- 20 11月, 2014 7 次提交
-
-
由 Arnd Bergmann 提交于
Merge tag 'omap-for-v3.19/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Pull "Device tree related changes for omaps" from Tony Lindgren: - Fix currently harmless but wrong sizes for various GPMC connected devices - Set up timings for several GPMC connected devices to get rid of bootloader dependencies in later patches - Enable various drivers for dra7xx - Prepare Igep boards to support new variants - Add intial support for BeagleBoard-X15 * tag 'omap-for-v3.19/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (37 commits) ARM: dts: DRA7: Add aliases for all serial ports ARM: dts: Add am57xx-beagle-x15 ARM: OMAP2+: igep00x0: Add pdata-quirks for the btwilink device. ARM: dts: omap3-igep00x0: Remove i2c2 node. ARM: dts: omap3-igep0020-rev-f: Support IGEPv2 Rev. F ARM: dts: omap3-igep0020-common: Introduce igep0020 common dtsi file. ARM: dts: omap3-igep0030-rev-g: Support IGEP COM MODULE Rev. G ARM: dts: omap3-igep0030-common: Introduce igep0030 common dtsi file. ARM: dts: omap3-igep00x0: Move outside common file the on board Wifi module. ARM: dts: omap3-igep0020: Specify IGEPv2 revision in device tree. ARM: dts: omap3-igep0030: Specify IGEP COM revision in device tree. ARM: dts: omap3-igep00x0: Move NAND configuration to a common place. ARM: dts: omap3-igep00x0: Fix UART2 pins that aren't common. ARM: dts: dra7: add labels to DWC3 nodes ARM: dts: dra72x-evm: Enable CPSW and MDIO ARM: dts: dra7-evm: Keep all VDD rails always-on ARM: dts: dra72-evm: Add MMC nodes ARM: dts: dra72-evm: Add power button node ARM: dts: dra72-evm: Provide explicit pinmux for TPS PMIC ARM: dts: dra72-evm: Add regulator information to USB2 PHYs ... Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
git://git.infradead.org/linux-mvebu由 Arnd Bergmann 提交于
Pull "mvebu DT changes for v3.19" from Jason Cooper: - mvebu - ReadyNAS 102 leds, esata - ReadyNAS 2120 esata - Add cache-unified for Aurora L2 node - Add ref clk for timer and watchdog on Armada 375 - Cleanup Armada XP pinctrl for GigE - Add RGMII pinctrl, i2c eeprom, and fix 74hc595 counter on Lenovo ix4-300d - kirkwood - Add DLink DIR665 and it's DSA configuration * tag 'mvebu-dt-3.19' of git://git.infradead.org/linux-mvebu: ARM: mvebu: armada-xp: Fix 74hc595 count for Lenovo ix4-300d ARM: mvebu: armada-xp: Add I2C eeprom on Lenovo ix4-300d ARM: mvebu: armada-xp: Add RGMII pinctrl to Lenovo ix4-300d ARM: mvebu: armada-xp: Add GE0 pinctrl settings for GMII ARM: mvebu: armada-xp: Move GE0/1 pinctrl settings for RGMII ARM: mvebu: armada-xp: Use pinctrl node alias ARM: mvebu: armada-xp: Add node alias to pinctrl and add base address ARM: mvebu: armada-xp: Consolidate pinctrl node ARM: Kirkwood: DIR665: Instantiate Distributed Switch Architecture ARM: Kirkwood: Add support for DLink DIR665 ARM: mvebu: Enable rear eSATA ports of NETGEAR ReadyNAS 2120 ARM: mvebu: Enable the reference clock for timer and watchdog on Armada 375 SoC arm: mvebu: Clarify (e)SATA ports info in NETGEAR ReadyNAS 102 .dts file arm: mvebu: Fix LED color in NETGEAR ReadyNAS 102 .dts file ARM: mvebu: Fix the Aurora L2 cache node with the required cache-unified property Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
git://github.com/hisilicon/linux-hisi由 Arnd Bergmann 提交于
Pull "ARM: DT: Hisilicon terminal SoC HiX5HD2 DT updates for 3.19" from Wei Xu: - Add reboot node, reusing syscon-reboot - Add I2C nodes Hisilicon IP - Add IR node based on Hisilicon IP - Add Watchdog node based on ARM IP - Add GPIO nodes based on ARM GPIO IP - Add SATA node based on Hisilicon IP - Add USB nodes - Add MMC nodes based on Synopsys IP - Add GMAC nodes based on Hisilicon IP * tag 'hix5hd2-dt-for-3.19' of git://github.com/hisilicon/linux-hisi: ARM: dts: hix5hd2: add reboot node ARM: dts: hix5hd2: add i2c node ARM: dts: hix5hd2: add ir node ARM: dts: hix5hd2: add wdg node ARM: dts: hix5hd2: add gpio node ARM: dts: hix5hd2: add sata node ARM: dts: hix5hd2: add usb node ARM: dts: hix5hd2: add mmc node ARM: dts: hix5hd2: add gmac node Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Arnd Bergmann 提交于
Merge tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt Pull "Third Round of Renesas ARM Based SoC DT Cleanups for v3.19" from Simon Horman: * Use keyboard as gpio-keys node name * tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: kzm9g-reference: Use keyboard as gpio-keys node name ARM: shmobile: koelsch: Use keyboard as gpio-keys node name ARM: shmobile: lager: Use keyboard as gpio-keys node name ARM: shmobile: armadillo800eva: Use keyboard as gpio-keys node name Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Arnd Bergmann 提交于
Merge tag 'renesas-dt-cleanups2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt Pull "Second Round of Renesas ARM Based SoC DT Cleanups for v3.19" from Simon Horman: * Drop console= bootargs parameter on alt * Correct scifb* naming on r8a73a4 * Drop 0x unit-address prefixes * Remove unnecessary MMC options * tag 'renesas-dt-cleanups2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: alt dts: Drop console= bootargs parameter ARM: shmobile: r8a73a4: fix scifb* naming ARM: shmobile: kzm9g-reference dts: Drop bogus 0x unit-address prefix ARM: shmobile: r8a7791 dtsi: Drop bogus 0x unit-address prefix ARM: shmobile: r8a7790 dtsi: Drop bogus 0x unit-address prefix ARM: shmobile: r8a7790 dtsi: Remove unnecessary MMC options ARM: shmobile: r8a7779 dtsi: Remove unnecessary MMC options ARM: shmobile: r8a7778 dtsi: Remove unnecessary MMC options Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Arnd Bergmann 提交于
Merge tag 'renesas-dt-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt Pull "Renesas ARM Based SoC DT Updates for v3.19" from Simon Horman: * Add Add SoC-specific SATA compatible property to r8a7779 * Enable DMA for MMCIF on r8a7791 and r8a7790 * Enable USB-PHY, HS-USB and USB3.0 on r8a7791 and r8a7790 * Enable TMU timer via DT on r8a7778 * Enable CMT timer via DT on r8a73a4 * Add MMP and {SR}GX clocks to r8a7791 and r8a7790 * Correct scifa2 clock index on r8a7740 * Add missing INTCA for irqpin on r8a7740 * tag 'renesas-dt-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (34 commits) ARM: shmobile: r8a7779 dtsi: Add SoC-specific SATA compatible property ARM: shmobile: r8a7791: Reference DMA channels in MMCIF DT node ARM: shmobile: r8a7790: Reference DMA channels in MMCIF DT nodes ARM: shmobile: r8a7791: Add MMCIF0 DT node ARM: shmobile: r8a7790: Rename mmcif node to mmc ARM: shmobile: r8a7778: Add SoC-specific TMU compatible property ARM: shmobile: r8a73a4: Add SoC-specific CMT compatible property ARM: shmobile: henninger: enable HS-USB ARM: shmobile: koelsch: enable HS-USB ARM: shmobile: r8a7791: add HS-USB device node ARM: shmobile: lager: enable HS-USB ARM: shmobile: r8a7790: add HS-USB device node ARM: shmobile: r8a7791: add USB3.0 device node ARM: shmobile: lager: enable USB3.0 ARM: shmobile: r8a7790: add USB3.0 device node ARM: shmobile: r8a7794: Add arch_timer to device tree ARM: shmobile: bockw-reference: Initialise TMU device using DT ARM: shmobile: r8a7778: Add TMU nodes ARM: shmobile: armadillo800eva dts: Enable TMU0 ARM: shmobile: r8a7740 dtsi: Add TMU0 and TMU1 device nodes ... Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
由 Arnd Bergmann 提交于
This is a base for the DT updates, merged through the arm-soc cleanup branch. Signed-off-by: NArnd Bergmann <arnd@arndb.de>
-
- 14 11月, 2014 4 次提交
-
-
由 Simon Horman 提交于
This appears to be the best match for ePAPR. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
This appears to be the best match for ePAPR. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
This appears to be the best match for ePAPR. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
This appears to be the best match for ePAPR. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 12 11月, 2014 13 次提交
-
-
由 Nishanth Menon 提交于
Add serial port aliases for consoles > 6. Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Nishanth Menon 提交于
BeagleBoard-X15 is the next generation Open Source Hardware BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15 processor. The platform features 2GB DDR3L (w/dual 32bit busses), eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G Ethernet. For more information, refer to: BeagleBoard-X15 Wiki: http://www.elinux.org/Beagleboard:BeagleBoard-X15 AM5728 is part of the Sitara product family whose additional details will be available: http://www.ti.com/lsds/ti/arm/overview.page Technical Reference Manual for AM5728 is public domain at: http://www.ti.com/lit/spruhz6 Just add basic support for the moment, the following updates are needed: i) Ethernet - depends on SoC dts fixes ii) USB Client (USB2) - depends on GPIO extcon ii) HDMI - additional driver fixes pending iii) Audio - additional driver fixes pending NOTE: AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All unused power supply balls must be supplied with the voltages specified in the Section 5.2, Recommended Operating Conditions". This implies that all unused voltage rails for AM5728 can never be switched off even if the hardware blocks inside that voltage domain is unused. Switching off these unused rails may result in stability issues on other domains and increased leakage and power-on-hour impacts. Signed-off-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NNishanth Menon <nm@ti.com> Reviewed-by: NTom Rini <trini@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
We can't suppose that the i2c2 pins are configured as I2C bus, these pins are connected to expansion connectors. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
Add support for the new hardware revision of the IGEPv2. Basically, the new revision F replaces the old Wifi module for a Wilink8 based module. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
Use the omap3-igep0020-common.dtsi file and remove repeated parts leaving the nodes that are not common between IGEPv2 hardware revisions. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
Add support for the new hardware revision of the IGEP COM MODULE. Basically, the new revision G replaces the old Wifi module for a Wilink8 based module. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
Use the omap3-igep0030-common.dtsi file and remove repeated parts leaving the nodes that are not common between IGEP COM MODULE hardware revisions. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
New IGEP boards revisions will use another Wifi module, so this patch moves the DT nodes outside the common omap3-igep.dtsi file to specific DT for every board. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
We'll introduce new hardware revisions soon. This patch is only to indicate which board revision supports this device tree file in order to avoid confusions. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
We'll introduce new hardware revisions soon. This patch is only to indicate which board revision supports this device tree file in order to avoid confusions. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
At this moment all supported boards use same NAND chip, so has more sense move the GPMC and NAND configuration to the omap3-igep.dtsi common place. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Enric Balletbo i Serra 提交于
UART2 is used to connect the processor with the bluetooth chip, these pins are not common between IGEPv2 boards and IGEP COM MODULE boards. This patch muxes the correct pins for every board and removes UART2 configuration from common omap3-igep.dtsi file. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NJavier Martinez Canillas <javier@dowhile0.org> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 11 11月, 2014 16 次提交
-
-
由 Felipe Balbi 提交于
by adding labels to DWC3 nodes, it's far easier for boards to reference them. Signed-off-by: NFelipe Balbi <balbi@ti.com> [tony@atomide.com: updated for otg 4 move to dra74x.dtsi] Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Mugunthan V N 提交于
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and sleep states and enable them in board evm dts file. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Nishanth Menon 提交于
DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All unused power supply balls must be supplied with the voltages specified in the Section 5.2, Recommended Operating Conditions". This implies that all unused voltage rails for Vayu can never be switched off even if the hardware blocks inside that voltage domain is unused. Switching off these unused rails may result in stability issues on other domains and increased leakage and power-on-hour impacts. J6eco-evm dts file already considers this, however j6evm-dts file needs to be fixed to consider this constraint of the SoC. Signed-off-by: NNishanth Menon <nm@ti.com> Acked-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Nishanth Menon 提交于
Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC. NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD support, but we dont have it yet. So, use the fact that control module of DRA7 is setup such that no matter what mode one configures it, GPIO option is always hardwired in - use GPIO mode for SDcard detection. [peter.ujfalusi@ti.com] The power line feeding the SD card is also used by other devices on the EVM. Use generic name instead of mmc2_3v3 so when other devices want to use the same regulator it will look a bit better. Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Nishanth Menon 提交于
With Commit adff5962 ("Input: introduce palmas-pwrbutton"), we can now support tps power button as a event source - This is SW7 (PB/WAKE) on the J6-evm. Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Nishanth Menon 提交于
Even thought sys_nirq1 is hardwired on the SoC for the pin, it is better to configure the pin to the required mux configuration. Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
The ldo4_reg regulator provides power to the USB1 and USB2 High Speed PHYs. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 George Cherian 提交于
Add USB data and pinctrl for USB. Signed-off-by: NGeorge Cherian <george.cherian@ti.com> Signed-off-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
The 4th USB controller instance present only on the DRA74x family of devices so move it there. Signed-off-by: NRoger Quadros <rogerq@ti.com> Acked-by: NNishanth Menon <nm@ti.com> Signed-off-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
DRA72-evm has a 256MB 16-bit wide NAND chip. Add pinmux and NAND node. The NAND chips 'Chip select' and 'Write protect' can be controlled using DIP Switch SW5. To use NAND, the switch must be configured like so: SW5.1 (NAND_SELn) = ON (LOW) SW5.9 (GPMC_WPN) = OFF (HIGH) Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NSekhar Nori <nsekhar@ti.com> Tested-by: NNishanth Menon <nm@ti.com> Acked-by: NNishanth Menon <nm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Mugunthan V N 提交于
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and sleep states and enable them in board evm dts file. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Mugunthan V N 提交于
Add CPSW and MDIO related device tree data for DRA7XX and made as status disabled. Phy-id, pinmux for active and sleep state needs to be added in board dts files and enable the CPSW device. Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Marek Belisko 提交于
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure the padconf register offset. Signed-off-by: NMarek Belisko <marek@goldelico.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Dmitry Lifshitz 提交于
Add DSS related pinmux and display data nodes required to support DVI video out on SBC-T3530, SBC-T3730 and SBC-T3517. Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il> Acked-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
Cc: devicetree@vger.kernel.org Reviewed-by: NTony Lindgren <tony@atomide.com> Tested-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
Cc: devicetree@vger.kernel.org Reviewed-by: NTony Lindgren <tony@atomide.com> Tested-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NTony Lindgren <tony@atomide.com>
-