* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
  sh: sh7785lcr: Map whole PCI address space.
  sh: Fix up DSP context save/restore.
  sh: Fix up number of on-chip DMA channels on SH7091.
  sh: update defconfigs.
  sh: Kill off broken direct-mapped cache mode.
  sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
  sh: Add a command line option for disabling I/O trapping.
  sh: Select ARCH_HIBERNATION_POSSIBLE.
  sh: migor: Fix up CEU use flags.
  input: migor_ts: add wakeup support
  rtc: rtc-sh: use set_irq_wake()
  input: sh_keysc: use enable/disable_irq_wake()
  sh: intc: set_irq_wake() support
  sh: intc: install enable, disable and shutdown callbacks
  clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
  sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
  sh: Fix up -Wformat-security whining.
  sh: ap325rxa: Add ov772x support, again.
  sh: Sanitize asm/mmu.h for assembly use.
  sh: Tidy up sh7786 pinmux table.
  ...

* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: add hardware handshake support to atmel_serial
  avr32: add RTS/CTS/CLK pin selection for the USARTs
  Add RTC support for Merisc boards
  avr32: at32ap700x: setup DMA for AC97C in the machine code
  avr32: at32ap700x: setup DMA for ABDAC in the machine code
  Add Merisc board support
  avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
  atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
  avr32: fix timing LCD parameters for EVKLCD10X boards
  avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
  avr32: configure MCI detect and write protect pins for EVKLCD10x boards
  avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
  avr32: add pin mask for 18-bit color on the LCD controller
  avr32: fix 15-bit LCDC pin mask to use MSB lines

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (714 commits)
  Staging: sxg: slicoss: Specify the license for Sahara SXG and Slicoss drivers
  Staging: serqt_usb: fix build due to proc tty changes
  Staging: serqt_usb: fix checkpatch errors
  Staging: serqt_usb: add TODO file
  Staging: serqt_usb: Lindent the code
  Staging: add USB serial Quatech driver
  staging: document that the wifi staging drivers a bit better
  Staging: echo cleanup
  Staging: BUG to BUG_ON changes
  Staging: remove some pointless conditionals before kfree_skb()
  Staging: line6: fix build error, select SND_RAWMIDI
  Staging: line6: fix checkpatch errors in variax.c
  Staging: line6: fix checkpatch errors in toneport.c
  Staging: line6: fix checkpatch errors in pcm.c
  Staging: line6: fix checkpatch errors in midibuf.c
  Staging: line6: fix checkpatch errors in midi.c
  Staging: line6: fix checkpatch errors in dumprequest.c
  Staging: line6: fix checkpatch errors in driver.c
  Staging: line6: fix checkpatch errors in audio.c
  Staging: line6: fix checkpatch errors in pod.c
  ...

* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
  tracing, net: fix net tree and tracing tree merge interaction
  tracing, powerpc: fix powerpc tree and tracing tree interaction
  ring-buffer: do not remove reader page from list on ring buffer free
  function-graph: allow unregistering twice
  trace: make argument 'mem' of trace_seq_putmem() const
  tracing: add missing 'extern' keywords to trace_output.h
  tracing: provide trace_seq_reserve()
  blktrace: print out BLK_TN_MESSAGE properly
  blktrace: extract duplidate code
  blktrace: fix memory leak when freeing struct blk_io_trace
  blktrace: fix blk_probes_ref chaos
  blktrace: make classic output more classic
  blktrace: fix off-by-one bug
  blktrace: fix the original blktrace
  blktrace: fix a race when creating blk_tree_root in debugfs
  blktrace: fix timestamp in binary output
  tracing, Text Edit Lock: cleanup
  tracing: filter fix for TRACE_EVENT_FORMAT events
  ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
  x86: kretprobe-booster interrupt emulation code fix
  ...

Fix up trivial conflicts in
 arch/parisc/include/asm/ftrace.h
 include/linux/memory.h
 kernel/extable.c
 kernel/module.c

Merge branch 'bzip2-lzma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip

* 'bzip2-lzma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
  bzip2/lzma: quiet Kconfig warning for INITRAMFS_COMPRESSION_NONE

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
  cpumask: remove cpumask allocation from idle_balance, fix
  numa, cpumask: move numa_node_id default implementation to topology.h, fix
  cpumask: remove cpumask allocation from idle_balance
  x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
  x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
  x86: microcode: cleanup
  x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
  cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
  numa, cpumask: move numa_node_id default implementation to topology.h
  cpumask: convert node_to_cpumask_map[] to cpumask_var_t
  cpumask: remove x86 cpumask_t uses.
  cpumask: use cpumask_var_t in uv_flush_tlb_others.
  cpumask: remove cpumask_t assignment from vector_allocation_domain()
  cpumask: make Xen use the new operators.
  cpumask: clean up summit's send_IPI functions
  cpumask: use new cpumask functions throughout x86
  x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
  cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
  cpumask: convert node_to_cpumask_map[] to cpumask_var_t
  x86: unify 32 and 64-bit node_to_cpumask_map
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
  module: use strstarts()
  strstarts: helper function for !strncmp(str, prefix, strlen(prefix))
  arm: allow usage of string functions in linux/string.h
  module: don't use stop_machine on module load
  module: create a request_module_nowait()
  module: include other structures in module version check
  module: remove the SHF_ALLOC flag on the __versions section.
  module: clarify the force-loading taint message.
  module: Export symbols needed for Ksplice
  Ksplice: Add functions for walking kallsyms symbols
  module: remove module_text_address()
  module: __module_address
  module: Make find_symbol return a struct kernel_symbol
  kernel/module.c: fix an unused goto label
  param: fix charp parameters set via sysfs

Fix trivial conflicts in kernel/extable.c manually.

* 'core/debugobjects' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  debugobjects: delay free of internal objects
  debugobjects: replace static objects when slab cache becomes available
  debug_objects: add boot-parameter toggle to turn object debugging off again

* 'printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  printk: correct the behavior of printk_timed_ratelimit()
  vsprintf: unify the format decoding layer for its 3 users, cleanup
  fix regression from "vsprintf: unify the format decoding layer for its 3 users"
  vsprintf: fix bug in negative value printing
  vsprintf: unify the format decoding layer for its 3 users
  vsprintf: add binary printf
  printk: introduce printk_once()

Fix trivial conflicts (printk_once vs log_buf_kexec_setup() added near
each other) in include/linux/kernel.h.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
  atmel-mci: fix sdc_reg typo
  tmio_mmc: add maintainer
  mmc: Add OpenFirmware bindings for SDHCI driver
  sdhci: Add quirk for forcing maximum block size to 2048 bytes
  sdhci: Add quirk for controllers that need IRQ re-init after reset
  sdhci: Add quirk for controllers that need small delays for PIO
  sdhci: Add set_clock callback and a quirk for nonstandard clocks
  sdhci: Add get_{max,timeout}_clock callbacks
  sdhci: Add support for hosts reporting inverted write-protect state
  sdhci: Add support for card-detection polling
  sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
  sdhci: Split card-detection IRQs management from sdhci_init()
  sdhci: Add support for bus-specific IO memory accessors
  mmc_spi: adjust for delayed data token response
  omap_hsmmc: Wait for SDBP
  omap_hsmmc: Fix MMC3 dma
  omap_hsmmc: Disable SDBP at suspend
  omap_hsmmc: Do not prefix slot name
  omap_hsmmc: Allow cover switch to cause rescan
  omap_hsmmc: Add 8-bit bus width mode support
  ...

Instead of always splitting the file offset into 32-bit 'high' and 'low'
parts, just split them into the largest natural word-size - which in C
terms is 'unsigned long'.

This allows 64-bit architectures to avoid the unnecessary 32-bit
shifting and masking for native format (while the compat interfaces will
obviously always have to do it).

This also changes the order of 'high' and 'low' to be "low first".  Why?
Because when we have it like this, the 64-bit system calls now don't use
the "pos_high" argument at all, and it makes more sense for the native
system call to simply match the user-mode prototype.

This results in a much more natural calling convention, and allows the
compiler to generate much more straightforward code.  On x86-64, we now
generate

        testq   %rcx, %rcx      # pos_l
        js      .L122   #,
        movq    %rcx, -48(%rbp) # pos_l, pos

from the C source

        loff_t pos = pos_from_hilo(pos_h, pos_l);
	...
        if (pos < 0)
                return -EINVAL;

and the 'pos_h' register isn't even touched.  It used to generate code
like

        mov     %r8d, %r8d      # pos_low, pos_low
        salq    $32, %rcx       #, tmp71
        movq    %r8, %rax       # pos_low, pos.386
        orq     %rcx, %rax      # tmp71, pos.386
        js      .L122   #,
        movq    %rax, -48(%rbp) # pos.386, pos

which isn't _that_ horrible, but it does show how the natural word size
is just a more sensible interface (same arguments will hold in the user
level glibc wrapper function, of course, so the kernel side is just half
of the equation!)

Note: in all cases the user code wrapper can again be the same. You can
just do

	#define HALF_BITS (sizeof(unsigned long)*4)
	__syscall(PWRITEV, fd, iov, count, offset, (offset >> HALF_BITS) >> HALF_BITS);

or something like that.  That way the user mode wrapper will also be
nicely passing in a zero (it won't actually have to do the shifts, the
compiler will understand what is going on) for the last argument.

And that is a good idea, even if nobody will necessarily ever care: if
we ever do move to a 128-bit lloff_t, this particular system call might
be left alone.  Of course, that will be the least of our worries if we
really ever need to care, so this may not be worth really caring about.

[ Fixed for lost 'loff_t' cast noticed by Andrew Morton ]
Acked-by: NGerd Hoffmann <kraxel@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ralf Baechle <ralf@linux-mips.org>>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PCI still doesn't work on sh7785lcr 29bit 256M map mode.

On SH7785, PCI -> SHwy address translation is not base+offset but
somewhat like base|offset (See HW Manual (rej09b0261) Fig. 13.11).
So, you can't export CS2,3,4,5 by 256M at CS2 (results CS0,1,2,3
exported, I guess).  There are two candidates.

a) 128M@CS2 + 128M@CS4
b) 512M@CS0

Attached patch is B. It maps 512M Byte at 0 independently of memory
size. It results CS0 to CS6 and perhaps some more being accessible
from PCI.

Tested on
7785lcr 29bit 128M map
7785lcr 29bit 256M map
(NOT tested on 32bit)
Signed-off-by: NTakashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.

This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: NMichael Trimarchi <michael@evidence.eu.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This accidentally regressed when the multi-IRQ changes went in,
switching SH7091 from 4 to 6 channels. Add SH7091 back in to the
4-channel dependency list.
Reported-by: NAdrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, mtrr: remove debug message
  x86: disable stack-protector for __restore_processor_state()
  x86: fix is_io_mapping_possible() build warning on i386 allnoconfig
  x86, setup: compile with -DDISABLE_BRANCH_PROFILING
  x86/dma: unify definition of pci_unmap_addr* and pci_unmap_len macros
  x86, mm: fix misuse of debug_kmap_atomic
  x86: remove duplicated code with pcpu_need_numa()
  x86,percpu: fix inverted NUMA test in setup_pcpu_remap()
  x86: signal: check sas_ss_size instead of sas_ss_flags()

Merge branch 'core-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ptrace: remove a useless goto

Merge branch 'stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  symbols, stacktrace: look up init symbols after module symbols

* 'rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: rcu_barrier VS cpu_hotplug: Ensure callbacks in dead cpu are migrated to online cpu

* 'ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  s390: remove arch specific smp_send_stop()
  panic: clean up kernel/panic.c
  panic, smp: provide smp_send_stop() wrapper on UP too
  panic: decrease oops_in_progress only after having done the panic
  generic-ipi: eliminate WARN_ON()s during oops/panic
  generic-ipi: cleanups
  generic-ipi: remove CSD_FLAG_WAIT
  generic-ipi: remove kmalloc()
  generic IPI: simplify barriers and locking

* 'locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  locking: rename trace_softirq_[enter|exit] => lockdep_softirq_[enter|exit]
  lockdep: remove duplicate CONFIG_DEBUG_LOCKDEP definitions
  lockdep: require framepointers for x86
  lockdep: remove extra "irq" string
  lockdep: fix incorrect state name

The MTRR code grew a new debug message which triggers commonly:

[   40.142276]   get_mtrr: cpu0 reg00 base=0000000000 size=0000080000 write-back
[   40.142280]   get_mtrr: cpu0 reg01 base=0000080000 size=0000040000 write-back
[   40.142284]   get_mtrr: cpu0 reg02 base=0000100000 size=0000040000 write-back
[   40.142311]   get_mtrr: cpu0 reg00 base=0000000000 size=0000080000 write-back
[   40.142314]   get_mtrr: cpu0 reg01 base=0000080000 size=0000040000 write-back
[   40.142317]   get_mtrr: cpu0 reg02 base=0000100000 size=0000040000 write-back

Remove this annoyance.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: allow private mappings of "direct_io" files
  fuse: allow kernel to access "direct_io" files

Bring the devices.txt back into some relationship with reality. Update the
documentation a bit.
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: remove compat stuff
  HID: constify arrays of struct apple_key_translation
  HID: add support for Kye/Genius Ergo 525V
  HID: Support Apple mini aluminum keyboard
  HID: support for Kensington slimblade device
  HID: DragonRise game controller force feedback driver
  HID: add support for another version of 0e8f:0003 device in hid-pl
  HID: fix race between usb_register_dev() and hiddev_open()
  HID: bring back possibility to specify vid/pid ignore on module load
  HID: make HID_DEBUG defaults consistent
  HID: autosuspend -- fix lockup of hid on reset
  HID: hid_reset_resume() needs to be defined only when CONFIG_PM is set
  HID: fix USB HID devices after STD with autosuspend
  HID: do not try to compile PM code with CONFIG_PM unset
  HID: autosuspend support for USB HID

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
  trivial: Update my email address
  trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
  trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
  trivial: Fix misspelling of "Celsius".
  trivial: remove unused variable 'path' in alloc_file()
  trivial: fix a pdlfush -> pdflush typo in comment
  trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
  trivial: wusb: Storage class should be before const qualifier
  trivial: drivers/char/bsr.c: Storage class should be before const qualifier
  trivial: h8300: Storage class should be before const qualifier
  trivial: fix where cgroup documentation is not correctly referred to
  trivial: Give the right path in Documentation example
  trivial: MTD: remove EOL from MODULE_DESCRIPTION
  trivial: Fix typo in bio_split()'s documentation
  trivial: PWM: fix of #endif comment
  trivial: fix typos/grammar errors in Kconfig texts
  trivial: Fix misspelling of firmware
  trivial: cgroups: documentation typo and spelling corrections
  trivial: Update contact info for Jochen Hein
  trivial: fix typo "resgister" -> "register"
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6: (21 commits)
  xtensa: we don't need to include asm/io.h
  xtensa: only build platform or variant if they contain a Makefile
  xtensa: make startup code discardable
  xtensa: ccount clocksource
  xtensa: remove platform rtc hooks
  xtensa: use generic sched_clock()
  xtensa: platform: s6105
  xtensa: let platform override KERNELOFFSET
  xtensa: s6000 variant
  xtensa: s6000 variant core definitions
  xtensa: variant irq set callbacks
  xtensa: variant-specific code
  xtensa: nommu support
  xtensa: add flat support
  xtensa: enforce slab alignment to maximum register width
  xtensa: cope with ram beginning at higher addresses
  xtensa: don't make bootmem bitmap larger than required
  xtensa: fix init_bootmem_node() argument order
  xtensa: use correct stack pointer for stack traces
  xtensa: beat Kconfig into shape
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: BUG to BUG_ON changes
  Btrfs: remove dead code
  Btrfs: remove dead code
  Btrfs: fix typos in comments
  Btrfs: remove unused ftrace include
  Btrfs: fix __ucmpdi2 compile bug on 32 bit builds
  Btrfs: free inode struct when btrfs_new_inode fails
  Btrfs: fix race in worker_loop
  Btrfs: add flushoncommit mount option
  Btrfs: notreelog mount option
  Btrfs: introduce btrfs_show_options
  Btrfs: rework allocation clustering
  Btrfs: Optimize locking in btrfs_next_leaf()
  Btrfs: break up btrfs_search_slot into smaller pieces
  Btrfs: kill the pinned_mutex
  Btrfs: kill the block group alloc mutex
  Btrfs: clean up find_free_extent
  Btrfs: free space cache cleanups
  Btrfs: unplug in the async bio submission threads
  Btrfs: keep processing bios for a given bdev if our proc is batching

Specify a license for the Alacritech Sahara (10Gbe) and SLICOSS (1GBE)
firmware files.
Signed-off-by: NChristopher Harrer <charrer@alacritech.com>
Signed-off-by: NMithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Just delete the proc tty usage in the driver as it's not needed and will
go away when it switches over to a usb-serial driver.  This fixes the
build error in the driver.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Clean up the code so it's at least readable now, fixing the
checkpatch errors.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds a TODO file
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Run Lindent on the code to give us someplace to work from
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for all Quatech usb to serial devices.

Based on an original driver from Quatech.

Cleaned up and forward ported by me.

It's a mess, uses it's own tty layer interface, and the coding style is
horrible.

Cc: Tim Gobeli <tgobeli@quatech.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Linux wireless developers don't want to hear anything about the
staging wireless drivers, for a wide range of miopic reasons.

The following patch, based on a patch from Johannes Berg, tries to
document this issue a bit better.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

before:
			errors	lines of code	errors/KLOC
drivers/staging/echo/	213		1701	125.2

after:
			errors	lines of code	errors/KLOC
drivers/staging/echo/	8		1685	4.7

Compile tested.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NStoyan Gaydarov <stoyboyker@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove some pointless conditionals before kfree_skb().
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

line6 needs to select SND_RAWMIDI, like many other drivers do.

ERROR: "snd_rawmidi_set_ops" [drivers/staging/line6/line6usb.ko] undefined!
ERROR: "snd_rawmidi_new" [drivers/staging/line6/line6usb.ko] undefined!
ERROR: "snd_rawmidi_transmit_peek" [drivers/staging/line6/line6usb.ko] undefined!
ERROR: "snd_rawmidi_transmit_ack" [drivers/staging/line6/line6usb.ko] undefined!
ERROR: "snd_rawmidi_receive" [drivers/staging/line6/line6usb.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Lots of warnings also fixed up.

Cc: Markus Grabner <grabner@icg.tugraz.at>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Lots of warnings also fixed up.

Cc: Markus Grabner <grabner@icg.tugraz.at>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>