Fixes a race and potential kernel panic if e.g. the worker was just
about to send a few P_RS_IS_IN_SYNC via the meta socket for checksum
based resync, while the receiver destroys the sockets in
drbd_disconnect.

To make sure no-one is using the meta socket,
it is not enough to stop the asender...
Grab the meta socket mutex before destroying it.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Depending on resync request size,
we need to account for more than one bit.

Impact: cosmetic

If SyncTarget reported correctly 100% equal checksums,
the SyncSource usually reported 12% equal checksums instead,
because it only counted requests, we typically do 32k resync requests,
and the bitmap granularity is still 4k.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Situation:
we have diverging data sets, i.e. we had a split brain somewhen,
but currently are connected, one node diskless.

Then we try to attach that disk, figure it is consistent,
but has a diverging data set, we refuse to attach.

This led to strange state changes:
22:18:35 bb drbd1: peer( Unknown -> Primary ) conn( WFReportParams -> Connected) pdsk( DUnknown -> UpToDate )
22:19:30 bb drbd1: disk( Diskless -> Attaching )
22:19:30 bb drbd1: disk( Attaching -> Negotiating )
22:19:30 bb drbd1: drbd_sync_handshake:
22:19:30 bb drbd1: self 97BF25798B9D5222:F33D1F62ADE698DD:4269796F9D027C83:AC45D8B5C3C1BF93 bits:19449 flags:0
22:19:30 bb drbd1: peer 280DFB6E125465D3:F33D1F62ADE698DC:4269796F9D027C82:AC45D8B5C3C1BF93 bits:2575806 flags:0
22:19:30 bb drbd1: uuid_compare()=100 by rule 90
22:19:30 bb drbd1: Split-Brain detected, dropping connection!
22:19:30 bb drbd1: disk( Negotiating -> Diskless )

while the other side says:
22:19:30 aa drbd1: Split-Brain detected, dropping connection!
22:19:30 aa drbd1: Disk attach process on the peer node was aborted.
22:19:30 aa drbd1: conn( Connected -> TOO_LARGE ) pdsk( Diskless -> Consistent )

This should be fixed now.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

we still don't support 4k 'physical' sectors 'natively',
but use a read-modify-write workaround.
And we even tried to use the extra page before we allocated it :(
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The bm_change semaphore is semantically a mutex. Convert it to a real
mutex.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>

This patch adds a simple description of the various block tracepoints
available in the kernel.
Signed-off-by: NWilliam Cohen <wcohen@redhat.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

- It looks incorrect to use blk_rq_map_sg with pci_map_page here about
  DMA mappings. dma_map_sg?

- better to use dma_map_page instead of pci_map_page.
  http://marc.info/?l=linux-kernel&m=126596737604808&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

merge_bvec_fn() returns bvec->bv_len on success. So we have to check
against this value. But in case of fs_optimization merge we compare
with wrong value. This patch must be included in
 b428cd6da7e6559aca69aa2e3a526037d3f20403
But accidentally i've forgot to add this in the initial patch.
To make things straight let's replace all such checks.
In fact this makes code easy to understand.
Signed-off-by: NDmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console:
  virtio: console: Use better variable names for fill_queue operation
  virtio: console: Fix type of 'len' as unsigned int

Merge branch 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
  x86, mrst: Fix whitespace breakage in apb_timer.c
  x86, mrst: Fix APB timer per cpu clockevent
  x86, mrst: Remove X86_MRST dependency on PCI_IOAPIC
  x86, olpc: Use pci subarch init for OLPC
  x86, pci: Add arch_init to x86_init abstraction
  x86, mrst: Add Kconfig dependencies for Moorestown
  x86, pci: Exclude Moorestown PCI code if CONFIG_X86_MRST=n
  x86, numaq: Make CONFIG_X86_NUMAQ depend on CONFIG_PCI
  x86, pci: Add sanity check for PCI fixed bar probing
  x86, legacy_irq: Remove duplicate vector assigment
  x86, legacy_irq: Remove left over nr_legacy_irqs
  x86, mrst: Platform clock setup code
  x86, apbt: Moorestown APB system timer driver
  x86, mrst: Add vrtc platform data setup code
  x86, mrst: Add platform timer info parsing code
  x86, mrst: Fill in PCI functions in x86_init layer
  x86, mrst: Add dummy legacy pic to platform setup
  x86/PCI: Moorestown PCI support
  x86, ioapic: Add dummy ioapic functions
  x86, ioapic: Early enable ioapic for timer irq
  ...

Fixed up semantic conflict of new clocksources due to commit
17622339 ("clocksource: add argument to resume callback").

* 'for-linus/i2c' of git://git.fluff.org/bjdooks/linux:
  i2c: Add support for Xilinx XPS IIC Bus Interface
  i2c: omap: Add support for 16-bit registers
  i2c-pnx: fix setting start/stop condition
  powerpc: doc/dts-bindings: update doc of FSL I2C bindings
  i2c-mpc: add support for the MPC512x processors from Freescale
  i2c-mpc: rename "setclock" initialization functions to "setup"
  i2c-mpc: use __devinit[data] for initialization functions and data
  i2c/imx: don't add probe function to the driver struct
  i2c: Add support for Ux500/Nomadik I2C controller

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (66 commits)
  mfd: Fix ucb1x00 build failure for collie_defconfig
  mfd: Fix lpc_sch related depends/selects, fix build error
  gpio: Fix sch_gpio warning
  gpio: add Intel SCH GPIO controller driver
  i2c: convert i2c-isch to platform_device
  mfd: Use completion interrupt for WM831x AUXADC
  mfd: Use completion interrupt for WM835x AUXADC
  mfd: Introduce remove_script function for twl4030
  mfd/mmc: SDHI Kconfig update
  mfd: sh_mobile_sdhi MMC_CAP_MMC_HIGHSPEED support
  gpiolib: Force wm831x GPIOs into GPIO mode when requested
  mfd: Add WM831x revision B support
  gpiolib: Correct debugfs display of WM831x GPIO inversion
  gpiolib: Actually set output state in wm831x_gpio_direction_output()
  tmio_mmc: Balance cell enable()/disable() calls
  tmio_mmc: Remove const from platform data V3
  tmio_mmc: Use 100ms mmc_detect_change() delay
  tmio_mmc: Add MMC_CAP_MMC_HIGHSPEED support V2
  tmio_mmc: Keep card-detect interrupts enabled
  mfd: Add twl6030 base addr for ID0, ID1, ID2
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (368 commits)
  Staging: winbond: fix up wireless api errors
  Staging: dream: camera: sk5k3e2fx: fix code style issues
  Staging: dream: camera: msm_camera: fix code style issues
  Staging: wlan-ng: More checkpatch.pl error cleanups
  Staging: wlan-ng - checkpatch.pl fixups
  Staging: comedi: comedi_fops.c: Checkpatch cleanup
  Staging: comedi: fix suspect code indent in ni_labpc.c
  Staging: comedi: fix yet another brace coding style issue in ni_labpc.c
  Staging: comedi: fix another brace coding style issues in ni_labpc.c
  Staging: comedi: fix brace coding style issue in ni_labpc.c
  Staging: comedi: poc: Adding some KERN_ facility level
  Staging: dream: camera: msm_camera: fix some code style issues
  Staging: wlan-ng: fix most of the style issues in hfa384x.h
  Staging: dream: camera: msm_camera: fix coding style issues
  Staging: comedi: fix bracing coding style and 80 character issues in ni_660x.c
  Staging: comedi: fix bracing coding style issue in ni_65xx.c
  Staging: comedi: pcmad: Checkpatch cleanups
  Staging: comedi: poc: fix coding style issues
  staging: dt3155: revert u_long to u64 usage
  Staging: comedi: drivers.c: Checkpatch cleanup
  ...

Fix kernel-doc notation in new seq-file functions and
correct spelling.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
  sh: Convert sh to use read/update_persistent_clock
  sh: Move PMB debugfs entry initialization to later stage
  sh: Fix up flush_cache_vmap() on SMP.
  sh: fix up MMU reset with variable PMB mapping sizes.
  sh: establish PMB mappings for NUMA nodes.
  sh: check for existing mappings for bolted PMB entries.
  sh: fixed virt/phys mapping helpers for PMB.
  sh: make pmb iomapping configurable.
  sh: reworked dynamic PMB mapping.
  sh: Fix up cpumask_of_pcibus() for the NUMA build.
  serial: sh-sci: Tidy up build warnings.
  sh: Fix up ctrl_read/write stragglers in migor setup.
  serial: sh-sci: Add DMA support.
  dmaengine: shdma: extend .device_terminate_all() to record partial transfer
  sh: merge sh7722 and sh7724 DMA register definitions
  sh: activate runtime PM for dmaengine on sh7722 and sh7724
  dmaengine: shdma: add runtime PM support.
  dmaengine: shdma: separate DMA headers.
  dmaengine: shdma: convert to platform device resources
  dmaengine: shdma: fix DMA error handling.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: use __ratelimit in unaligned.c
  parisc: Convert to read/update_persistent_clock
  parisc: Simplify param.h by including <asm-generic/param.h>
  parisc: drop unnecessary cast in __ldcw_align() macro
  parisc: add strict copy size checks (v2)
  parisc: remove trailing space in messages
  parisc: ditto sys_accept4
  parisc: wire up sys_recvmmsg

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: Provide generic subsystem-level callbacks
  PM / Runtime: Document power.runtime_auto and related functions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio: set pci bus master enable bit

This patch adds support for the Xilinx XPS IIC Bus Interface.

The driver uses the dynamic mode, supporting to put several
I2C messages in the FIFO to reduce the number of interrupts.

It has the same feature as ocores, it can be passed a list
of devices that will be added when the bus is probed.
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The current i2c-omap driver is set up for 32-bit registers, which
corresponds to most OMAP devices.  However, OMAP730/850 based
devices use a 16-bit register size.

This change modifies the driver to perform a runtime CPU type check
to determine the register sizes, and uses a bit shift of either 1
or 2 bits to compute the proper register sizes for all registers.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The start/stop condtions are set in different places repetedly in the i2c-pnx
driver.  Beside in i2c_pnx_start and i2c_pnx_stop the start/stop bit are also
set during the transfer of a i2c message in the master_xmit/rcv calls. This is
wrong since we can't set the start/stop condition during the transaction of a
single message any way. As a matter of fact, the driver will sometimes set both
the start and the stop bits at one time. This can be easily reproduced by
sending a simple read request like e.g
struct i2c_msg msgs[] = {
{ addr, 0, 1, buf },
{ addr, I2C_M_RD, offset, buf }
};
While processing the first message the i2c_pnx_master_xmit will set both the
start_bit and the stop_bit, which will eventually confuse the slave.

Fixed by remove setting start/stop condition from the transmit routines.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adds the MPC5121 to the list of supported devices,
enhances the doc of the "clock-frequency" property and removes
the obsolete "cell-index", "device_type" and "fsl-i2c" property.
Furthermore an example for the MPC5121 has been added.
Signed-off-by: NWolfgang Grandegger <wg@denx.de>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

As I2C interrupts must  be enabled for the MPC512x by the setup function
as well, "fsl,preserve-clocking" is handled in a slighly different way.
Also, the old settings are now reported calling dev_dbg(). For the
MPC512x the clock setup function of the MPC52xx can be re-used.
Furthermore, the Kconfig help has been updated and corrected.
Signed-off-by: NWolfgang Grandegger <wg@denx.de>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

To prepare  support for the MPC512x processors from Freescale the
"setclock" initialization functions have been renamed to "setup"
because I2C interrupts must be enabled for the MPC512x by this
function as well.
Signed-off-by: NWolfgang Grandegger <wg@denx.de>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

"__devinit[data]" has not yet been used for all initialization functions
and data. To avoid truncating lines, the struct "mpc_i2c_match_data" has
been renamed to "mpc_i2c_data", which is even the better name.
Signed-off-by: NWolfgang Grandegger <wg@denx.de>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Having a pointer to the probe function is unnecessary when using
platform_driver_probe and yields a section mismatch warning after
removing the white list entry "*driver" for
{ .data$, .data.rel$ } -> { .init.* } mismatches in modpost.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This adds support for ST-Ericsson's I2C block found
in Ux500 and Nomadik 8815 platforms.
Signed-off-by: Nsrinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Reviewed-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch fixes a build failure[1], by adding the missing semaphore.h include

References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2234322/Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.

Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We need to check for gpiochip_remove() errors.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NDenis Turischev <denis@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Convert i2c-isch to platform_device for the lpc mfd core to add it at probe
time.
Signed-off-by: NDenis Turischev <denis@compulab.co.il>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.

Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the state of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM8350 interrupt infrastructure hooked
up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

New function twl4030_remove_script(u8 flags) takes a script type as
defined in twl.h and prevents any script already loaded in that position
from running.  This is accomplished by programming SEQ_ADD_* to 0x3f,
the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags.

(Future) users of this function include OMAP board files for machines
facing a race condition between sleep and warm reset.
Signed-off-by: NMike Turquette <mturquette@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM
processors. While at it, make CONFIG_TMIO_MMC depend on
CONFIG_MFD_SH_MOBILE_SDHI.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>