The interface h->ae_algo->ops->put_vector is called in both
hns3_nic_dealloc_vector_data and hns3_nic_uninit_vector_data in
hns3_client_uninit, this will cause vector freed twice.
This patch remove the Redundant put_vector to make vector freed
only once.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print the ret value in error information can help find the reason.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extraction an interface for state init|uninit to make the code
easier to read.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

linux/slab.h is not used in hnae3.h, this patch removes it.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first bd of a packet is invalid and invalid ring head for tx
IRQ is not offen, they may occur when there is error,
Add unlikely for error check branch is better for performance.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW supports UDP, TCP and SCTP packets checksum for both ipv4 and
ipv6,  but do not support other type packets checksum for ipv4 or
ipv6.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the hdev->vector_status[vector_id] is already HCLGE_INVALID_VPORT,
should log the error and return.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interface init_client_instance and uninit_client_instance
do not register anything, only initialize the client instance.
This patch rename the related interface to make the function
name to indicate the purpose.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hclge_unmap_ring_frm_vector, there are 2 steps:
step 1: get vector index.
step 2 unbind ring with vector.

But it gets vector id again in step 2 interface. This patch
removes hclge_get_vector_index from hclge_bind_ring_with_vector,
and make the step the same with hns3 PF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flavio Leitner says:

====================
net: preserve sock reference when scrubbing the skb.

The sock reference is lost when scrubbing the packet and that breaks
TSQ (TCP Small Queues) and XPS (Transmit Packet Steering) causing
performance impacts of about 50% in a single TCP stream when crossing
network namespaces.

XPS breaks because the queue mapping stored in the socket is not
available, so another random queue might be selected when the stack
needs to transmit something like a TCP ACK, or TCP Retransmissions.
That causes packet re-ordering and/or performance issues.

TSQ breaks because it orphans the packet while it is still in the
host, so packets are queued contributing to the buffer bloat problem.

Preserving the sock reference fixes both issues. The socket is
orphaned anyways in the receiving path before any relevant action,
but the transmit side needs some extra checking included in the
first patch.

The first patch will update netfilter to check if the socket
netns is local before use it.

The second patch removes the skb_orphan() from the skb_scrub_packet()
and improve the documentation.

ChangeLog:
- split into two (Eric)
- addressed Paolo's offline feedback to swap the checks in xt_socket.c
  to preserve original behavior.
- improved ip-sysctl.txt (reported by Cong)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sock reference is lost when scrubbing the packet and that breaks
TSQ (TCP Small Queues) and XPS (Transmit Packet Steering) causing
performance impacts of about 50% in a single TCP stream when crossing
network namespaces.

XPS breaks because the queue mapping stored in the socket is not
available, so another random queue might be selected when the stack
needs to transmit something like a TCP ACK, or TCP Retransmissions.
That causes packet re-ordering and/or performance issues.

TSQ breaks because it orphans the packet while it is still in the
host, so packets are queued contributing to the buffer bloat problem.

Preserving the sock reference fixes both issues. The socket is
orphaned anyways in the receiving path before any relevant action
and on TX side the netfilter checks if the reference is local before
use it.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netfilter assumes that if the socket is present in the skb, then
it can be used because that reference is cleaned up while the skb
is crossing netns.

We want to change that to preserve the socket reference in a future
patch, so this is a preparation updating netfilter to check if the
socket netns matches before use it.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roman Mashak says:

====================
net sched actions: code style cleanup and fixes

The patchset fixes a few code stylistic issues and typos, as well as one
detected by sparse semantic checker tool.

No functional changes introduced.

Patch 1 & 2 fix coding style bits caught by the checkpatch.pl script
Patch 3 fixes an issue with a shadowed variable
Patch 4 adds sizeof() operator instead of magic number for buffer length
Patch 5 fixes typos in diagnostics messages
Patch 6 explicitly sets unsigned char for bitwise operation

v2:
   - submit for net-next
   - added Reviewed-by tags
   - use u8* instead of char* as per Davide Caratti suggestion
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since char can be unsigned or signed, and bitwise operators may have
implementation-dependent results when performed on signed operands,
declare 'u8 *' operand instead.
Suggested-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change "tc filter pedit .." to "tc actions pedit .." in error
messages to clearly refer to pedit action.
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace constant integer with sizeof() to clearly indicate
the destination buffer length in skb_header_pointer() calls.
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable _data in include/asm-generic/sections.h defines sections,
this causes sparse warning in pedit:

net/sched/act_pedit.c:293:35: warning: symbol '_data' shadows an earlier one
./include/asm-generic/sections.h:36:13: originally declared here

Therefore rename the variable.
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coding style issues in tc pedit headers detected by the
checkpatch script.
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coding style issues in tc pedit action detected by the
checkpatch script.
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend slotting with support for non-uniform distributions. This is
similar to netem's non-uniform distribution delay feature.

Commit f043efeae2f1 ("netem: support delivering packets in delayed
time slots") added the slotting feature to approximate the behaviors
of media with packet aggregation but only supported a uniform
distribution for delays between transmission attempts. Tests with TCP
BBR with emulated wifi links with non-uniform distributions produced
more useful results.

Syntax:
   slot dist DISTRIBUTION DELAY JITTER [packets MAX_PACKETS] \
      [bytes MAX_BYTES]

The syntax and use of the distribution table is the same as in the
non-uniform distribution delay feature. A file DISTRIBUTION must be
present in TC_LIB_DIR (e.g. /usr/lib/tc) containing numbers scaled by
NETEM_DIST_SCALE. A random value x is selected from the table and it
takes DELAY + ( x * JITTER ) as delay. Correlation between values is not
supported.

Examples:
  Normal distribution delay with mean = 800us and stdev = 100us.
  > tc qdisc add dev eth0 root netem slot dist normal 800us 100us

  Optionally set the max slot size in bytes and/or packets.
  > tc qdisc add dev eth0 root netem slot dist normal 800us 100us \
    bytes 64k packets 42
Signed-off-by: NYousuk Seung <ysseung@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have one extack message for parsing and validating.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.
Signed-off-by: NBrandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The xgmiitorgmii is using the mii_bus of the device it's attached to,
instead of the bus it was given during probe.
Signed-off-by: NBrandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().

Fixes this Oops:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>]    lr : [<c0529548>]    psr: 20000013
sp : ce4cbb54  ip : 00000000  fp : ce4cbb8c
r10: 00000000  r9 : 00000000  r8 : c0c49178
r7 : 00000000  r6 : cdc14718  r5 : ce762800  r4 : cdc14710
r3 : 00000000  r2 : 00000054  r1 : 00000000  r0 : cdc14718
Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 18c5387d  Table: 0000404a  DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: NBrandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
Updates for ipsec selftests

Fix up the existing ipsec selftest and add tests for
the ipsec offload driver API.

v2: addressed formatting nits in netdevsim from Jakub Kicinski
v3: a couple more nits from Jakub
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using the netdevsim as a device for testing, try out the XFRM commands
for setting up IPsec hardware offloads.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the IPsec/XFRM offload API for testing.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We really shouldn't mess with local system settings, so let's
use the already created dummy device instead for ipsec testing.
Oh, and let's put the temp file into a proper directory.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following the custom from the other functions, clear the global
ret code before starting the test so as to not have previously
failed tests cause us to thing this test has failed.
Reported-by: NAnders Roxell <anders.roxell@linaro.org>
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'sockaddr_len' is checked against various values when entering
pppol2tp_connect(), to verify its validity. It is used again later, to
find out which sockaddr structure was passed from user space. This
patch combines these two operations into one new function in order to
simplify pppol2tp_connect().

A new structure, l2tp_connect_info, is used to pass sockaddr data back
to pppol2tp_connect(), to avoid passing too many parameters to
l2tp_sockaddr_get_info(). Also, the first parameter is void* in order
to avoid casting between all sockaddr_* structures manually.
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The *enum* {A|M}PR_BIT were declared in the commit 86a74ff2 ("net:
sh_eth: add support for  Renesas SuperH Ethernet") adding SH771x support,
however the SH771x manual  doesn't have the APR/MPR registers described
and the code writing to them for SH7710 was later removed by the commit
380af9e3 ("net: sh_eth: CPU dependency code collect to "struct
sh_eth_cpu_data""). All the newer SoC manuals have these registers
documented as having a 16-bit TIME parameter of the PAUSE frame, not
1-bit -- update the *enum* accordingly, fixing up the APR/MPR writes...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added an extreme-case test for all 7 csum action headers.
Signed-off-by: NKeara Leibovitz <kleib@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexandre Belloni says:

====================
net: mscc: ocelot: add more features

This series adds link aggregation and VLAN filtering hardware offload
support to the ocelot driver.

PTP support will be sent later.

changes in v2:
 - rebased on v4.18-rc1
 - check for aggregation type and only offload it when type is hash (balance-xor
   or 802.3ad)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add hardware VLAN filtering offloading on ocelot.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add link aggregation hardware offload support for Ocelot.

ocelot_get_link_ksettings() is not great but it does work until the driver
is reworked to switch to phylink.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add flag tc_flower_initialized to indicate the
completion if tc flower initialization.
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In systems where neigh gc thresh holds are set to high values,
admin deleted neigh entries (eg ip neigh flush or ip neigh del) can
linger around in NUD_FAILED state for a long time until periodic gc kicks
in. This patch forces neigh_invalidate when NUD_FAILED neigh_update is
from an admin.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Petr Machata says:

====================
Multipath tests for tunnel devices

This patchset adds a test for ECMP and weighted ECMP between two GRE
tunnels.

In patches #1 and #2, the function multipath_eval() is first moved from
router_multipath.sh to lib.sh for ease of reuse, and then fixed up.

In patch #3, the function tc_rule_stats_get() is parameterized to be
useful for egress rules as well.

In patch #4, a new function __simple_if_init() is extracted from
simple_if_init(). This covers the logic that needs to be done for the
usual interface: VRF migration, upping and installation of IP addresses.

Patch #5 then adds the test itself.

Additionally in patch #6, a requirement to add diagrams to selftests is
documented.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>