Re-checking the faulty flag here brings no value.
The comment about "risk" refers to the risk that the device could
be in the process of being removed by ->hot_remove_disk().
However providing that the ->nr_pending count is incremented inside
an rcu_read_locked() region, there is no risk of that happening.

This is because the rdev pointer (in the personalities array) is set
to NULL before synchronize_rcu(), and ->nr_pending is tested
afterwards.  If the rcu_read_locked region happens before the
synchronize_rcu(), the test will see that nr_pending has been incremented.
If it happens afterwards, the rdev pointer will be NULL so there is nothing
to increment.
Signed-off-by: NNeilBrown <neilb@suse.com>
Signed-off-by: NShaohua Li <shli@fb.com>

A performance drop of mkfs has been observed on RAID10 during resync
since commit 09314799 ("md: remove 'go_faster' option from
->sync_request()"). Resync sends so many IOs it slows down non-resync
IOs significantly (few times). Add a short delay to a resync. The
previous long sleep (1s) has proven unnecessary, even very short delay
brings performance right.

The change also applied to raid1. The problem has not been observed on
raid1, however it shares barriers code with raid10 so it might be an
issue for some setup too.
Suggested-by: NNeilBrown <neilb@suse.com>
Link: http://lkml.kernel.org/r/20160609134555.GA9104@proton.igk.intel.comSigned-off-by: NTomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: NShaohua Li <shli@fb.com>

Some code waits for a metadata update by:

1. flagging that it is needed (MD_CHANGE_DEVS or MD_CHANGE_CLEAN)
2. setting MD_CHANGE_PENDING and waking the management thread
3. waiting for MD_CHANGE_PENDING to be cleared

If the first two are done without locking, the code in md_update_sb()
which checks if it needs to repeat might test if an update is needed
before step 1, then clear MD_CHANGE_PENDING after step 2, resulting
in the wait returning early.

So make sure all places that set MD_CHANGE_PENDING are atomicial, and
bit_clear_unless (suggested by Neil) is introduced for the purpose.

Cc: Martin Kepplinger <martink@posteo.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: <linux-kernel@vger.kernel.org>
Reviewed-by: NNeilBrown <neilb@suse.com>
Signed-off-by: NGuoqing Jiang <gqjiang@suse.com>
Signed-off-by: NShaohua Li <shli@fb.com>

If first_bad == this_sector when we get the WriteMostly disk
in read_balance(), valid disk will be returned with zero
max_sectors. It'll lead to a dead loop in make_request(), and
OOM will happen because of endless allocation of struct bio.

Since we can't get data from this disk in this case, so
continue for another disk.
Signed-off-by: NWei Fang <fangwei1@huawei.com>
Signed-off-by: NShaohua Li <shli@fb.com>

If raid1d is handling a mix of read and write errors, handle_read_error's
call to freeze_array can get stuck.

This can happen because, though the bio_end_io_list is initially drained,
writes can be added to it via handle_write_finished as the retry_list
is processed. These writes contribute to nr_pending but are not included
in nr_queued.

If a later entry on the retry_list triggers a call to handle_read_error,
freeze array hangs waiting for nr_pending == nr_queued+extra. The writes
on the bio_end_io_list aren't included in nr_queued so the condition will
never be satisfied.

To prevent the hang, include bio_end_io_list writes in nr_queued.

There's probably a better way to handle decrementing nr_queued, but this
seemed like the safest way to avoid breaking surrounding code.

I'm happy to supply the script I used to repro this hang.

Fixes: 55ce74d4(md/raid1: ensure device failure recorded before write request returns.)
Cc: stable@vger.kernel.org (v4.3+)
Signed-off-by: NNate Dailey <nate.dailey@stratus.com>
Signed-off-by: NShaohua Li <shli@fb.com>

Since bitmap_start_sync will not return until
sync_blocks is not less than PAGE_SIZE>>9, so
the BUG_ON is not needed anymore.
Signed-off-by: NGuoqing Jiang <gqjiang@suse.com>
Signed-off-by: NShaohua Li <shli@fb.com>

These short function names are hard to search. Rename them to make vim happy.
Signed-off-by: NShaohua Li <shli@fb.com>

It is not safe for an integrity profile to be changed while i/o is
in-flight in the queue.  Prevent adding new disks or otherwise online
spares to an array if the device has an incompatible integrity profile.

The original change to the blk_integrity_unregister implementation in
md, commmit c7bfced9 "md: suspend i/o during runtime
blk_integrity_unregister" introduced an immediate hang regression.

This policy of disallowing changes the integrity profile once one has
been established is shared with DM.

Here is an abbreviated log from a test run that:
1/ Creates a degraded raid1 with an integrity-enabled device (pmem0s) [   59.076127]
2/ Tries to add an integrity-disabled device (pmem1m) [   90.489209]
3/ Retries with an integrity-enabled device (pmem1s) [  205.671277]

[   59.076127] md/raid1:md0: active with 1 out of 2 mirrors
[   59.078302] md: data integrity enabled on md0
[..]
[   90.489209] md0: incompatible integrity profile for pmem1m
[..]
[  205.671277] md: super_written gets error=-5
[  205.677386] md/raid1:md0: Disk failure on pmem1m, disabling device.
[  205.677386] md/raid1:md0: Operation continuing on 1 devices.
[  205.683037] RAID1 conf printout:
[  205.684699]  --- wd:1 rd:2
[  205.685972]  disk 0, wo:0, o:1, dev:pmem0s
[  205.687562]  disk 1, wo:1, o:1, dev:pmem1s
[  205.691717] md: recovery of RAID array md0

Fixes: c7bfced9 ("md: suspend i/o during runtime blk_integrity_unregister")
Cc: <stable@vger.kernel.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Reported-by: NNeilBrown <neilb@suse.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

To incorporate --grow feature executed on one node, other nodes need to
acknowledge the change in number of disks. Call update_raid_disks()
to update internal data structures.

This leads to call check_reshape() -> md_allow_write() -> md_update_sb(),
this results in a deadlock. This is done so it can safely allocate memory
(which might trigger writeback which might write to raid1). This is
not required for md with a bitmap.

In the clustered case, we don't perform md_update_sb() in md_allow_write(),
but in do_md_run(). Also we disable safemode for clustered mode.

mddev->recovery_cp need not be set in check_sb_changes() because this
is required only when a node reads another node's bitmap. mddev->recovery_cp
(which is read from sb->resync_offset), is set only if mddev is in_sync.
Since we disabled safemode, in_sync is set to zero.
In a clustered environment, the MD may not be in sync because another
node could be writing to it. So make sure that in_sync is not set in
case of clustered node in __md_stop_writes().
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

When a write fails and a bad-block-list is present, we can
update the bad-block-list instead of writing the data.  If
this succeeds then it is OK clear the relevant bitmap-bit as
no further 'sync' of the block is needed.

However if writing the bad-block-list fails then we need to
treat the write as failed and particularly must not clear
the bitmap bit.  Otherwise the device can be re-added (after
any hardware connection issues are resolved) and because the
relevant bit in the bitmap is clear, that block will not be
resynced.  This leads to data corruption.

We already delay the final bio_endio() on the write until
the bad-block-list is written so that when the write
returns: either that data is safe, the bad-block record is
safe, or the fact that the device is faulty is safe.
However we *don't* delay the clearing of the bitmap, so the
bitmap bit can be recorded as cleared before we know if the
bad-block-list was written safely.

So: delay that until the write really is safe.
i.e. move the call to close_write() until just before
calling bio_endio(), and recheck the 'is array degraded'
status before making that call.

This bug goes back to v3.1 when bad-block-lists were
introduced, though it only affects arrays created with
mdadm-3.3 or later as only those have bad-block lists.

Backports will require at least
Commit: 55ce74d4 ("md/raid1: ensure device failure recorded before write request returns.")
as well.  I'll send that to 'stable' separately.

Note that of the two tests of R1BIO_WriteError that this
patch adds, the first is certain to fail and the second is
certain to succeed.  However doing it this way makes the
patch more obviously correct.  I will tidy the code up in a
future merge window.
Reported-and-tested-by: NNate Dailey <nate.dailey@stratus.com>
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Fixes: cd5ff9a1 ("md/raid1:  Handle write errors by updating badblock log.")
Signed-off-by: NNeilBrown <neilb@suse.com>

Synchronize pending i/o against a change in the integrity profile to
avoid the possibility of spurious integrity errors.  Given linear_add()
is suspending the mddev before manipulating the mddev, do the same for
the other personalities.
Acked-by: NNeilBrown <neilb@suse.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

This was introduced with 9e882242
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.

Fixes: 9e882242 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: NBill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

Resync or recovery must be performed by only one node at a time.
A DLM lock resource, resync_lockres provides the mutual exclusion
so that only one node performs the recovery/resync at a time.

If a node is unable to get the resync_lockres, because recovery is
being performed by another node, it set MD_RECOVER_NEEDED so as
to schedule recovery in the future.

Remove the debug message in resync_info_update()
used during development.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>

md_reload_sb is too simplistic and it explicitly needs to determine
the changes made by the writing node. However, there are multiple areas
where a simple reload could fail.

Instead, read the superblock of one of the "good" rdevs and update
the necessary information:

- read the superblock into a newly allocated page, by temporarily
  swapping out rdev->sb_page and calling ->load_super.
- if that fails return
- if it succeeds, call check_sb_changes
  1. iterates over list of active devices and checks the matching
   dev_roles[] value.
   	If that is 'faulty', the device must be  marked as faulty
	 - call md_error to mark the device as faulty. Make sure
	   not to set CHANGE_DEVS and wakeup mddev->thread or else
	   it would initiate a resync process, which is the responsibility
	   of the "primary" node.
	 - clear the Blocked bit
	 - Call remove_and_add_spares() to hot remove the device.
	If the device is 'spare':
	 - call remove_and_add_spares() to get the number of spares
	   added in this operation.
	 - Reduce mddev->degraded to mark the array as not degraded.
  2. reset recovery_cp
- read the rest of the rdevs to update recovery_offset. If recovery_offset
  is equal to MaxSector, call spare_active() to set it In_sync

This required that recovery_offset be initialized to MaxSector, as
opposed to zero so as to communicate the end of sync for a rdev.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>

Suspending the entire device for resync could take too long. Resync
in small chunks.

cluster's resync window (32M) is maintained in r1conf as
cluster_sync_low and cluster_sync_high and processed in
raid1's sync_request(). If the current resync is outside the cluster
resync window:

1. Set the cluster_sync_low to curr_resync_completed.
2. Check if the sync will fit in the new window, if not issue a
   wait_barrier() and set cluster_sync_low to sector_nr.
3. Set cluster_sync_high to cluster_sync_low + resync_window.
4. Send a message to all nodes so they may add it in their suspension
   list.

bitmap_cond_end_sync is modified to allow to force a sync inorder
to get the curr_resync_completed uptodate with the sector passed.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

The commit 55ce74d4 (md/raid1: ensure
device failure recorded before write request returns) is causing crash in
the LVM2 testsuite test shell/lvchange-raid.sh. For me the crash is 100%
reproducible.

The reason for the crash is that the newly added code in raid1d moves the
list from conf->bio_end_io_list to tmp, then tests if tmp is non-empty and
then incorrectly pops the bio from conf->bio_end_io_list (which is empty
because the list was alrady moved).

Raid-10 has a similar bug.

Kernel Fault: Code=15 regs=000000006ccb8640 (Addr=0000000100000000)
CPU: 3 PID: 1930 Comm: mdX_raid1 Not tainted 4.2.0-rc5-bisect+ #35
task: 000000006cc1f258 ti: 000000006ccb8000 task.ti: 000000006ccb8000

     YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111111000001111 Not tainted
r00-03  000000ff0804fe0f 000000001059d000 000000001059f818 000000007f16be38
r04-07  000000001059d000 000000007f16be08 0000000000200200 0000000000000001
r08-11  000000006ccb8260 000000007b7934d0 0000000000000001 0000000000000000
r12-15  000000004056f320 0000000000000000 0000000000013dd0 0000000000000000
r16-19  00000000f0d00ae0 0000000000000000 0000000000000000 0000000000000001
r20-23  000000000800000f 0000000042200390 0000000000000000 0000000000000000
r24-27  0000000000000001 000000000800000f 000000007f16be08 000000001059d000
r28-31  0000000100000000 000000006ccb8560 000000006ccb8640 0000000000000000
sr00-03  0000000000249800 0000000000000000 0000000000000000 0000000000249800
sr04-07  0000000000000000 0000000000000000 0000000000000000 0000000000000000

IASQ: 0000000000000000 0000000000000000 IAOQ: 000000001059f61c 000000001059f620
 IIR: 0f8010c6    ISR: 0000000000000000  IOR: 0000000100000000
 CPU:        3   CR30: 000000006ccb8000 CR31: 0000000000000000
 ORIG_R28: 000000001059d000
 IAOQ[0]: call_bio_endio+0x34/0x1a8 [raid1]
 IAOQ[1]: call_bio_endio+0x38/0x1a8 [raid1]
 RP(r2): raid_end_bio_io+0x88/0x168 [raid1]
Backtrace:
 [<000000001059f818>] raid_end_bio_io+0x88/0x168 [raid1]
 [<00000000105a4f64>] raid1d+0x144/0x1640 [raid1]
 [<000000004017fd5c>] kthread+0x144/0x160
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Fixes: 55ce74d4 ("md/raid1: ensure device failure recorded before write request returns.")
Fixes: 95af587e ("md/raid10: ensure device failure recorded before write request returns.")
Signed-off-by: NNeilBrown <neilb@suse.com>

close_sync() needs to set conf->next_resync to a large, but safe value
below MaxSector and use it to determine whether or not to set
start_next_window in wait_barrier()

Solution suggested by Neil Brown.
Reported-by: NNate Dailey <nate.dailey@stratus.com>
Tested-by: NXiao Ni <xni@redhat.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

Remove unneeded NULL test.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@ expression x; @@
-if (x != NULL)
  \(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NNeilBrown <neilb@suse.com>

When a write to one of the legs of a RAID1 fails, the failure is
recorded in the metadata of the other leg(s) so that after a restart
the data on the failed drive wont be trusted even if that drive seems
to be working again  (maybe a cable was unplugged).

Similarly when we record a bad-block in response to a write failure,
we must not let the write complete until the bad-block update is safe.

Currently there is no interlock between the write request completing
and the metadata update.  So it is possible that the write will
complete, the app will confirm success in some way, and then the
machine will crash before the metadata update completes.

This is an extremely small hole for a racy to fit in, but it is
theoretically possible and so should be closed.

So:
 - set MD_CHANGE_PENDING when requesting a metadata update for a
   failed device, so we can know with certainty when it completes
 - queue requests that experienced an error on a new queue which
   is only processed after the metadata update completes
 - call raid_end_bio_io() on bios in that queue when the time comes.
Signed-off-by: NNeilBrown <neilb@suse.com>

When checking sync_action in a script, we want to be sure it is
as accurate as possible.
As resync/reshape etc doesn't always start immediately (a separate
thread is scheduled to do it), it is best if 'action_show'
checks if MD_RECOVER_NEEDED is set (which it does) and in that
case reports what is likely to start soon (which it only sometimes
does).

So:
 - report 'reshape' if reshape_position suggests one might start.
 - set MD_RECOVERY_RECOVER in raid1_reshape(), because that is very
   likely to happen next.
Signed-off-by: NNeilBrown <neilb@suse.com>

As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.

Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NKent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
 dm-era-target, and resolve merge conflicts]
Signed-off-by: NDongsu Park <dpark@posteo.net>
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

raid1_end_read_request() assumes that the In_sync bits are consistent
with the ->degaded count.
raid1_spare_active updates the In_sync bit before the ->degraded count
and so exposes an inconsistency, as does error()
So extend the spinlock in raid1_spare_active() and error() to hide those
inconsistencies.

This should probably be part of
  Commit: 34cab6f4 ("md/raid1: fix test for 'was read error from
  last working device'.")
as it addresses the same issue.  It fixes the same bug and should go
to -stable for same reasons.

Fixes: 76073054 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NNeilBrown <neilb@suse.com>

Some places use helpers now, others don't. We only have the 'is set'
helper, add helpers for setting and clearing flags too.

It was a bit of a mess of atomic vs non-atomic access. With
BIO_UPTODATE gone, we don't have any risk of concurrent access to the
flags. So relax the restriction and don't make any of them atomic. The
flags that do have serialization issues (reffed and chained), we
already handle those separately.
Signed-off-by: NJens Axboe <axboe@fb.com>

Currently we have two different ways to signal an I/O error on a BIO:

 (1) by clearing the BIO_UPTODATE flag
 (2) by returning a Linux errno value to the bi_end_io callback

The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario.  Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.

So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NNeilBrown <neilb@suse.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.

A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: NDavid Teigland <teigland@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

When we get a read error from the last working device, we don't
try to repair it, and don't fail the device.  We simple report a
read error to the caller.

However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device.  However a spare which is rebuilding
would be non-faulty but so not the only working device.

So change the test from "!Faulty" to "In_sync".  If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.

This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: NAlexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NNeilBrown <neilb@suse.com>

Currently, a bdi (backing_dev_info) embeds single wb (bdi_writeback)
and the role of the separation is unclear.  For cgroup support for
writeback IOs, a bdi will be updated to host multiple wb's where each
wb serves writeback IOs of a different cgroup on the bdi.  To achieve
that, a wb should carry all states necessary for servicing writeback
IOs for a cgroup independently.

This patch moves bdi->state into wb.

* enum bdi_state is renamed to wb_state and the prefix of all enums is
  changed from BDI_ to WB_.

* Explicit zeroing of bdi->state is removed without adding zeoring of
  wb->state as the whole data structure is zeroed on init anyway.

* As there's still only one bdi_writeback per backing_dev_info, all
  uses of bdi->state are mechanically replaced with bdi->wb.state
  introducing no behavior changes.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: drbd-dev@lists.linbit.com
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

This option is not well justified and testing suggests that
it hardly ever makes any difference.

The comment suggests there might be a need to wait for non-resync
activity indicated by ->nr_waiting, however raise_barrier()
already waits for all of that.

So just remove it to simplify reasoning about speed limiting.

This allows us to remove a 'FIXME' comment from raid5.c as that
never used the flag.
Signed-off-by: NNeilBrown <neilb@suse.de>

When a drive is marked write-mostly it should only be the
target of reads if there is no other option.

This behaviour was broken by

commit 9dedf603
    md/raid1: read balance chooses idlest disk for SSD

which causes a write-mostly device to be *preferred* is some cases.

Restore correct behaviour by checking and setting
best_dist_disk and best_pending_disk rather than best_disk.

We only need to test one of these as they are both changed
from -1 or >=0 at the same time.

As we leave min_pending and best_dist unchanged, any non-write-mostly
device will appear better than the write-mostly device.
Reported-by: NTomáš Hodek <tomas.hodek@volny.cz>
Reported-by: NDark Penguin <darkpenguin@yandex.ru>
Signed-off-by: NNeilBrown <neilb@suse.de>
Link: http://marc.info/?l=linux-raid&m=135982797322422
Fixes: 9dedf603
Cc: stable@vger.kernel.org (3.6+)

Algorithm:
1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues
   ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD)
2. Node 1 sends NEWDISK with uuid and slot number
3. Other nodes issue kobject_uevent_env with uuid and slot number
(Steps 4,5 could be a udev rule)
4. In userspace, the node searches for the disk, perhaps
   using blkid -t SUB_UUID=""
5. Other nodes issue either of the following depending on whether the disk
   was found:
   ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and
	 disc.number set to slot number)
   ioctl(CLUSTERED_DISK_NACK)
6. Other nodes drop lock on no-new-devs (CR) if device is found
7. Node 1 attempts EX lock on no-new-devs
8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk
   as SpareLocal
9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED
10. Other nodes understand if the device is added or not by reading the superblock again after receiving the METADATA_UPDATED message.
Signed-off-by: NLidong Zhong <lzhong@suse.com>
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>

set choose_first true for cluster read in read balance when the area
is resyncing.
Signed-off-by: NLidong Zhong <lzhong@suse.com>
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>

If there is a resync going on, all nodes must suspend writes to the
range. This is recorded in the suspend_info/suspend_list.

If there is an I/O within the ranges of any of the suspend_info,
should_suspend will return 1.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>

This modifies raid1's narrow_write_error to round up block_sectors to the
device's logical block size.

This prevents sd complaining about "Bad block number requested" for non-512-byte
sector disks.
Signed-off-by: NNate Dailey <nate.dailey@stratus.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Now that the ->stop function only frees the private data,
rename is accordingly.

Also pass in the private pointer as an arg rather than using
mddev->private.  This flexibility will be useful in level_store().

Finally, don't clear ->private.  It doesn't make sense to clear
it seeing that isn't what we free, and it is no longer necessary
to clear ->private (it was some time ago before  ->to_remove was
introduced).

Setting ->to_remove in ->free() is a bit of a wart, but not a
big problem at the moment.
Signed-off-by: NNeilBrown <neilb@suse.de>

Each md personality has a 'stop' operation which does two
things:
 1/ it finalizes some aspects of the array to ensure nothing
    is accessing the ->private data
 2/ it frees the ->private data.

All the steps in '1' can apply to all arrays and so can be
performed in common code.

This is useful as in the case where we change the personality which
manages an array (in level_store()), it would be helpful to do
step 1 early, and step 2 later.

So split the 'step 1' functionality out into a new mddev_detach().
Signed-off-by: NNeilBrown <neilb@suse.de>

There is no locking around calls to merge_bvec_fn(), so
it is possible that calls which coincide with a level (or personality)
change could go wrong.

So create a central dispatch point for these functions and use
rcu_read_lock().
If the array is suspended, reject any merge that can be rejected.
If not, we know it is safe to call the function.
Signed-off-by: NNeilBrown <neilb@suse.de>

There is currently no locking around calls to the 'congested'
bdi function.  If called at an awkward time while an array is
being converted from one level (or personality) to another, there
is a tiny chance of running code in an unreferenced module etc.

So add a 'congested' function to the md_personality operations
structure, and call it with appropriate locking from a central
'mddev_congested'.

When the array personality is changing the array will be 'suspended'
so no IO is processed.
If mddev_congested detects this, it simply reports that the
array is congested, which is a safe guess.
As mddev_suspend calls synchronize_rcu(), mddev_congested can
avoid races by included the whole call inside an rcu_read_lock()
region.
This require that the congested functions for all subordinate devices
can be run under rcu_lock.  Fortunately this is the case.
Signed-off-by: NNeilBrown <neilb@suse.de>

My editor shows much of this is RED.
Signed-off-by: NNeilBrown <neilb@suse.de>

process_checks() always returns '0', so change it to 'void'.
Signed-off-by: NNeilBrown <neilb@suse.de>

Using {set,clear}_bit is more consistent than shifting and masking.

No functional change.
Signed-off-by: NNeilBrown <neilb@suse.de>