BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.

For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15

AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page

Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6

Just add basic support for the moment, the following updates are needed:
  i)	Ethernet - depends on SoC dts fixes
  ii)	USB Client (USB2) - depends on GPIO extcon
  ii)	HDMI - additional driver fixes pending
  iii)	Audio - additional driver fixes pending

NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Reviewed-by: NTom Rini <trini@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for the new hardware revision of the IGEP COM MODULE. Basically,
the new revision G replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a device tree description of the DLINK DIR665 wireless access
point. The support for the 88E6171 switch will be added in a later
patch.
Signed-off-by: NClaudio Leite <leitec@staticky.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-2-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This adds a device tree for the Nomadik NHK15 development kit
board.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

DT files to enable cygnus consisting on reference designs
and cygnus core configuration.
Reviewed-by: NRay Jui <rjui@broadcom.com>
Reviewed-by: NArun Parameswaran <aparames@broadcom.com>
Tested-by: NJonathan Richardson <jonathar@broadcom.com>
Reviewed-by: NJD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: NScott Branden <sbranden@broadcom.com>

Forgotten by commit ad8c3af8 ("ARM: shmobile: r7s72100: Remove
legacy board support").
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
[horms+renesas@verge.net.au:  update for addition of r8a7794-alt.dtb]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

As a first example, add device tree and bindings for the
RealView PB1176.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Adds initial support for the HP Chromebook 11.

Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Stephan van Schaik <stephan@synkhronix.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/Signed-off-by: NMike Rapoport <mike.rapoport@gmail.com>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.
Signed-off-by: NTim Bird <tim.bird@sonymobile.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

The Meson6 SoC is produced by Amlogic inc. and it is based on 2 Cortex
A9 and an ARM Mali-400 GPU.
This patch adds two basic DTSI for the preliminary support of Meson and
Meson6 SoCs. Another DTS is also added for supporting the atv1200 board,
produced by Geniatech inc.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This allows the "make dtbs" to build the aquaris5 dtb for the Mediatek
SoC.
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add reference SAMA5D4-EK platform DT file.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add a DTS file for the Broadcom BCM963138DVT reference platform board
which leverages the bcm63138.dtsi SoC DTSi file.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

This is a Q8 format 7 inch tablet with an Allwinner A13 SoC.
It has 512MB DRAM, 4GB NAND flash, an accelerometer, camera,
RTL8188-based WiFi, and micro SD slot for external storage.

It is likely made by a subsidiary of Hanns.G (Hannstar).
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds support for the i.MX1 APF9328 from Armadeus.
This change is intended to further remove non-DT support for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add support for the Gateworks GW5520 board.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the Freescale (Motorola) i.MX1 ADS board.
This change is intended to further remove non-DT support for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The Colibri VF61 is a module which needs a carrier board to actually
run. Different carrier board have different hardware support, hence
we should reflect this in the device tree files. This patch adds the
Colibri Evaluation Board, which supports almost all peripherals
defined in the Colibri standard.

Also align the compatible naming, file splitting and file naming with
the scheme which was choosen for the Tegra based modules.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

During the conversion of boards to use DT to instantiate Distributed
Switch Architecture, nobody volunteered to test. As to be expected,
the conversion was flawed. Testers and access to hardware has now
become available, and this patch hopefully fixes the problems.

dsa,mii-bus must be a phandle to the top level mdio node, not the port
specific subnode of the mdio device.

dsa,ethernet must be a phandle to the port subnode within the ethernet
DT node, not the ethernet node.

Don't pinctrl hog the card detect gpio for mvsdio.

Rename the .dts files to make it clearer which file is for the Z0
stepping and which for the A0 or later stepping.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Cc: seugene@marvell.com
Tested-by: NEugene Sanivsky <seugene@marvell.com>
Fixes: e2eaa339: ("ARM: Kirkwood: convert rd88f6281-setup.c to DT.")
Fixes: e7c8f380: ("ARM: kirkwood: Convert mv88f6281gtw_ge switch setup to DT")
Cc: <stable@vger.kernel.org> #v3.15+
Link: https://lkml.kernel.org/r/1409592941-22244-1-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Add basic support for the IFC6540 single-board computer boards, that are
based on the APQ8084 SoC. This patch adds the initial device tree and the
neccessary nodes required for enabling the serial port and eMMC.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
[uli: reduced to minimum, added cmt, enabled scif2, split off from SoC]
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

These baseboards are equipped with the Technexion TAO35030 SOM. So
they include this dtsi. The common parts are extracted into an "common"
dtsi file. The main difference between both boards is, that the *lcd
has DSS support enabled for the LCD.

Some HEAD acoustics specific features are:

- LED handling
- Special FPGA/DSP audio driver (not included in this series)
- powerdown GPIO
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This baseboard is equipped with the Technexion TAO35030 SOM. So
includes this dtsi. Some Thunder specific features are:

- LCD panel
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Acer Chromebook 13, codenamed Big, contains an NVIDIA tegra124
processor and is similar to the Venice2 reference platform.

The keyboard, USB 2, audio, sdcard and emmc have been tested
and work on the 1366x768 models. The Full HD models haven't been
tested yet.

WiFi does not yet work, it needs at least some PMIC changes to enable
the 32k clock.

The elan trackpad is not yet functional but hopefully will be soon as
there are patches under review.

There is also an issue on reboot because the TPM isn't reset.  It will
cause the stock firmware to enter recovery mode.  This can be worked
around by an EC-reset, press the refresh and power keys at the same
time.
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The r8a7740 Armadillo800EVA DTS can now be used both for
DT Multiplatform and the legacy case. Because of that
remove the r8a7740 Armadillo800EVA DT reference DTS file.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add hip04-d01.dts & hip04.dtsi for hip04 SoC platform.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Build the r8a7740 Armadillo800EVA board DTB in case
of Multiplatform. The DT reference case will be removed
and can be ignored for now.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds support for Olimex A20-OLinuXino-LIME board.
Signed-off-by: NFUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add basic IPQ8064 SoC include device tree and support for basic booting on
the AP148 Reference board with support for UART, I2C, and SPI.
Signed-off-by: NKumar Gala <galak@codeaurora.org>

This adds support for the A20 Hummingbird:
http://www.merrii.com/en/pla_d.asp?id=171

This patch enable most on-board peripherals supported on current kernel,
such as uart, i2c, spi, pwm, ohci/ehci, gmac and mmc.
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NWills Wang <wills.wang.open@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add dts file for Hisilicon x5hd2 development kit board.
Signed-off-by: NHaifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: NJiancheng Xue <jchxue@gmail.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
[olof: Rename dts/dtsi to include hisi prefix]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add model a5 which have additional jack detection.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
[tony@atomide.com: fixed a typo for make dtbs to work]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add gta04a3 model with additional acceleromer.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch is preparation of adding more boards which have common moved
to omap3-gta04.dtsi. Other boards have only small additions to omap3-gta04a4.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a sample DTS which will allow bootup of a board populated
with the BCM7445 chip.
Signed-off-by: NMarc Carino <marc.ceeeee@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Matt Porter <mporter@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>

The Lenovo Iomega ix4-300d is a 4-Bay sata NAS with dual Gb, USB2.0 & 3.0,
powered by a Marvell Armada XP MV78230 dual core CPU.

http://shop.lenovo.com/us/en/servers/network-storage/lenovoemc/ix4-300d/Signed-off-by: NBenoit Masson <yahoo@perenite.com>
Link: https://lkml.kernel.org/r/1406503839-4662-1-git-send-email-yahoo@perenite.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>