As soon as skb is pushed to hardware, it can be completed and freed, so
we should not dereference skb anymore.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to bnx2 to use byte queue limits.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rick Jones reported that TCP_CONGESTION sockopt performed on a listener
was ignored for its children sockets : right after accept() the
congestion control for new socket is the system default one.

This seems an oversight of the initial design (quoted from Stephen)

Based on prior investigation and patch from Rick.
Reported-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Yuchung Cheng <ycheng@google.com>
Tested-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer versions have been floating about, and I applied
to older variant unfortunately.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for byte queue limits and aggregates statistics
update (suggestion from Eric).
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@drr.davemloft.net>

in iSCSI SD mode to bnx2x device assigned single mac address
which is supposted to be iscsi mac. If this mode is recognized
bnx2x will disable LRO, decrease number of queues to 1 and rx ring
size to the minumum allowed by FW, this in order minimize memory use.
It will tranfer mac for iscsi usage and zero primary mac of the netdev.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN
controllers on the ISA or PC-104 bus. The I/O port or memory address
and the IRQ number must be specified via module parameters:

  insmod cc770_isa.ko port=0x310,0x380 irq=7,11

for ISA devices using I/O ports or:

  insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11

for memory mapped ISA devices.

Indirect access via address and data port is supported as well:

  insmod cc770_isa.ko port=0x310,0x380 indirect=1 irq=7,11

Furthermore, the following mode parameter can be defined:

  clk: External oscillator clock frequency (default=16000000 [16 MHz])
  cir: CPU interface register (default=0x40 [CPU_DSC])
  ocr, Bus configuration register (default=0x00)
  cor, Clockout register (default=0x00)

Note: for clk, cir, bcr and cor, the first argument re-defines the
default for all other devices, e.g.:

  insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000

is equivalent to

  insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000,24000000
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some basic regulator support for the power pins, as needed
by the ST-Ericsson Snowball platform that powers up the SMSC911
chip using an external regulator.

Platforms that use regulators and the smsc911x and have no defined
regulator for the smsc911x and claim complete regulator
constraints with no dummy regulators will need to provide it, for
example using a fixed voltage regulator. It appears that this may
affect (apart from Ux500 Snowball) possibly these archs/machines
that from some grep:s appear to define both CONFIG_SMSC911X and
CONFIG_REGULATOR:

- ARM Freescale mx3 and OMAP 2 plus, Raumfeld machines
- Blackfin
- Super-H

Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver is currently not supported on x86_64 systems because the
"isa_driver" interface is used (CONFIG_ISA=y). To overcome this
limitation, the driver is converted to a platform driver, similar to
the serial 8250 driver.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 7dc00c82 added a 'notify' parameter for vif_delete() to
distinguish whether to unregister the device.

When notify=1 means we does not need to unregister the device,
so calling unregister_netdevice_many is useless.
Signed-off-by: NRongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the compiler warnings: "comparison is always
false due to limited range of data type" by using "0xff" instead
of "-1" for unsigned values.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change function rcu_dereference to rcu_dereference_bh to avoid warning

[ INFO: suspicious RCU usage. ]
-------------------------------
net/core/dev.c:2459 suspicious rcu_dereference_check() usage!

because we are locking with

rcu_read_lock_bh();

in function dev_queue_xmit(struct sk_buff *skb)
Signed-off-by: NIgor Maravic <igorm@etf.rs>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a custom flow dissector, use skb_flow_dissect() and
benefit from tunnelling support.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a custom flow dissector, use skb_flow_dissect() and
benefit from tunnelling support.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_sendmsg() uses select_size() helper to choose skb head size when a
new skb must be allocated.

If GSO is enabled for the socket, current strategy is to force all
payload data to be outside of headroom, in PAGE fragments.

This strategy is not welcome for small packets, wasting memory.

Experiments show that best results are obtained when using 2048 bytes
for skb head (This includes the skb overhead and various headers)

This patch provides better len/truesize ratios for packets sent to
loopback device, and reduce memory needs for in-flight loopback packets,
particularly on arches with big pages.

If a sender sends many 1-byte packets to an unresponsive application,
receiver rmem_alloc will grow faster and will stop queuing these packets
sooner, or will collapse its receive queue to free excess memory.

netperf -t TCP_RR results are improved by ~4 %, and many workloads are
improved as well (tbench, mysql...)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Le lundi 28 novembre 2011 à 19:06 -0500, David Miller a écrit :
> From: Dimitris Michailidis <dm@chelsio.com>
> Date: Mon, 28 Nov 2011 08:25:39 -0800
>
> >> +bool skb_flow_dissect(const struct sk_buff *skb, struct flow_keys
> >> *flow)
> >> +{
> >> +	int poff, nhoff = skb_network_offset(skb);
> >> +	u8 ip_proto;
> >> +	u16 proto = skb->protocol;
> >
> > __be16 instead of u16 for proto?
>
> I'll take care of this when I apply these patches.

( CC trimmed )

Thanks David !

Here is a small patch to use one 64bit load/store on x86_64 instead of
two 32bit load/stores.

[PATCH net-next] flow_dissector: use a 64bit load/store

gcc compiler is smart enough to use a single load/store if we
memcpy(dptr, sptr, 8) on x86_64, regardless of
CONFIG_CC_OPTIMIZE_FOR_SIZE

In IP header, daddr immediately follows saddr, this wont change in the
future. We only need to make sure our flow_keys (src,dst) fields wont
break the rule.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to sfc to use byte queue limits.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to bnx2x to use byte queue limits.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to tg3 to use byte queue limits.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to forcedeth to use byte queue limits.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to e1000e to use byte queue limits.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Networking stack support for byte queue limits, uses dynamic queue
limits library.  Byte queue limits are maintained per transmit queue,
and a dql structure has been added to netdev_queue structure for this
purpose.

Configuration of bql is in the tx-<n> sysfs directory for the queue
under the byte_queue_limits directory.  Configuration includes:
limit_min, bql minimum limit
limit_max, bql maximum limit
hold_time, bql slack hold time

Also under the directory are:
limit, current byte limit
inflight, current number of bytes on the queue
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the xps specific parts in netdev_queue_release into
its own function which netdev_queue_release can call.  This allows
netdev_queue_release to be more generic (for adding new attributes
to tx queues).
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add interfaces for drivers to call for recording number of packets and
bytes at send time and transmit completion.  Also, added a function to
"reset" a queue.  These will be used by Byte Queue Limits.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create separate queue state flags so that either the stack or drivers
can turn on XOFF.  Added a set of functions used in the stack to determine
if a queue is really stopped (either by stack or driver)
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implementation of dynamic queue limits (dql).  This is a libary which
allows a queue limit to be dynamically managed.  The goal of dql is
to set the queue limit, number of objects to the queue, to be minimized
without allowing the queue to be starved.

dql would be used with a queue which has these properties:

1) Objects are queued up to some limit which can be expressed as a
   count of objects.
2) Periodically a completion process executes which retires consumed
   objects.
3) Starvation occurs when limit has been reached, all queued data has
   actually been consumed but completion processing has not yet run,
   so queuing new data is blocked.
4) Minimizing the amount of queued data is desirable.

A canonical example of such a queue would be a NIC HW transmit queue.

The queue limit is dynamic, it will increase or decrease over time
depending on the workload.  The queue limit is recalculated each time
completion processing is done.  Increases occur when the queue is
starved and can exponentially increase over successive intervals.
Decreases occur when more data is being maintained in the queue than
needed to prevent starvation.  The number of extra objects, or "slack",
is measured over successive intervals, and to avoid hysteresis the
limit is only reduced by the miminum slack seen over a configurable
time period.

dql API provides routines to manage the queue:
- dql_init is called to intialize the dql structure
- dql_reset is called to reset dynamic values
- dql_queued called when objects are being enqueued
- dql_avail returns availability in the queue
- dql_completed is called when objects have be consumed in the queue

Configuration consists of:
- max_limit, maximum limit
- min_limit, minimum limit
- slack_hold_time, time to measure instances of slack before reducing
  queue limit
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the XGMAC 10Gb ethernet device in the Calxeda Highbank
SOC.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Round-up some wayward "N/A" fw_version dust bunnies as part of that
clean-up.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since 2005 (c1b4a7e6)
tcp_tso_should_defer has been using tcp_max_burst() as a target limit
for deciding how large to make outgoing TSO packets when not using
sysctl_tcp_tso_win_divisor. But since 2008
(dd9e0dda) tcp_max_burst() returns the
reordering degree. We should not have tcp_tso_should_defer attempt to
build larger segments just because there is more reordering. This
commit splits the notion of deferral size used in TSO from the notion
of burst size used in cwnd moderation, and returns the TSO deferral
limit to its original value.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use memcmp() instead of cast to u16 when checking the PAD field.
Signed-off-by: NPascal Hambourg <pascal@plouf.fr.eu.org>
Signed-off-by: Nchas williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Routed payload requires less headroom than bridged payload.
So do not reallocate headroom if not needed.
Also, add worst case AAL5 overhead to netdev->hard_header_len.
Signed-off-by: NPascal Hambourg <pascal@plouf.fr.eu.org>
Signed-off-by: Nchas williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can test/set multiple bits from sk_flags at once, to shorten a bit
socket setup/dismantle phase.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Igor Maravic reported an error caused by jump_label_dec() being called
from IRQ context :

 BUG: sleeping function called from invalid context at kernel/mutex.c:271
 in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper
 1 lock held by swapper/0:
  #0:  (&n->timer){+.-...}, at: [<ffffffff8107ce90>] call_timer_fn+0x0/0x340
 Pid: 0, comm: swapper Not tainted 3.2.0-rc2-net-next-mpls+ #1
Call Trace:
 <IRQ>  [<ffffffff8104f417>] __might_sleep+0x137/0x1f0
 [<ffffffff816b9a2f>] mutex_lock_nested+0x2f/0x370
 [<ffffffff810a89fd>] ? trace_hardirqs_off+0xd/0x10
 [<ffffffff8109a37f>] ? local_clock+0x6f/0x80
 [<ffffffff810a90a5>] ? lock_release_holdtime.part.22+0x15/0x1a0
 [<ffffffff81557929>] ? sock_def_write_space+0x59/0x160
 [<ffffffff815e936e>] ? arp_error_report+0x3e/0x90
 [<ffffffff810969cd>] atomic_dec_and_mutex_lock+0x5d/0x80
 [<ffffffff8112fc1d>] jump_label_dec+0x1d/0x50
 [<ffffffff81566525>] net_disable_timestamp+0x15/0x20
 [<ffffffff81557a75>] sock_disable_timestamp+0x45/0x50
 [<ffffffff81557b00>] __sk_free+0x80/0x200
 [<ffffffff815578d0>] ? sk_send_sigurg+0x70/0x70
 [<ffffffff815e936e>] ? arp_error_report+0x3e/0x90
 [<ffffffff81557cba>] sock_wfree+0x3a/0x70
 [<ffffffff8155c2b0>] skb_release_head_state+0x70/0x120
 [<ffffffff8155c0b6>] __kfree_skb+0x16/0x30
 [<ffffffff8155c119>] kfree_skb+0x49/0x170
 [<ffffffff815e936e>] arp_error_report+0x3e/0x90
 [<ffffffff81575bd9>] neigh_invalidate+0x89/0xc0
 [<ffffffff81578dbe>] neigh_timer_handler+0x9e/0x2a0
 [<ffffffff81578d20>] ? neigh_update+0x640/0x640
 [<ffffffff81073558>] __do_softirq+0xc8/0x3a0

Since jump_label_{inc|dec} must be called from process context only,
we must defer jump_label_dec() if net_disable_timestamp() is called
from interrupt context.
Reported-by: NIgor Maravic <igorm@etf.rs>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the drivers in drivers/net/ethernet/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the drivers in drivers/net/can/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Kurt Van Dijck <kurt.van.dijck@eia.be>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Linux coding style wants the return statement on its own line.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nr_route.ndigis is unsigned int so the nr_route.ndigis < 0 expression is
never true and can be dropped.  Doing the nr_ax25_dev_get call later
allows the nr_route.ndigis test to bail out without having to dev_put.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Thomas Osterried <thomas@osterried.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct nr_route_struct's mnemonic permits a string of up to 7 bytes to be
used.  If userland passes a not zero terminated string to the kernel adding
a node to the routing table might result in the kernel attempting to read
copy a too long string.

Mnemonic is part of the NET/ROM routing protocol; NET/ROM routing table
updates only broadcast 6 bytes.  The 7th byte in the mnemonic array exists
only as a \0 termination character for the kernel code's convenience.

Fixed by rejecting mnemonic strings that have no terminating \0 in the first
7 characters.  Do this test only NETROM_NODE to avoid breaking NETROM_NEIGH
where userland might passing an uninitialized mnemonic field.

Initial patch by Dan Carpenter <dan.carpenter@oracle.com>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Walter Harms <wharms@bfs.de>
Cc: Thomas Osterried <thomas@osterried.de>
Acked-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Very large, nonsenical arguments or use in very extreme conditions could
result in integer overflows.  Check ioctls arguments to avoid such
overflows and return -EINVAL for too large arguments.

To allow the use of AX.25 for even the most extreme setup (think packet
radio to the Phase 5E mars probe) we make no further attempt to clamp the
argument range.

Originally reported by Fan Long <longfancn@gmail.com> and a first patch
was sent by Xi Wang <xi.wang@gmail.com>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Xi Wang <xi.wang@gmail.com>
Cc: Joerg Reuter <jreuter@yaina.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Thomas Osterried <thomas@osterried.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>