem if we configure it to the RGMII 1000M PHY mode,
since the register setting is coincidentally compatible with previous one,
but for the RMII 100M PHY mode, the configuration need to be changed to
value - b100.
  This patch was verified with a RTL8201F 100M ethernet PHY.
Signed-off-by: NYixun Lan <yixun.lan@amlogic.com>
Acked-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add statistics for rare TLS related errors.
Since the errors are rare we have a counter per netdev
rather then per SQ.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the TLS tx offload data path according to the
requirements of the TLS generic NIC offload infrastructure.

Special metadata ethertype is used to pass information to
the hardware.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add NETIF_F_HW_TLS_TX capability and expose tlsdev_ops to work with the
TLS generic NIC offload infrastructure.
The NETIF_F_HW_TLS_TX capability will be added in the next patch.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add routines for manipulating TLS TX offload contexts.

In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.

Add implementation for Innova TLS (FPGA-based) hardware.

These routines will be used by the TLS offload support in a later patch

mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.

In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The defines are not IPSEC specific.
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When handling mirroring to a gretap or ip6gretap netdevice in mlxsw, the
underlay address (i.e. the remote address of the tunnel) may be routed
to a bridge.

In that case, look up the resolved neighbor Ethernet address in that
bridge's FDB. Then configure the offload to direct the mirrored traffic
to that port, possibly with tagging.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to switchdev artifact can make a SPAN entry offloadable or
unoffloadable. To that end:

- Listen to SWITCHDEV_FDB_*_TO_BRIDGE notifications in addition to
  the *_TO_DEVICE ones, to catch whatever activity is sent to the
  bridge (likely by mlxsw itself).

  On each FDB notification, respin SPAN to reconcile it with the FDB
  changes.

- Also respin on switchdev port attribute changes (which currently
  covers changes to STP state of ports) and port object additions and
  removals.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since switchdev events can trigger SPAN respin, it is necessary that the
data structures are available. Register SPAN first, with a commentary on
what the dependencies are.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Publish the existing function mlxsw_sp_bridge_port_find(), and add
another service accessor mlxsw_sp_bridge_port_stp_state(). Publish both
in a new file spectrum_switchdev.h.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of duplicating the decision regarding port forwarding state made
by mlxsw_sp_port_vid_stp_set(), extract the decision-making into a new
function and reuse.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warnings regarding restricted __be32 type usage by strictly
specifying the type of the ipv4 address being printed in the dev_err
statement.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The expectation of the ops VIRTCHNL_OP_ENABLE_QUEUES and
VIRTCHNL_OP_DISABLE_QUEUES is that the queue map sent by
the VF is taken into account when enabling/disabling
queues in the VF VSI. This patch makes sure that happens.

By breaking out the individual queue set up functions so
that they can be called directly from the i40e_virtchnl_pf.c
file, only the queues as specified by the queue bit map that
accompanies the enable/disable queues ops will be handled.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When operating at 1GbE, the base incval for the PTP clock is so large
that multiplying it by numbers close to the max_adj can overflow the
u64.

Rather than attempting to limit the max_adj to a value small enough to
avoid overflow, instead calculate the incvalue adjustment based on the
40GbE incvalue, and then multiply that by the scaling factor for the
link speed.

This sacrifices a small amount of precision in the adjustment but we
avoid erratic behavior of the clock due to the overflow caused if ppb is
very near the maximum adjustment.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes at least 2 issues I have found with the UDP tunnel filter
configuration.

The first issue is the fact that the tunnels didn't have any sort of mutual
exclusion in place to prevent an update from racing with a user request to
add/remove a port. As such you could request to add and remove a port
before the port update code had a chance to respond which would result in a
very confusing result. To address it I have added 2 changes. First I added
the RTNL mutex wrapper around our updating of the pending, port, and
filter_index bits. Second I added logic so that we cannot use a port that
has a pending deletion since we need to free the space in hardware before
we can allow software to reuse it.

The second issue addressed is the fact that we were not recording the
actual filter index provided to us by the admin queue. As a result we were
deleting filters that were not associated with the actual filter we wanted
to delete. To fix that I added a filter_index member to the UDP port
tracking structure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the problem where each MTU change turns TSO,
GSO and GRO on from off state.

Now when TSO, GSO or GRO is turned off, MTU change does not
turn them on.
Signed-off-by: NPaweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The advertising 10G LR mode should be possible to set
but in the function i40e_set_link_ksettings() check for this
is missed. This patch adds check for 10000baseLR_Full
flag for 10G modes.
Signed-off-by: NJakub Pawlak <jakub.pawlak@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previous method for reading LLDP config was based on hard-coded
offsets. It happened to work, because of structured architecture of
the NVM memory. In the new approach, known as FLAT, we need to
calculate the absolute address, instead of using relative values.
Needed defines for memory location were added.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent versions of the Linux kernel now warn about incorrect parameter
definitions for function comments. Fix up several function comments to
correctly reflect the current function arguments. This cleans up the
warnings and helps ensure our documentation is accurate.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

use helper __skb_put_zero to replace the pattern of __skb_put() && memset()
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i40evf_add_vlan() is never called in atomic context.

i40evf_add_vlan() is only called by i40evf_vlan_rx_add_vid(),
which is only set as ".ndo_vlan_rx_add_vid" in struct net_device_ops.
".ndo_vlan_rx_add_vid" is not called in atomic context.

Despite never getting called from atomic context,
i40evf_add_vlan() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.

This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The chip-specific init code includes quite some calls which are
identical for all chips. So move these calls to tp->hw_start().

In addition move rtl_set_rx_max_size() a little to make sure it's
defined before it's used. Unfortunately the diff generated by git
is a little bit hard to read.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__dev_open() calls the ndo_set_rx_mode callback anyway, so we don't
have to do it here too.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently done:
- if mac_version in (01, 02, 03, 04)
	RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
- if mac_version in (01, 02, 03, 04)
	rtl_set_rx_tx_config_registers(tp);
- if mac_version not in (01, 02, 03, 04)
	RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
	rtl_set_rx_tx_config_registers(tp);

So we do exactly the same independent of chip version and can simplify
the code.

In addition remove the call to rtl_init_rxcfg(), it's called in
rtl_init_one() already and the set bits are never touched later.
rtl_init_8168/8101 don't include this call either.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both quirk masks are the same, so we can merge them. The quirk mask
includes most bits so it's actually easier to define a mask with
the bits to keep.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>