Althought RTAS is instantiated when we enter the kernel, we can't actually
call into it until we know its entry point address. Currently we grab that
in rtas_initialize(), however that's quite late in the boot sequence.

To enable rtas_call() earlier, we can grab the RTAS entry etc. values while
we're scanning the flattened device tree. There's existing code to retrieve
the values from /chosen, however we don't store them there anymore, so remove
that code.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently the kernel blindly halts all the processors and calls the
ibm,suspend-me rtas call.  If the firmware is not in the correct
state, we then re-start all the processors and return.  It is much
smarter to first check the firmware state, and only if it is waiting,
call the ibm,suspend-me call.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch attempts to handle RTAS "busy" return codes in a more simple
and consistent manner.  Typical callers of RTAS shouldn't have to
manage wait times and delay calls.

This patch also changes the kernel to use msleep() rather than udelay()
when a runtime delay is necessary.  This will avoid CPU soft lockups
for extended delay conditions.
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds Kconfig entries to control the early debugging options,
currently in setup_64.c.

Doing this via Kconfig rather than #defines means you can have one source tree,
which is buildable for multiple platforms - and you can enable the correct
early debug option for each platform via .config.

I made udbg_early_init() a static inline because otherwise GCC is to daft to
optimise it away when debugging is off.

Now that we have udbg_init_rtas() we can make call_rtas_display_status* static.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

include/asm-ppc/ had #ifdef __KERNEL__ in all header files that
are not meant for use by user space, include/asm-powerpc does
not have this yet.

This patch gets us a lot closer there. There are a few cases
where I was not sure, so I left them out. I have verified
that no CONFIG_* symbols are used outside of __KERNEL__
any more and that there are no obvious compile errors when
including any of the headers in user space libraries.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This moves rtas-proc.c and rtas_flash.c into arch/powerpc/kernel, since
cell wants them as well as pseries (and chrp can use rtas-proc.c too,
at least in principle).  rtas_fw.c is gone, with its bits moved into
rtas_flash.c and rtas.c.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Cell uses the same code as pSeries for flashing the firmware
through rtas, so the implementation should not be part of
platforms/pseries.

Put it into arch/powerpc/kernel instead.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A few things change for consistency between ppc32 and ppc64:
idle functions return void; *_get_boot_time functions return
unsigned long (i.e. time_t) rather than filling in a struct rtc_time
(since that's useful to the callers and easier for pmac to
generate); *_get_rtc_time and *_set_rtc_time functions take
a struct rtc_time; irq_canonicalize is gone; nvram_sync returns
void.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This brings in the ppc64 version of prom_init.c, prom.c and btext.c
and makes them work for ppc32.  This also brings in the new calling
convention, where the first entry to the kernel (with r5 != 0) goes
to the prom_init code, which then restarts from the beginning (with
r5 == 0) after it has done its stuff.

For now this also brings in the ppc32 version of setup.c.  It also
merges lmb.h.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The pSeries_progress function is called from some places in the rtas code,
which may also be used by non-pSeries platforms.
Though pSeries is currently the only platform type that implements
display-character, the code is actually generic enough to be part of
the rtas subsystem.

I hit a bug here because the generic rtas code tried calling ppc_md.progress,
which points to an __init function on most platforms.

We could also clear the ppc_md.progress pointer when freeing the init memory
to make it more explicit that ppc_md.progress must not be called after
bootup.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The rtc rtas functions are not pSeries specific but can
also be used by BPA and other SLOF based platforms
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!