The QPTS register allows changing the priority trust state between pcp and
dscp. Add support to get/set trust state from device. When the port is
in pcp/dscp trust state, packet is routed by hardware to matching priority
based on its pcp/dscp value respectively.

The QPDPM register allow channing the dscp to priority mapping. Add support
to get/set dscp to priority mapping from device.
Note that to change a dscp mapping, the "e" bit of this dscp structure
must be set in the QPDPM firmware command.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add MLX5_SET16 and MLX5_GET16 for 16bit structure field in firmware
command.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The QCAM register provides capability bit for all the QoS registers
using ACCESS_REG command.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

One page may store a set of entries of the sis->swap_map
(swap_info_struct->swap_map) in multiple swap clusters.

If some of the entries has sis->swap_map[offset] > SWAP_MAP_MAX,
multiple pages will be used to store the set of entries of the
sis->swap_map.  And the pages are linked with page->lru.  This is called
swap count continuation.  To access the pages which store the set of
entries of the sis->swap_map simultaneously, previously, sis->lock is
used.  But to improve the scalability of __swap_duplicate(), swap
cluster lock may be used in swap_count_continued() now.  This may race
with add_swap_count_continuation() which operates on a nearby swap
cluster, in which the sis->swap_map entries are stored in the same page.

The race can cause wrong swap count in practice, thus cause unfreeable
swap entries or software lockup, etc.

To fix the race, a new spin lock called cont_lock is added to struct
swap_info_struct to protect the swap count continuation page list.  This
is a lock at the swap device level, so the scalability isn't very well.
But it is still much better than the original sis->lock, because it is
only acquired/released when swap count continuation is used.  Which is
considered rare in practice.  If it turns out that the scalability
becomes an issue for some workloads, we can split the lock into some
more fine grained locks.

Link: http://lkml.kernel.org/r/20171017081320.28133-1-ying.huang@intel.com
Fixes: 235b6217 ("mm/swap: add cluster lock")
Signed-off-by: N"Huang, Ying" <ying.huang@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>	[4.11+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In sch_handle_egress and sch_handle_ingress tp->q is used only in order
to update stats. So stats and filter list are the only things that are
needed in clsact qdisc fastpath processing. Introduce new mini_Qdisc
struct to hold those items. Also, introduce a helper to swap the
mini_Qdisc structures in case filter list head changes.

This removes need for tp->q usage without added overhead.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The lan9303 driver defines eth_stp_addr as a synonym to
eth_reserved_addr_base to get the STP ethernet address 01:80:c2:00:00:00.

eth_reserved_addr_base is also used to define the start of Bridge Reserved
ethernet address range, which happen to be the STP address.

br_dev_setup refer to eth_reserved_addr_base as a definition of STP
address.

Clean up by:
 - Move the eth_stp_addr definition to linux/etherdevice.h
 - Use eth_stp_addr instead of eth_reserved_addr_base in br_dev_setup.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.

This causes it to always return 0 with little-endian
architectures.

Fix it by using of_property_read_u32() OF API.
Signed-off-by: NBhadram Varka <vbhadram@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Touching linux/bpf.h makes us rebuild a surprisingly large
portion of the kernel.  Remove the unnecessary dependency
from security.h, it only needs forward declarations.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.

Add an ALR entry with STP state override to fix that.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the verifier got progressively smarter over time and size of its internal
state grew as well. Time to reduce the memory consumption.

Before:
sizeof(struct bpf_verifier_state) = 6520
After:
sizeof(struct bpf_verifier_state) = 896

It's done by observing that majority of BPF programs use little to
no stack whereas verifier kept all of 512 stack slots ready always.
Instead dynamically reallocate struct verifier state when stack
access is detected.
Runtime difference before vs after is within a noise.
The number of processed instructions stays the same.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 0cc2b4e5 (PM / QoS: Fix device resume latency PM
QoS) as it introduced regressions on multiple systems and the fix-up
in commit 2a9a86d5 (PM / QoS: Fix default runtime_pm device resume
latency) does not address all of them.

The original problem that commit 0cc2b4e5 was attempting to fix
will be addressed later.

Fixes: 0cc2b4e5 (PM / QoS: Fix device resume latency PM QoS)
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This reverts commit 2a9a86d5 (PM / QoS: Fix default runtime_pm
device resume latency) as the commit it depends on is going to be
reverted.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The recent change to the PM QoS framework to introduce a proper
no constraint value overlooked to handle the devices which don't
implement PM QoS OPS.  Runtime PM is one of the more severely
impacted subsystems, failing every attempt to runtime suspend
a device.  This leads into some nasty second level issues like
probe failures and increased power consumption among other
things.

Fix this by adding a proper return value for devices that don't
implement PM QoS.

Fixes: 0cc2b4e5 (PM / QoS: Fix device resume latency PM QoS)
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.

Note after this patch, there still one warning left in
sctp_outq_flush():
  sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)

Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These warnings were found by running 'make C=2 M=net/sctp/'.

They are introduced by not aware of Endian when coding stream
reconf patches.

Since commit c0d8bab6 ("sctp: add get and set sockopt for
reconf_enable") enabled stream reconf feature for users, the
Fixes tag below would use it.

Fixes: c0d8bab6 ("sctp: add get and set sockopt for reconf_enable")
Reported-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 9a393b5d ("tap: tap as an independent module") created a
separate tap module that implements tap functionality and exports
interfaces that will be used by macvtap and ipvtap modules to create
create respective tap devices.

However, that patch introduced a regression wherein the modules macvtap
and ipvtap can be removed (through modprobe -r) while there are
applications using the respective /dev/tapX devices. These applications
cause kernel to hold reference to /dev/tapX through 'struct cdev
macvtap_cdev' and 'struct cdev ipvtap_dev' defined in macvtap and ipvtap
modules respectively. So,  when the application is later closed the
kernel panics because we are referencing KVA that is present in the
unloaded modules.

----------8<------- Example ----------8<----------
$ sudo ip li add name mv0 link enp7s0 type macvtap
$ sudo ip li show mv0 |grep mv0| awk -e '{print $1 $2}'
  14:mv0@enp7s0:
$ cat /dev/tap14 &
$ lsmod |egrep -i 'tap|vlan'
macvtap                16384  0
macvlan                24576  1 macvtap
tap                    24576  3 macvtap
$ sudo modprobe -r macvtap
$ fg
cat /dev/tap14
^C

<...system panics...>
BUG: unable to handle kernel paging request at ffffffffa038c500
IP: cdev_put+0xf/0x30
----------8<-----------------8<----------

The fix is to set cdev.owner to the module that creates the tap device
(either macvtap or ipvtap). With this set, the operations (in
fs/char_dev.c) on char device holds and releases the module through
cdev_get() and cdev_put() and will not allow the module to unload
prematurely.

Fixes: 9a393b5d (tap: tap as an independent module)
Signed-off-by: NGirish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for offloading the CBS algorithm to the controller,
if supported. Drivers wanting to support CBS offload must implement
the .ndo_setup_tc callback and handle the TC_SETUP_CBS (introduced
here) type.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NHenrik Austad <henrik@austad.us>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The next patch require net/dsa/tag_lan9303.c to access struct lan9303.
Therefore move struct lan9303 definitions from drivers/net/dsa/lan9303.h
to new file include/linux/dsa/lan9303.h.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit afdb09c7 ("security: bpf: Add LSM hooks for bpf object related
syscall") included linux/bpf.h in linux/security.h. As a result, bpf
programs including bpf_helpers.h and some other header that ends up
pulling in also security.h, such as several examples under samples/bpf,
fail to compile because bpf_tail_call and bpf_get_stackid are now
"redefined as different kind of symbol".

>From bpf.h:

u64 bpf_tail_call(u64 ctx, u64 r2, u64 index, u64 r4, u64 r5);
u64 bpf_get_stackid(u64 r1, u64 r2, u64 r3, u64 r4, u64 r5);

Whereas in bpf_helpers.h they are:

static void (*bpf_tail_call)(void *ctx, void *map, int index);
static int (*bpf_get_stackid)(void *ctx, void *map, int flags);

Fix this by removing the unused declaration of bpf_tail_call and moving
the declaration of bpf_get_stackid in bpf_trace.c, which is the only
place where it's needed.
Signed-off-by: NGianluca Borello <g.borello@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Allen Pais <allen.lkml@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SMC protocol [1] relies on the use of a new TCP experimental
option [2, 3]. With this option, SMC capabilities are exchanged
between peers during the TCP three way handshake. This patch adds
support for this experimental option to TCP.

References:
[1] SMC-R Informational RFC: http://www.rfc-editor.org/info/rfc7609
[2] Shared Use of TCP Experimental Options RFC 6994:
    https://tools.ietf.org/rfc/rfc6994.txt
[3] IANA ExID SMCR:
http://www.iana.org/assignments/tcp-parameters/tcp-parameters.xhtml#tcp-exidsSigned-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, tc with ets type and zero bandwidth is not accepted
by driver. This behavior does not follow the IEEE802.1qaz spec.

If there are tcs with ets type and zero bandwidth, these tcs are
assigned to the lowest priority tc_group #0. We equally distribute
100% bw of the tc_group #0 to these zero bandwidth ets tcs.
Also, the non zero bandwidth ets tcs are assigned to tc_group #1.

If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs
are assigned to tc_group #0.

Fixes: cdcf1121 ("net/mlx5e: Validate BW weight values of ETS")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

commit 635b8c8e ("tap: Renaming tap related APIs, data structures,
macros") captured all the tap related fields into a new struct tap_dev.
However, it failed to remove those fields from struct macvlan_dev.
Those fields are currently unused and must be removed. While there
I moved the comment for MAX_TAP_QUEUES to the right place.

Fixes: 635b8c8e (tap: Renaming tap related APIs, data structures, macros)
Signed-off-by: NGirish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables multiple bpf attachments for a
kprobe/uprobe/tracepoint single trace event.
Each trace_event keeps a list of attached perf events.
When an event happens, all attached bpf programs will
be executed based on the order of attachment.

A global bpf_event_mutex lock is introduced to protect
prog_array attaching and detaching. An alternative will
be introduce a mutex lock in every trace_event_call
structure, but it takes a lot of extra memory.
So a global bpf_event_mutex lock is a good compromise.

The bpf prog detachment involves allocation of memory.
If the allocation fails, a dummy do-nothing program
will replace to-be-detached program in-place.
Signed-off-by: NYonghong Song <yhs@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.

First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value.  However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.

Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.

To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.

Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.

Fixes: 85dc0b8a (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323Reported-by: NReinette Chatre <reinette.chatre@intel.com>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NAlex Shi <alex.shi@linaro.org>
Cc: All applicable <stable@vger.kernel.org>

We already allow to enable TFO without a cookie by using the
fastopen-sysctl and setting it to TFO_SERVER_COOKIE_NOT_REQD (or
TFO_CLIENT_NO_COOKIE).
This is safe to do in certain environments where we know that there
isn't a malicous host (aka., data-centers) or when the
application-protocol already provides an authentication mechanism in the
first flight of data.

A server however might be providing multiple services or talking to both
sides (public Internet and data-center). So, this server would want to
enable cookie-less TFO for certain services and/or for connections that
go to the data-center.

This patch exposes a socket-option and a per-route attribute to enable such
fine-grained configurations.
Signed-off-by: NChristoph Paasch <cpaasch@apple.com>
Reviewed-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently welcome using swait over wait whenever possible because
it is a slimmer data structure. However, Linus has made it very clear
that he does not want this used, unless under very specific RT scenarios
(such as current users).

Update the comments before kernel hipsters start thinking swait is the
cool thing to do.
Signed-off-by: NDavidlohr Bueso <dbueso@suse.de>
Acked-by: NLuis R. Rodriguez <mcgrof@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: wagi@monom.org
Link: http://lkml.kernel.org/r/20171020171346.24445-1-dave@stgolabs.netSigned-off-by: NIngo Molnar <mingo@kernel.org>

atomic_t variables are currently used to implement reference
counters with the following properties:
 - counter is initialized to 1 using atomic_set()
 - a resource is freed upon counter reaching zero
 - once counter reaches zero, its further
   increments aren't allowed
 - counter schema uses basic atomic operations
   (set, inc, inc_not_zero, dec_and_test, etc.)

Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.

The variable cn_callback_entry.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NDavid Windsor <dwindsor@gmail.com>
Reviewed-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

atomic_t variables are currently used to implement reference
counters with the following properties:
 - counter is initialized to 1 using atomic_set()
 - a resource is freed upon counter reaching zero
 - once counter reaches zero, its further
   increments aren't allowed
 - counter schema uses basic atomic operations
   (set, inc, inc_not_zero, dec_and_test, etc.)

Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.

The variable mlx5_cq.refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NDavid Windsor <dwindsor@gmail.com>
Reviewed-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

atomic_t variables are currently used to implement reference
counters with the following properties:
 - counter is initialized to 1 using atomic_set()
 - a resource is freed upon counter reaching zero
 - once counter reaches zero, its further
   increments aren't allowed
 - counter schema uses basic atomic operations
   (set, inc, inc_not_zero, dec_and_test, etc.)

Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.

The variable mlx4_srq.refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NDavid Windsor <dwindsor@gmail.com>
Reviewed-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

atomic_t variables are currently used to implement reference
counters with the following properties:
 - counter is initialized to 1 using atomic_set()
 - a resource is freed upon counter reaching zero
 - once counter reaches zero, its further
   increments aren't allowed
 - counter schema uses basic atomic operations
   (set, inc, inc_not_zero, dec_and_test, etc.)

Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.

The variable mlx4_qp.refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NDavid Windsor <dwindsor@gmail.com>
Reviewed-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

atomic_t variables are currently used to implement reference
counters with the following properties:
 - counter is initialized to 1 using atomic_set()
 - a resource is freed upon counter reaching zero
 - once counter reaches zero, its further
   increments aren't allowed
 - counter schema uses basic atomic operations
   (set, inc, inc_not_zero, dec_and_test, etc.)

Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.

The variable mlx4_cq.refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NDavid Windsor <dwindsor@gmail.com>
Reviewed-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce new type of ndo_setup_tc message to propage binding/unbinding
of a block to driver. Call this ndo whenever qdisc gets/puts a block.
Alongside with this, there's need to propagate binder type from qdisc
code down to the notifier. So introduce extended variants of
block_get/put in order to pass this info.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a bpf object related check when sending and receiving files
through unix domain socket as well as binder. It checks if the receiving
process have privilege to read/write the bpf map or use the bpf program.
This check is necessary because the bpf maps and programs are using a
anonymous inode as their shared inode so the normal way of checking the
files and sockets when passing between processes cannot work properly on
eBPF object. This check only works when the BPF_SYSCALL is configured.
Signed-off-by: NChenbo Feng <fengc@google.com>
Acked-by: NStephen Smalley <sds@tycho.nsa.gov>
Reviewed-by: NJames Morris <james.l.morris@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce several LSM hooks for the syscalls that will allow the
userspace to access to eBPF object such as eBPF programs and eBPF maps.
The security check is aimed to enforce a per object security protection
for eBPF object so only processes with the right priviliges can
read/write to a specific map or use a specific eBPF program. Besides
that, a general security hook is added before the multiplexer of bpf
syscall to check the cmd and the attribute used for the command. The
actual security module can decide which command need to be checked and
how the cmd should be checked.
Signed-off-by: NChenbo Feng <fengc@google.com>
Acked-by: NJames Morris <james.l.morris@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce the map read/write flags to the eBPF syscalls that returns the
map fd. The flags is used to set up the file mode when construct a new
file descriptor for bpf maps. To not break the backward capability, the
f_flags is set to O_RDWR if the flag passed by syscall is 0. Otherwise
it should be O_RDONLY or O_WRONLY. When the userspace want to modify or
read the map content, it will check the file mode to see if it is
allowed to make the change.
Signed-off-by: NChenbo Feng <fengc@google.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add extack to in_validator_info and in6_validator_info. Update the one
user of each, ipvlan, to return an error message for failures.

Only manual configuration of an address is plumbed in the IPv6 code path.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.

This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because many of RCU's files have not been included into docbook, a
number of errors have accumulated.  This commit fixes them.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>