SoM based on i.MX6 Quad with 1GB of DDR3.

https://boundarydevices.com/product/nit6x-som-v2/Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add FEC support for Engicam i.CoreM6 dql modules.

Observed similar 'eth0: link is not ready' issue which was
discussed in [1] due rmii mode with external ref_clk, so added
clock node along with the properties mentioned by Shawn in [2]

FEC link log:
------------
$ ifconfig eth0 up
[   27.905187] SMSC LAN8710/LAN8720 2188000.ethernet:00: attached PHY driver
               [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
[   27.918982] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[1] https://patchwork.kernel.org/patch/3491061/
[2] https://patchwork.kernel.org/patch/3490511/

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.CoreM6 DualLite/Solo modules are system on module solutions manufactured
by Engicam with following characteristics:
CPU           NXP i.MX6 DL, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.CoreM6 Quad/Dual modules are system on module solutions manufactured
by Engicam with following characteristics:
CPU           NXP i.MX6 DQ, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

With commit 851ce932 ("usb: chipidea: otg: don't wait vbus
drops below BSV when starts host"), the driver can support
enabling vbus output without software control, so this board
(control vbus output through ID pin) can support dual-role now.
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

liteBoard is a development board which uses liteSOM as its base.

Hardware specification:
 * liteSOM (i.MX6UL, DRAM, eMMC)
 * Ethernet PHY (id 0)
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This is a SOM (System on Module), so it will be part of another boards.
Hence, this is a "dtsi" file that will be included from another device
tree files.

Hardware specification:
 * Freescale i.MX6UL SoC
 * up to 512 MB RAM
 * eMMC on uSDHC2
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable PWM1, otherwise the backlight cannot work.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add initial device trees for UDOO Neo Basic, Extended and Full boards:
* Serial console is enabled, other serial ports are prepared.
* I2C based PMIC is enabled.
* Ethernet is enabled for Basic and Full.
* SDHC is enabled, with the SDIO_PWR GPIO modeled as a regulator.
* Both user LEDs are enabled, with the orange one reserved for the M4
  and with the SD card as default trigger for the red LED.

The decision on a board compatible string is deferred to later.

Cc: Ettore Chimenti <ettore.chimenti@udoo.org>
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Also add nodes and properties for thermal management support.
Signed-off-by: NJia Hongtao <hongtao.jia@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable DMA for DSPI on Vybrid.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The LCDIF interrupt should be triggered by the rising edge of the
IRQ line because we only want the interrupt to trigger once per each
frame. It seems the LCDIF IRQ line cannot be explicitly de-asserted
by software, so the previous behavior before this patch, where the
interrupt was triggered by level-high status of the IRQ line, caused
the interrupt to fire again immediatelly after it was handled, which
caused the system to lock up due to the high rate of interrupts.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add node corresponding to OCOTP IP block.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

I2C3 bus was only brought out in revision A1 of the board and revision
B1 only brings out 3 I2C busses (I2C0, I2C1 and I2C2).
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fixed error in trailing whitespace in wandboard-rev1 dtsi.
Signed-off-by: NJagan Teki <jteki@openedev.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fixed code indent tabs in respetcive imx6qdl dtsi files.
Signed-off-by: NJagan Teki <jteki@openedev.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Fixed no space before tabs warnings in respetcive imx6qdl dtsi files.
Signed-off-by: NJagan Teki <jteki@openedev.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Calibrate the USB PHY TX settings to pass the eye diagram signal
integrity test.  The settings are taken from the i.MX6 reference
manual's recommended configuration for USB certification (66.2.6).
Signed-off-by: NJaret Cantu <jaret.cantu@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Use enable-gpios property of PWM backlight driver for backlight
control.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Remove use of pwm-leds and use the standard /sys/class/pwm
interface from PWM subsystem.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Acked-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Toradex Colibri iMX6 module.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Acked-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Pull befs fixes from Luis de Bethencourt:
 "I recently took maintainership of the befs file system [0]. This is
  the first time I send you a git pull request, so please let me know if
  all the below is OK.

  Salah Triki and myself have been cleaning the code and fixing a few
  small bugs.

  Sorry I couldn't send this sooner in the merge window, I was waiting
  to have my GPG key signed by kernel members at ELCE in Berlin a few
  days ago."

[0] https://lkml.org/lkml/2016/7/27/502

* tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs: (39 commits)
  befs: befs: fix style issues in datastream.c
  befs: improve documentation in datastream.c
  befs: fix typos in datastream.c
  befs: fix typos in btree.c
  befs: fix style issues in super.c
  befs: fix comment style
  befs: add check for ag_shift in superblock
  befs: dump inode_size superblock information
  befs: remove unnecessary initialization
  befs: fix typo in befs_sb_info
  befs: add flags field to validate superblock state
  befs: fix typo in befs_find_key
  befs: remove unused BEFS_BT_PARMATCH
  fs: befs: remove ret variable
  fs: befs: remove in vain variable assignment
  fs: befs: remove unnecessary *befs_sb variable
  fs: befs: remove useless initialization to zero
  fs: befs: remove in vain variable assignment
  fs: befs: Insert NULL inode to dentry
  fs: befs: Remove useless calls to brelse in befs_find_brun_dblindirect
  ...

Pull gcc plugins update from Kees Cook:
 "This adds a new gcc plugin named "latent_entropy". It is designed to
  extract as much possible uncertainty from a running system at boot
  time as possible, hoping to capitalize on any possible variation in
  CPU operation (due to runtime data differences, hardware differences,
  SMP ordering, thermal timing variation, cache behavior, etc).

  At the very least, this plugin is a much more comprehensive example
  for how to manipulate kernel code using the gcc plugin internals"

* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  latent_entropy: Mark functions with __latent_entropy
  gcc-plugins: Add latent_entropy plugin

Pull MIPS updates from Ralf Baechle:
 "This is the main MIPS pull request for 4.9:

  MIPS core arch code:
   - traps: 64bit kernels should read CP0_EBase 64bit
   - traps: Convert ebase to KSEG0
   - c-r4k: Drop bc_wback_inv() from icache flush
   - c-r4k: Split user/kernel flush_icache_range()
   - cacheflush: Use __flush_icache_user_range()
   - uprobes: Flush icache via kernel address
   - KVM: Use __local_flush_icache_user_range()
   - c-r4k: Fix flush_icache_range() for EVA
   - Fix -mabi=64 build of vdso.lds
   - VDSO: Drop duplicated -I*/-E* aflags
   - tracing: move insn_has_delay_slot to a shared header
   - tracing: disable uprobe/kprobe on compact branch instructions
   - ptrace: Fix regs_return_value for kernel context
   - Squash lines for simple wrapper functions
   - Move identification of VP(E) into proc.c from smp-mt.c
   - Add definitions of SYNC barrierstype values
   - traps: Ensure full EBase is written
   - tlb-r4k: If there are wired entries, don't use TLBINVF
   - Sanitise coherentio semantics
   - dma-default: Don't check hw_coherentio if device is non-coherent
   - Support per-device DMA coherence
   - Adjust MIPS64 CAC_BASE to reflect Config.K0
   - Support generating Flattened Image Trees (.itb)
   - generic: Introduce generic DT-based board support
   - generic: Convert SEAD-3 to a generic board
   - Enable hardened usercopy
   - Don't specify STACKPROTECTOR in defconfigs

  Octeon:
   - Delete dead code and files across the platform.
   - Change to use all memory into use by default.
   - Rename upper case variables in setup code to lowercase.
   - Delete legacy hack for broken bootloaders.
   - Leave maintaining the link state to the actual ethernet/PHY drivers.
   - Add DTS for D-Link DSR-500N.
   - Fix PCI interrupt routing on D-Link DSR-500N.

  Pistachio:
   - Remove ANDROID_TIMED_OUTPUT from defconfig

  TX39xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  TX49xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  txx9wdt:
   - Add missing clock (un)prepare calls for CCF

  BMIPS:
   - Add PW, GPIO SDHCI and NAND device node names
   - Support APPENDED_DTB
   - Add missing bcm97435svmb to DT_NONE
   - Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
   - Add DT examples for BCM63268, BCM3368 and BCM6362
   - Add support for BCM3368 and BCM6362

  PCI
   - Reduce stack frame usage
   - Use struct list_head lists
   - Support for CONFIG_PCI_DOMAINS_GENERIC
   - Make pcibios_set_cache_line_size an initcall
   - Inline pcibios_assign_all_busses
   - Split pci.c into pci.c & pci-legacy.c
   - Introduce CONFIG_PCI_DRIVERS_LEGACY
   - Support generic drivers

  CPC
   - Convert bare 'unsigned' to 'unsigned int'
   - Avoid lock when MIPS CM >= 3 is present

  GIC:
   - Delete unused file smp-gic.c

  mt7620:
   - Delete unnecessary assignment for the field "owner" from PCI

  BCM63xx:
   - Let clk_disable() return immediately if clk is NULL

  pm-cps:
   - Change FSB workaround to CPU blacklist
   - Update comments on barrier instructions
   - Use MIPS standard lightweight ordering barrier
   - Use MIPS standard completion barrier
   - Remove selection of sync types
   - Add MIPSr6 CPU support
   - Support CM3 changes to Coherence Enable Register

  SMP:
   - Wrap call to mips_cpc_lock_other in mips_cm_lock_other
   - Introduce mechanism for freeing and allocating IPIs

  cpuidle:
   - cpuidle-cps: Enable use with MIPSr6 CPUs.

  SEAD3:
   - Rewrite to use DT and generic kernel feature.

  USB:
   - host: ehci-sead3: Remove SEAD-3 EHCI code

  FBDEV:
   - cobalt_lcdfb: Drop SEAD3 support

  dt-bindings:
   -  Document a binding for simple ASCII LCDs

  auxdisplay:
   - img-ascii-lcd: driver for simple ASCII LCD displays

  irqchip i8259:
   - i8259: Add domain before mapping parent irq
   - i8259: Allow platforms to override poll function
   - i8259: Remove unused i8259A_irq_pending

  Malta:
   - Rewrite to use DT

  of/platform:
   - Probe "isa" busses by default

  CM:
   - Print CM error reports upon bus errors

  Module:
   - Migrate exception table users off module.h and onto extable.h
   - Make various drivers explicitly non-modular:
   - Audit and remove any unnecessary uses of module.h

  mailmap:
   - Canonicalize to Qais' current email address.

  Documentation:
   - MIPS supports HAVE_REGS_AND_STACK_ACCESS_API

  Loongson1C:
   - Add CPU support for Loongson1C
   - Add board support
   - Add defconfig
   - Add RTC support for Loongson1C board

  All this except one Documentation fix has sat in linux-next and has
  survived Imagination's automated build test system"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
  Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
  MIPS: ptrace: Fix regs_return_value for kernel context
  MIPS: VDSO: Drop duplicated -I*/-E* aflags
  MIPS: Fix -mabi=64 build of vdso.lds
  MIPS: Enable hardened usercopy
  MIPS: generic: Convert SEAD-3 to a generic board
  MIPS: generic: Introduce generic DT-based board support
  MIPS: Support generating Flattened Image Trees (.itb)
  MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
  MIPS: Print CM error reports upon bus errors
  MIPS: Support per-device DMA coherence
  MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
  MIPS: Sanitise coherentio semantics
  MIPS: PCI: Support generic drivers
  MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
  MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
  MIPS: PCI: Inline pcibios_assign_all_busses
  MIPS: PCI: Make pcibios_set_cache_line_size an initcall
  MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
  MIPS: PCI: Use struct list_head lists
  ...

Pull sound fixes from Takashi Iwai:
 "Just a few trivial small fixes"

* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: line6: fix a crash in line6_hwdep_write()
  ALSA: seq: fix passing wrong pointer in function call of compatibility layer
  ALSA: hda - Fix a failure of micmute led when having multi adcs
  ALSA: line6: Fix POD X3 Live audio input

Pull more misc uaccess and vfs updates from Al Viro:
 "The rest of the stuff from -next (more uaccess work) + assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  score: traps: Add missing include file to fix build error
  fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
  fs/super.c: fix race between freeze_super() and thaw_super()
  overlayfs: Fix setting IOP_XATTR flag
  iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
  blackfin: no access_ok() for __copy_{to,from}_user()
  arm64: don't zero in __copy_from_user{,_inatomic}
  arm: don't zero in __copy_from_user_inatomic()/__copy_from_user()
  arc: don't leak bits of kernel stack into coredump
  alpha: get rid of tail-zeroing in __copy_user()

Pull cifs fixes from Steve French:
 "Including:

   - nine bug fixes for stable. Some of these we found at the recent two
     weeks of SMB3 test events/plugfests.

   - significant improvements in reconnection (e.g. if server or network
     crashes) especially when mounted with "persistenthandles" or to
     server which advertises Continuous Availability on the share.

   - a new mount option "idsfromsid" which improves POSIX compatibility
     in some cases (when winbind not configured e.g.) by better (and
     faster) fetching uid/gid from acl (when "cifsacl" mount option is
     enabled). NB: we are almost complete work on "cifsacl" (querying
     mode/uid/gid from ACL) for SMB3, but SMB3 support for cifsacl is
     not included in this set.

   - improved handling for SMB3 "credits" (even if server is buggy)

  Still working on two sets of changes:

   - cifsacl enablement for SMB3

   - cleanup of RFC1001 length calculation (so we can handle encryption
     and multichannel and RDMA)

  And a couple of new bugs were reported recently (unrelated to above)
  so will probably have another merge request next week"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
  CIFS: Retrieve uid and gid from special sid if enabled
  CIFS: Add new mount option to set owner uid and gid from special sids in acl
  CIFS: Reset read oplock to NONE if we have mandatory locks after reopen
  CIFS: Fix persistent handles re-opening on reconnect
  SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup
  SMB2: Separate Kerberos authentication from SMB2_sess_setup
  Expose cifs module parameters in sysfs
  Cleanup missing frees on some ioctls
  Enable previous version support
  Do not send SMB3 SET_INFO request if nothing is changing
  SMB3: Add mount parameter to allow user to override max credits
  fs/cifs: reopen persistent handles on reconnect
  Clarify locking of cifs file and tcon structures and make more granular
  Fix regression which breaks DFS mounting
  fs/cifs: keep guid when assigning fid to fileinfo
  SMB3: GUIDs should be constructed as random but valid uuids
  Set previous session id correctly on SMB3 reconnect
  cifs: Limit the overall credit acquired
  Display number of credits available
  Add way to query creation time of file via cifs xattr
  ...

Pull btrfs fixes from Chris Mason:
 "Some fixes from Omar and Dave Sterba for our new free space tree.

  This isn't heavily used yet, but as we move toward making it the new
  default we wanted to nail down an endian bug"

* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: tests: uninline member definitions in free_space_extent
  btrfs: tests: constify free space extent specs
  Btrfs: expand free space tree sanity tests to catch endianness bug
  Btrfs: fix extent buffer bitmap tests on big-endian systems
  Btrfs: catch invalid free space trees
  Btrfs: fix mount -o clear_cache,space_cache=v2
  Btrfs: fix free space tree bitmaps on big-endian systems

score images fail to build as follows.

arch/score/kernel/traps.c: In function 'show_stack':
arch/score/kernel/traps.c:55:3: error:
	implicit declaration of function '__get_user'

__get_user() is declared in asm/uaccess.h, which was previously included
through asm/module.h.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 88dd4a74 ("score: separate extable.h, switch module.h to it")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

sb_wait_write()->percpu_rwsem_release() fools lockdep to avoid the
false-positives. Now that xfs was fixed by Dave's commit dbad7c99
("xfs: stop holding ILOCK over filldir callbacks") we can remove it and
change freeze_super() and thaw_super() to run with s_writers.rw_sem locks
held; we add two trivial helpers for that, lockdep_sb_freeze_release()
and lockdep_sb_freeze_acquire().

xfstests-dev/check `grep -il freeze tests/*/???` does not trigger any
warning from lockdep.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pull overlayfs updates from Miklos Szeredi:
 "This update contains fixes to the "use mounter's permission to access
  underlying layers" area, and miscellaneous other fixes and cleanups.

  No new features this time"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: use vfs_get_link()
  vfs: add vfs_get_link() helper
  ovl: use generic_readlink
  ovl: explain error values when removing acl from workdir
  ovl: Fix info leak in ovl_lookup_temp()
  ovl: during copy up, switch to mounter's creds early
  ovl: lookup: do getxattr with mounter's permission
  ovl: copy_up_xattr(): use strnlen

Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than
frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which
drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering.

In this case thaw_super() will wrongly call s_op->unfreeze_fs() before
it was actually frozen, and call sb_freeze_unlock() which leads to the
unbalanced percpu_up_write(). Unfortunately lockdep can't detect this,
so this triggers misc BUG_ON()'s in kernel/rcu/sync.c.
Reported-and-tested-by: NNikolay Borisov <kernel@kyup.com>
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

ovl_fill_super calls ovl_new_inode to create a root inode for the new
superblock before initializing sb->s_xattr.  This wrongly causes
IOP_XATTR to be cleared in i_opflags of the new inode, causing SELinux
to log the following message:

  SELinux: (dev overlay, type overlay) has no xattr support

Fix this by initializing sb->s_xattr and similar fields before calling
ovl_new_inode.
Signed-off-by: NAndreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Both import_iovec() and rw_copy_check_uvector() take an array
(typically small and on-stack) which is used to hold an iovec array copy
from userspace. This is to avoid an expensive memory allocation in the
fast path (i.e. few iovec elements).

The caller may have to check whether these functions actually used
the provided buffer or allocated a new one -- but this differs between
the too. Let's just add a kernel doc to clarify what the semantics are
for each function.
Signed-off-by: NVegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Merge tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest updates from Shuah Khan:
 "This update consists of:

   - Fixes and improvements to existing tests

   - Moving code from Documentation to selftests, samples, and tools:

     * Moves dnotify_test, prctl, ptp, vDSO, ia64, watchdog, and
       networking tests from Documentation to selftests.

     * Moves mic/mpssd, misc-devices/mei, timers, watchdog, auxdisplay,
       and blackfin examples from Documentation to samples.

     * Moves accounting, laptops/dslm, and pcmcia/crc32hash tools from
       Documentation to tools.

     * Deletes BUILD_DOCSRC and its dependencies"

* tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (21 commits)
  selftests/futex: Check ANSI terminal color support
  Doc: update 00-INDEX files to reflect the runnable code move
  samples: move blackfin gptimers-example from Documentation
  tools: move pcmcia crc32hash tool from Documentation
  tools: move laptops dslm tool from Documentation
  tools: move accounting tool from Documentation
  samples: move auxdisplay example code from Documentation
  samples: move watchdog example code from Documentation
  samples: move timers example code from Documentation
  samples: move misc-devices/mei example code from Documentation
  samples: move mic/mpssd example code from Documentation
  selftests: Move networking/timestamping from Documentation
  selftests: move watchdog tests from Documentation/watchdog
  selftests: move ia64 tests from Documentation/ia64
  selftests: move vDSO tests from Documentation/vDSO
  selftests: move ptp tests from Documentation/ptp
  selftests: move prctl tests from Documentation/prctl
  selftests: move dnotify_test from Documentation/filesystems
  selftests/timers: Add missing error code assignment before test
  selftests/zram: replace ZRAM_LZ4_COMPRESS
  ...

Pull misc kbuild changes from Michal Marek:
 "Just a few patches on the kbuild.git#misc branch this time:

   - New Coccinelle patch by Nicholas Mc Guire
   - Existing patch fixes by Julia Lawall
   - Minor comment fix by Markus Elfring"

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  Coccinelle: flag conditions with no effect
  scripts/coccicheck: Update reference for the corresponding documentation
  Coccinelle: pm_runtime: ensure relevance of pm_runtime reports
  Coccinelle: limit memdup_user transformation to GFP_KERNEL case

Pull kbuild updates from Michal Marek:

 - EXPORT_SYMBOL for asm source by Al Viro.

   This does bring a regression, because genksyms no longer generates
   checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
   working on a patch to fix this.

   Plus, we are talking about functions like strcpy(), which rarely
   change prototypes.

 - Fixes for PPC fallout of the above by Stephen Rothwell and Nick
   Piggin

 - fixdep speedup by Alexey Dobriyan.

 - preparatory work by Nick Piggin to allow architectures to build with
   -ffunction-sections, -fdata-sections and --gc-sections

 - CONFIG_THIN_ARCHIVES support by Stephen Rothwell

 - fix for filenames with colons in the initramfs source by me.

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
  initramfs: Escape colons in depfile
  ppc: there is no clear_pages to export
  powerpc/64: whitelist unresolved modversions CRCs
  kbuild: -ffunction-sections fix for archs with conflicting sections
  kbuild: add arch specific post-link Makefile
  kbuild: allow archs to select link dead code/data elimination
  kbuild: allow architectures to use thin archives instead of ld -r
  kbuild: Regenerate genksyms lexer
  kbuild: genksyms fix for typeof handling
  fixdep: faster CONFIG_ search
  ia64: move exports to definitions
  sparc32: debride memcpy.S a bit
  [sparc] unify 32bit and 64bit string.h
  sparc: move exports to definitions
  ppc: move exports to definitions
  arm: move exports to definitions
  s390: move exports to definitions
  m68k: move exports to definitions
  alpha: move exports to actual definitions
  x86: move exports to actual definitions
  ...

Pull one more documentation update from Jonathan Corbet:
 "A single commit converting the mac80211 DocBook template over to
  Sphinx.  Only 32 more to go..."

* tag 'docs-4.9-2' of git://git.lwn.net/linux:
  docs-rst: sphinxify 802.11 documentation